منتجات

نوع المادة: الفولاذ المقاوم للصدأ رقم الجزء المصنع: MQL-202 موضع التركيب: خلفي رقم الجزء الآخر: MQL-202 بلد/منطقة تصنيع السيارات: الصين ميزات خاصة: كاتم صوت تبادل رقم الجزء: MQL-202 النوع: كاتم صوت مقاوم حار! 2 قطعة/المجموعة تعديل سيارة العادم الذيل الخمار تلميح ماسورة من الفولاذ المقاوم للصدأ لاند روفر مع طقم الجسم SVR وصف علامة تجارية جديدة بنسبة 1.100%، لم تستخدم قط. 2. محكم من الفولاذ 3. مادة متينة مقاومة للأشعة فوق البنفسجية والماء والأوساخ والشحوم والملح والحمض الخفيف والزيت. 4. خفيفة الوزن والمتانة، خط بصري مختلف يأتي من وجهات نظر مختلفة. 5. لا تحتاج إلى الطلاء على الإطلاق. سوف يمنحك مظهرًا رياضيًا دون أن يجعله عدوانيًا للغاية. 6. سهل التركيب. دليل التعليمات غير متضمن. سيتم التوصية بشدة بالتركيب الاحترافي الإعداد: مناسبة لسيارة لاند روفر مع طقم هيكل SVR مواصفات السلعة: اللون الفضي المواد: الفولاذ المقاوم للصدأ 304 حجم المدخل: 7.0 سم الوزن: 4 كجم الحزمة تشمل: 2 قطعة/المجموعة × أنبوب عادم السيارة من الفولاذ المقاوم للصدأ

شبكة رينج روفر أوتوبيوغرافي باللون الأسود. سهل التنصيب التعليمات المتاحة. جودة عالية نفس الأصلية.

Victorious Automotive · Toyota Land Cruiser · Interior Protection Tail Door Guard Board for Toyota Land Cruiser 300 LC300 Premium 304 stainless steel tailgate threshold protection that elevates interior aesthetics while safeguarding high-contact areas. LC300 2021–2024 304 Stainless Steel Lossless Installation Multiple Finishes Overview The Toyota Land Cruiser 300 LC300 (2021–2024) is one of the most capable and luxurious off-road platforms ever built. Its interior deserves protection that matches its premium build quality—particularly high-traffic areas like the tailgate threshold, which endures constant contact and potential scuffing. This Tail Door Guard Board delivers that protection without compromise. Machined from 304 marine-grade stainless steel, it covers the tailgate sill with precision-fit design that mirrors OEM proportions. Available in three distinct finishes—Black Brushed, Silver Brushed, and Grain Texture—it adapts to your LC300's interior scheme while adding visible refinement. Installation is adhesive-based and completely lossless, meaning zero drilling, no permanent modifications, and simple removal if needed. Within minutes, your tailgate threshold transforms from vulnerable trim into a protected, styled accent that signifies attention to detail. What's Included 🛡️ Tail Door Guard Board Precision-cut 304 stainless steel sill guard 🔧 Installation Adhesive Pre-applied or included for secure, clean fit 📖 Fitting Guide Step-by-step installation instructions 🎯 OEM-Matched Sizing Factory-exact dimensions for LC300 Product Highlights 304 Stainless Steel: Marine-grade corrosion resistance, zero rust risk Three Finish Options: Black Brushed, Silver Brushed, Grain Texture OEM-Spec Dimensions: Perfect fit without modification or gaps Protects Threshold: Guards against scuffs, dirt, and wear Adhesive Installation: No drilling, no permanent alterations Lossless Upgrade: Fully removable, leaves no marks or damage Wire Drawing Process: Durable finish applied via precision machinery Improves Appearance: Adds luxury detail and visual grade to cabin Easy Maintenance: Simple to clean and maintain with standard care Quick Installation: Typically complete in under 30 minutes Compatibility Model Year Style Status Toyota Land Cruiser 300 2021 A Style / B Style Direct Fit Toyota Land Cruiser 300 2022 A Style / B Style Direct Fit Toyota Land Cruiser 300 2023 A Style / B Style Direct Fit Toyota Land Cruiser 300 2024 A Style / B Style Direct Fit Installation Difficulty Level: Beginner | Time: 15–25 minutes Open tailgate fully and inspect the threshold area for dust, debris, or moisture. Clean the sill surface thoroughly with a microfiber cloth and mild cleaner; allow to dry completely. Dry-fit the guard board to verify alignment and positioning before adhesive contact. If adhesive is not pre-applied, apply a thin, even layer to the rear surface of the guard board. Carefully position the guard board onto the threshold and press firmly for 10–15 seconds along the entire length. Allow adhesive to cure per manufacturer instructions (typically 24 hours) before opening tailgate or applying pressure. Once cured, verify secure seating and inspect all edges for clean alignment. ⚠️ Important: Ensure the threshold surface is completely dry before installation. Moisture beneath the adhesive will compromise bonding and may cause lifting or misalignment. If removing the guard later, use gentle heat and a plastic scraper to avoid damaging the door sill finish. Protect Your LC300 in Style Every detail counts on a Land Cruiser. This guard board is engineered to protect high-contact surfaces while maintaining the premium look your vehicle deserves. Lossless, adhesive-fit, and available in three premium finishes. Shop LC300 Collection Use code 22GET20 for 20% off any 2 items. 4.9/5 · 12,300+ Reviews ✓ 30-Day Money-Back Guarantee ✓ Worldwide Shipping via DHL, FedEx, UPS Questions? Call +44 203 943 9919 (Mon–Fri 9am–7pm) Victorious Automotive is an independent accessory retailer and is not affiliated with Toyota Motor Corporation, Land Rover, Jaguar Land Rover, or any official Toyota brand. All product names, logos, and brands mentioned are property of their respective owners. This product is designed for compatibility with the specified vehicle and model years but is sold as an aftermarket accessory. ```

Victorious Automotive · Toyota Land Cruiser LC250 · Exterior Trim Tail Door Pedal Trunk Trim Exterior — Toyota Land Cruiser 250 (2024) A precision-cut stainless steel trunk sill guard that protects the Land Cruiser 250's rear entry point while adding a distinctly refined finish to the tailgate area. LC250 2024 Stainless Steel Exterior Trim Trunk Sill Guard 4 Colour Options Adhesive Fit No Drilling Required Overview The 2024 Toyota Land Cruiser 250 represents a landmark return to form — a capable, modern body-on-frame SUV built for those who demand both off-road performance and on-road presence. Owners invest heavily in their LC250 not just for what it can do, but for how it looks doing it. Every detail matters, and the rear tailgate area is one of the most exposed and frequently used parts of the vehicle. This Tail Door Pedal Trunk Trim is engineered specifically for the 2024 Land Cruiser 250, covering the lower edge of the tailgate aperture where wear, scratches, and scuffs inevitably accumulate during daily loading. Whether you're sliding gear into the boot after a weekend trail run or simply loading groceries, this trim acts as a permanent barrier between your cargo and the factory paintwork — while elevating the aesthetics of the rear entry in the process. Constructed from high-grade stainless steel and finished in your choice of four distinctive styles, this trim installs via a clean adhesive bond — no drilling, no permanent modification, and no specialist tools required. It sits flush against the factory panel, complements the LC250's angular exterior language, and adds a layer of premium finish that feels factory-appropriate from day one. What's Included 🪟 Trunk Sill Trim Panel 1 × stainless steel tail door pedal trim piece 🔧 Pre-Applied Adhesive Tape 3M-grade bonding strip pre-fitted to rear face 📋 Installation Guide Step-by-step printed instructions included 🧽 Surface Prep Wipe Alcohol cleaning cloth for bond preparation Product Highlights Precision-formed to match the exact contours of the 2024 LC250 tailgate sill High-grade stainless steel construction — corrosion-resistant and built to last Four finish options: Silver, Black, Fiber Pattern, and Silver Particle Pattern Adhesive installation — no drilling, no modification to factory bodywork Protects original paint from scratches, scuffs, and cargo contact Flush, factory-style fitment that integrates seamlessly with LC250 styling Resistant to UV fade, moisture, and temperature extremes Suitable for all body configurations of the 2024 Land Cruiser 250 Lightweight construction adds no meaningful weight to the tailgate Removable without paint damage if required — adhesive bond is clean and controlled Compatibility Vehicle Code Year Range Fit Toyota Land Cruiser 250 LC250 2024 Direct Fit Toyota Land Cruiser 300 LC300 2021–2024 Not Compatible Toyota Land Cruiser 200 LC200 2008–2021 Not Compatible Toyota Land Cruiser Prado J250 2024 Not Compatible Installation Notes Difficulty: Easy  |  Estimated Time: 15–20 minutes  |  Tools Required: None Open the tailgate fully and ensure the rear sill area is clean, dry, and free from wax, polish, or moisture. Use the included alcohol wipe to thoroughly clean the mounting surface — allow 2–3 minutes to fully dry before proceeding. Dry-fit the trim panel against the sill to confirm alignment and positioning before committing the adhesive bond. Peel the protective backing from the pre-applied adhesive tape, carefully aligning the trim from one end to the other. Press firmly along the full length of the trim for 30–45 seconds to ensure a strong, even bond across the surface. Allow a minimum of 2 hours before use in wet conditions or heavy loading. For best results, avoid loading overnight after installation. ⚠ Important: Ensure installation is carried out at temperatures above 10°C (50°F) for optimal adhesive performance. Do not install on freshly painted or repaired panels — allow new paintwork at least 30 days to fully cure before fitting. Complete Your LC250 Build Explore our full range of exterior and interior accessories for the 2024 Toyota Land Cruiser 250 — designed for owners who expect precision fit, premium finish, and lasting quality. Shop All LC250 Accessories Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 📦 Worldwide Shipping via DHL, FedEx, UPS & TNT 🔄 30-Day Money-Back Guarantee 📞 +44 203 943 9919 Mon–Fri, 9am–7pm Victorious Automotive is an independent aftermarket accessories retailer. This product is not manufactured by, affiliated with, or endorsed by Toyota Motor Corporation or any of its subsidiaries. All vehicle names, model codes, and trademarks referenced are used solely for fitment identification purposes. Always verify compatibility with your specific vehicle configuration before purchase.

Victorious Automotive · Toyota Land Cruiser LC300 · Exhaust Tail Throat Exhaust Pipe Decorative Muffler for Toyota Land Cruiser 300 LC300 Premium stainless steel exhaust trim that transforms the rear end of your LC300 with aggressive styling and lasting durability. LC300 2021–2024 304 Stainless Steel Rust Resistant Exterior Trim Manual Install Overview The Toyota Land Cruiser 300 is a modern icon—commanding presence, refined capability, every detail matters. This tail throat decorative muffler elevates the rear fascia with precision engineering and understated aggression that complements the LC300's already formidable stance. Machined from premium 304 stainless steel, this exhaust pipe trim resists corrosion and road salt, maintaining its finish for years. Available in paint blue or silver, it integrates seamlessly with your vehicle's OEM exhaust outlet, adding depth and character to the rear end without requiring cutting or welding. Built for enthusiasts who refuse compromise: form, function, and longevity. Direct bolt-on installation means no fabrication, no guesswork—just genuine LC300 styling refinement. What's Included 🔧 Decorative Muffler Trim 304 stainless steel, paint blue or silver Product Highlights Custom-engineered fit for 2021–2024 Land Cruiser 300 304 stainless steel construction—premium corrosion resistance Paint blue and silver colorways Bolt-on installation—no cutting or welding required Enhances rear-end aggression and visual depth Road salt and weather resistant OEM-level finish quality and precision Lightweight, zero performance impact Direct fit to factory exhaust outlet Long-term durability with minimal maintenance Compatibility Model Year Range Compatibility Toyota Land Cruiser 300 (LC300) 2021–2024 Direct Fit Toyota Land Cruiser 300 (LC300) 2025+ Not Compatible Toyota Land Cruiser 250 (LC250) All Not Compatible Installation Difficulty: Easy · Time: 15–20 mins Park on a level surface and allow exhaust to cool completely. Locate the factory exhaust outlet at the rear of the vehicle. Align the decorative muffler trim with the outlet opening. Secure using provided stainless steel fasteners. Tighten all connections evenly and verify alignment. Test fitment by visual inspection and gentle hand pressure. Important: Do not attempt installation on a hot exhaust system. Ensure the engine has cooled for at least 30 minutes. If uncertain about fitment, contact our team at +44 203 943 9919 (Mon–Fri 9am–7pm). Why Victorious We work exclusively with Land Rover, Range Rover, Defender, and premium 4×4 enthusiasts. Every product is tested against our exacting standards for fitment, quality, and longevity. This muffler trim meets those same benchmarks—no compromise, no exceptions. Ready to Elevate Your LC300 Transform the rear end of your Land Cruiser 300 with precision engineering and lasting style. Backed by our 30-day money-back guarantee and expert support. Shop LC300 Accessories Use code 22GET20 20% off any 2 items ⭐ 4.9/5 – 12,300+ Reviews 🌍 Worldwide Shipping – DHL, FedEx, UPS, TNT 📞 Expert Support – +44 203 943 9919 ✅ 30-Day Money-Back Guarantee Victorious Automotive is an independent aftermarket accessory specialist. We are not affiliated with, endorsed by, or connected to Land Rover, Range Rover, Jaguar Land Rover, Toyota, or any OEM manufacturer. All product names, logos, and brands are the property of their respective owners. This product is designed to fit the specified vehicles but does not modify or alter the original manufacturer's systems or warranty coverage. Always consult your vehicle manual and local regulations before installation.

Victorious Automotive · Toyota Land Cruiser LC250 · Exterior Trim Tailgate Decoration Bright Strip — Toyota Land Cruiser 250 Prado (2024–2025) A precision-cut stainless steel bright strip that refines the tailgate profile of the LC250 Prado with a clean, factory-integrated finish. LC250 Prado 2024–2025 Stainless Steel Tailgate Trim Silver / Black Adhesive Fit Exterior Accessory No Drilling Overview The Toyota Land Cruiser 250 Prado is one of the most capable and respected SUVs on the road — a vehicle that commands presence both on and off the tarmac. For owners who want to match that reputation with a refined, premium exterior aesthetic, the details matter. The tailgate is one of the most visible surfaces on the LC250, and this bright strip transforms it from functional to finished. Crafted from durable stainless steel, this tailgate decoration strip sits precisely along the rear gate profile, adding a horizontal accent line that draws the eye and gives the rear of the LC250 a more structured, purposeful appearance. Available in Silver for a classic brightwork look, or Black for a more understated, blacked-out build — both options are designed to complement the LC250's contemporary bodywork without overwhelming it. The adhesive installation method means no drilling, no modification, and no risk to your factory bodywork. The strip sits flush and secure when applied correctly, delivering a result that looks as though it was always part of the vehicle. Whether you're building a clean daily driver or a fully kitted overland machine, this is the kind of detail that separates a finished build from a stock one. What's Included 📦 Tailgate Bright Strip × 1 Pre-cut stainless steel trim piece for LC250 tailgate 🔧 Adhesive Tape Pre-Applied High-bond 3M-style backing for secure, clean fitment 🧼 Installation Guide Step-by-step surface prep and fitting instructions Product Highlights Precision-cut for exact fitment on the LC250 Prado tailgate Durable stainless steel construction — resistant to corrosion and UV Available in Silver or Black to suit any exterior build style Adhesive installation — no drilling or modification required Adds a structured, factory-integrated appearance to the rear gate Flush-mount profile for a clean, seamless look when installed Lightweight construction — no impact on tailgate operation Compatible with both standard and lifted LC250 builds Weather-resistant finish suitable for all climates and terrains Reversible — can be removed cleanly without damage to bodywork Compatibility Vehicle Model Code Year Range Fitment Toyota Land Cruiser 250 Prado LC250 2024–2025 Direct Fit Toyota Land Cruiser 300 LC300 2021–2025 Not Compatible Toyota Land Cruiser 200 LC200 2008–2021 Not Compatible Toyota Land Cruiser 150 Prado LC150 2009–2023 Not Compatible Installation Notes 🛠 Difficulty: Easy  |  ⏱ Estimated Time: 15–30 Minutes  |  🔩 Tools Required: None Thoroughly clean the tailgate surface where the strip will be applied. Use an isopropyl alcohol wipe to degrease the area and remove any wax, polish, or contaminants. Allow the surface to dry completely — adhesive performance is significantly reduced on damp or cold surfaces. Ideal application temperature is between 15°C and 30°C. Dry-fit the strip against the tailgate to confirm positioning and alignment before removing the adhesive backing. Peel the adhesive backing from the strip, starting from one end. Carefully align the strip with the tailgate contour and press firmly from the centre outward to avoid air bubbles. Apply firm, even pressure along the full length of the strip for 30–60 seconds to ensure full adhesive contact. Allow the adhesive to cure for a minimum of 24 hours before exposing the vehicle to water, rain, or a car wash. ⚠ Note: Do not apply to freshly painted, repaired, or waxed surfaces. If you are unsure about the installation process, professional fitting is recommended. Incorrect surface preparation is the most common cause of adhesive failure. Complete Your LC250 Build Explore our full range of Toyota Land Cruiser LC250 exterior accessories — each piece selected for quality, fitment, and the kind of finish that serious owners expect. Shop All LC250 Accessories Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 🚚 Worldwide Shipping via DHL, FedEx & UPS ↩ 30-Day Money-Back Guarantee 📞 +44 203 943 9919 Mon–Fri 9am–7pm Victorious Automotive is an independent aftermarket accessory retailer. This product is not manufactured by, affiliated with, or endorsed by Toyota Motor Corporation or any of its subsidiaries. All vehicle names, model codes, and trademarks are the property of their respective owners and are referenced solely for the purpose of describing product compatibility.

```html Jetour · Traveller T2 · Exterior Protection Tailgate Handle Sticker for Jetour Traveller T2 Premium ABS door bowl protection with three finish options. Precision-fit, adhesive-backed, preserves paint and adds aggressive styling. Jetour T2 2023–2026 ABS Material Adhesive Install 3 Finishes Overview The Jetour Traveller T2 is built for adventure, but the exposed door bowl and tailgate handle area can show wear quickly from daily use and outdoor exposure. This tailgate handle sticker protects that vulnerable zone while adding a modern, purposeful edge to your T2's rear end. Machined from premium ABS and available in three distinct finishes—matte black, bright black, or carbon fibre texture—each sticker is engineered to the exact contours of your T2's door bowl. The adhesive backing requires no drilling or modification; installation takes minutes and leaves zero trace if ever removed. Unlike generic protection, this is OEM-profile engineering: rounded edges protect your hands, the low-profile design doesn't interfere with handle function, and the precision fit means no gaps, bubbles, or misalignment. It's the kind of detail that separates a well-finished T2 from the rest. What's Included 🛡️ Tailgate Handle Sticker Precision-fit ABS protection 🧼 Cleaning Cloth Pre-install surface prep 📦 Installation Guide Step-by-step photo reference Product Highlights Original Car Sizing: Engineered to OEM door bowl geometry for perfect fit Three Finish Options: Matte Black, Bright Black, Carbon Fibre Texture Rounded Edges: Protects hands; won't scratch paint or car door Handle Function Preserved: Doesn't interfere with tailgate switch or operation Durable ABS Material: UV-resistant, temperature-stable, long-term durability Adhesive-Backed: No drilling, no modification, reversible installation Protective Coverage: Shields door bowl from scratches, wear, and UV fading Premium Finish Quality: High-gloss or textured options for custom aesthetic Secure Bonding: Industrial-grade adhesive; tested for weather and vibration Minimal Profile: Sleek, integrated look; no bulk or awkward edges Compatibility Model & Year Compatibility Jetour Traveller T2 (2023–2026) Direct Fit Jetour Traveller T2 Early (2023) Direct Fit Jetour Traveller T2 (2024–2025) Direct Fit Jetour Traveller T2 (2026) Direct Fit Other Jetour models Not Compatible Not sure about your model year? Contact our team at +44 203 943 9919 (Mon–Fri 9am–7pm) and we'll confirm fitment before you order. Installation Difficulty Level: Beginner | Time: 10–15 minutes Clean the door bowl area: Use the included cloth to wipe down the tailgate handle zone. Remove any dirt, dust, or residue. Allow to dry completely. Position the sticker: Peel back a small corner of the backing. Align the sticker to the door bowl contours, ensuring even spacing on both sides. Apply gradually: Once positioned, slowly peel away the backing while pressing the sticker down firmly. Work from the centre outward to avoid air bubbles. Press and seal: Use firm, even pressure across the entire surface. Pay special attention to edges and curves to ensure full contact. Allow to cure: Leave undisturbed for 24 hours before opening/closing the tailgate, allowing adhesive to set completely. Note: On older or rough paint, lightly sand and clean the surface before installation. Cold weather may require gentle heat (hair dryer on low) to activate adhesive. Do not force or rush the application. Protect Your T2 Today Add tailgate protection that's as smart as your Jetour Traveller T2. Choose your finish, complete the install in minutes, and enjoy years of guard-dog-grade coverage on one of the most-touched areas on your vehicle. Shop Jetour T2 Accessories Use code 22GET20 for 20% off any 2 items 4.9/5 Stars 12,300+ Reviews 30-Day Money Back Worldwide Shipping Disclaimer: Victorious Automotive is an independent aftermarket specialist. This product is not affiliated with, endorsed by, or manufactured by Jetour or any official Jetour subsidiary. All vehicle names and model designations are the property of their respective manufacturers. Installation of any aftermarket product may affect warranty coverage; consult your dealer for details. ```

Car Tailgate Hinge Frame Fit for JETOUR Traveller T2 C-DM 2026 Modified Auto Tailgate Hinge Decorative Cover Car Accessories Product Introduction 1. The original vehicle profile fits perfectly The original vehicle data, mold and pattern fit comprehensively to protect your car 2. Customized special car service ensures no car door jamming 3. Anti-scratch protection in the original vehicle style The 4.5D carbon fiber has a clear and lustrous texture 5. No glue marks left on the car back adhesive!   If you are not sure whether its fit for your car,just connect with us.we will check it for you.  

Victorious Automotive · Toyota LC250 · Interior Lighting Tailgate Lights for Toyota Land Cruiser 250 Prado LC250 — 2024 & 2025 A purpose-built tailgate lighting upgrade for the LC250 Prado — delivering white cargo illumination, red warning light, and flashing amber hazard signalling directly from the tailgate. LC250 Prado 250 2024–2025 Cargo Light Warning Light Tailgate Mounted Plug-and-Play Interior Upgrade Overview The Toyota Land Cruiser 250 — widely known in international markets as the Prado LC250 — launched in 2024 as a thoroughly modern interpretation of the iconic nameplate. Built for both serious overland work and refined daily use, the LC250 demands accessories that match its dual-purpose engineering ethos. Whether you're loading gear on a remote campsite after dark or parked roadside with the tailgate open, factory lighting rarely meets the practical demands of real-world use. These tailgate lights are engineered specifically for the 2024 and 2025 Land Cruiser 250 Prado, mounting cleanly to the tailgate area and offering three distinct lighting modes: bright white light to flood the cargo bay, steady red light to alert vehicles approaching from behind when stationary, and a flashing white-amber mode ideal as a hazard or attention signal. Each mode serves a genuine purpose — this is not decorative lighting. Installation follows a guided process with no permanent modification required to your LC250. The result is a functional, clean-looking upgrade that feels factory-integrated, adding real utility for overlanding, night-time loading, roadside stops, picnics, and off-road camping — exactly the scenarios this Land Cruiser was built for. What's Included 💡 Tailgate Light Unit Pre-wired LED module designed for LC250 tailgate fitment 🔌 Wiring Harness Vehicle-specific connector harness for clean integration 🔩 Mounting Hardware All fixings and brackets required for fitment 📄 Installation Guide Step-by-step instructions with video support available Product Highlights Designed exclusively for Toyota Land Cruiser 250 Prado (2024–2025) Three lighting modes: white cargo, red warning, white-amber flashing Illuminates boot interior for easy night-time loading and unloading Red steady light warns approaching vehicles when tailgate is open Flashing mode ideal for roadside hazard and campsite visibility Lights up the ground beneath the tailgate for added safety after dark No permanent modification required to the LC250 body or electrics Plug-and-play wiring integration — no specialist tools required Compact, low-profile design maintains the LC250's clean aesthetic Guided installation via included instructions or video walkthrough Compatibility Vehicle Code Year Range Fitment Toyota Land Cruiser 250 Prado LC250 2024–2025 Direct Fit Toyota Land Cruiser 300 LC300 2021–2025 Not Compatible Toyota Land Cruiser 200 LC200 2008–2021 Not Compatible Toyota Land Cruiser 150 Prado LC150 2009–2023 Not Compatible Toyota Hilux Surf / 4Runner — All Years Not Compatible Installation Notes Difficulty: Beginner-Friendly  ·  Estimated Time: 30–60 Minutes  ·  No Drilling Required Open the tailgate of your LC250 fully and locate the interior tailgate panel — no trim removal tools are needed beyond a basic trim pry tool. Carefully release the tailgate interior trim panel clips to access the rear wiring area — take care not to stress the panel. Route the supplied wiring harness to the appropriate power feed point as indicated in the installation guide or video walkthrough. Mount the LED light unit to the designated tailgate position using the supplied brackets and fixings — no permanent holes are required. Connect the wiring harness using the plug connectors provided and test all three lighting modes before refitting trim. Refit the tailgate interior trim panel, ensuring all clips are fully seated and the wiring is neatly routed away from any moving components. Note: Always disconnect the vehicle's 12V power supply before working with any automotive wiring. If you are unsure at any stage, consult a qualified auto-electrician. Installation video guidance is available — contact our team at +44 203 943 9919 (Mon–Fri, 9am–7pm) for support. Upgrade Your LC250 Today Practical, clean, and purpose-built for the Land Cruiser 250 Prado — these tailgate lights are the after-dark upgrade your LC250 deserves. Order today with worldwide DHL, FedEx, UPS & TNT shipping and our 30-day money-back guarantee. Shop LC250 Interior Upgrades Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 Stars — 12,300+ Verified Reviews 🚚 Worldwide Shipping via DHL, FedEx, UPS & TNT 🔄 30-Day Money-Back Guarantee 📞 +44 203 943 9919 Mon–Fri 9am–7pm Victorious Automotive is an independent aftermarket accessory retailer. We are not affiliated with, endorsed by, or connected to Toyota Motor Corporation, Toyota Land Cruiser, or any of their subsidiaries. All product names, model codes, and vehicle references are used solely for fitment identification purposes. All trademarks remain the property of their respective owners.

Victorious Automotive · Toyota Land Cruiser LC250 · Exterior Tailgate Middle Spoiler for Toyota Land Cruiser 250 (2024–2025) A precision-fitted ABS tailgate spoiler that sharpens the rear profile of the LC250 with a clean, factory-integrated finish — no drilling, no fuss. LC250 2024–2025 ABS Material Tailgate Spoiler Pearl White / Black Adhesive Fit Exterior Styling No Drilling Required Overview The Toyota Land Cruiser 250 represents a significant evolution in Toyota's iconic 4x4 lineage — blending genuine off-road capability with a modern, sculpted exterior language. Owners of the LC250 tend to be particular about preserving that aesthetic integrity while making the vehicle unmistakably their own. Every exterior modification should feel considered, not bolted on. This tailgate middle spoiler is engineered specifically for the Land Cruiser 250 platform. Sitting precisely in the mid-section of the tailgate, it adds a subtle yet impactful visual layer that extends the vehicle's roofline flow and gives the rear end a more purposeful, composed stance. Whether your LC250 is finished in Pearl White or you've opted for a darker spec, the two available colour options ensure a near-seamless colour match straight out of the box. Constructed from high-grade ABS plastic, this spoiler is built to withstand UV exposure, temperature extremes and the general demands of daily driving. The adhesive installation method means no drilling into bodywork, no risk of corrosion ingress and no compromise to the tailgate's original functionality — it opens and closes exactly as intended from the factory. What's Included 🪄 Tailgate Middle Spoiler 1 × ABS spoiler unit, colour-matched to specification 🔧 Pre-Applied Adhesive Tape High-bond 3M-style tape pre-fitted to mounting surface 📋 Installation Guide Step-by-step fitting instructions included Product Highlights Designed and engineered exclusively for the Toyota Land Cruiser 250 (2024–2025) Sharpens the rear profile with a clean, aerodynamically considered spoiler line Premium ABS construction — impact-resistant, UV-stable and weather-sealed Adhesive installation requires no drilling, cutting or modification to bodywork Does not interfere with tailgate operation — opens and closes as normal Available in Pearl White and Black to complement factory colour finishes Lightweight fitment adds visual mass without additional load stress Pre-applied high-bond tape ensures a secure, long-term hold in all conditions Surface finish is smooth and consistent — ready for paint or wrap if desired Reversible installation — can be removed cleanly without damaging paintwork Compatibility Vehicle Model Code Year Range Fitment Toyota Land Cruiser 250 LC250 2024–2025 Direct Fit Toyota Land Cruiser 300 LC300 2021–2025 Not Compatible Toyota Land Cruiser 200 LC200 2007–2021 Not Compatible Toyota Land Cruiser Prado 150 J150 2009–2024 Not Compatible Installation Notes 🛠 Difficulty: Easy  ·  Estimated Time: 20–30 Minutes  ·  Tools Required: None Thoroughly clean the tailgate surface where the spoiler will be mounted. Use an isopropyl alcohol wipe to remove all wax, grease and road film — this is critical for adhesive performance. Dry-fit the spoiler to the tailgate to confirm alignment and positioning before committing. Use masking tape to mark the exact placement if needed. Peel back a small section of the adhesive tape backing and carefully align the spoiler to your marked position, pressing the exposed adhesive to the surface first. Once aligned, peel the remaining tape backing while pressing the spoiler firmly along its full length, working from the centre outward to eliminate air pockets. Apply firm, sustained pressure across the entire mounting surface for approximately 60 seconds to activate the adhesive bond. Allow the adhesive to cure for a minimum of 24 hours before washing the vehicle or exposing the area to heavy moisture. ⚠ Note: Installation in temperatures below 10°C (50°F) may reduce initial adhesive tack. If fitting in cold conditions, warm the adhesive tape and mounting surface gently with a heat gun or hair dryer before application. Professional installation is recommended if you are unsure about any step. Complete the Look of Your LC250 Browse the full range of exterior accessories engineered for the Toyota Land Cruiser 250 — from side steps and body cladding to roof rails and mirror covers. Every product ships worldwide via DHL, FedEx, UPS and TNT. Shop All LC250 Accessories Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 🚚 Worldwide Shipping via DHL, FedEx, UPS & TNT ↩ 30-Day Money-Back Guarantee 📞 +44 203 943 9919 Mon–Fri 9am–7pm Victorious Automotive is an independent aftermarket accessories retailer. We are not affiliated with, endorsed by, or connected to Toyota Motor Corporation or any of its subsidiaries. All vehicle names, model codes and trademarks referenced are used for compatibility identification purposes only. Please verify fitment with your specific vehicle variant prior to purchase.

Victorious Automotive · Toyota Land Cruiser 250 · Interior Trim Tailgate Side Speaker Cover – Toyota Land Cruiser 250 (2024) Stainless Steel Interior Upgrade A precision-formed stainless steel speaker surround that refines the Land Cruiser 250's tailgate interior with a clean, upmarket finish — available in Black and Silver. LC250 2024 Model Stainless Steel Tailgate Interior Speaker Surround Black & Silver Paste Fit No Drilling Overview The 2024 Toyota Land Cruiser 250 represents a thoroughly considered return to the Land Cruiser's core values — genuine off-road capability wrapped in a cabin that punches well above the class average. Owners who have invested in the LC250 understand that the details matter, and it's the interior finishing touches that separate a well-specified build from a truly personal one. This Tailgate Side Speaker Cover is engineered specifically for the 2024 Land Cruiser 250. Formed from high-grade stainless steel and available in both Black and Silver, it sits flush over the factory speaker panel at the tailgate, replacing the standard plastic surround with a material that has genuine weight and presence. Whether your build leans utilitarian or upscale, the two colour options allow you to match existing interior trim with precision. Installation is handled via a clean adhesive paste system — no drilling, no permanent modification, and no risk to your factory panel. The result is a subtle but immediately noticeable upgrade that speaks to considered, detail-focused ownership. What's Included 🔲 Tailgate Side Speaker Cover × 1 Stainless steel, custom-formed for LC250 tailgate panel 🧴 Adhesive Mounting Tape Pre-applied or included adhesive pads for no-drill fitment 📋 Installation Guide Step-by-step fitting instructions included Product Highlights Custom-engineered for the 2024 Toyota Land Cruiser 250 tailgate High-grade stainless steel construction for lasting durability Available in Black and Silver to suit varied interior colour schemes Adhesive paste installation — no drilling or permanent modification Protects the factory speaker panel from everyday wear and scuffing Precision-formed for a flush, factory-matching fitment profile Resistant to corrosion, humidity, and temperature fluctuation No special tools required — straightforward DIY installation Immediately elevates the perceived quality of the tailgate interior Fully reversible — can be removed without damaging OEM trim Compatibility Vehicle Model Code Year Range Fitment Toyota Land Cruiser 250 LC250 2024 Direct Fit Toyota Land Cruiser 300 LC300 2021–2024 Not Compatible Toyota Land Cruiser 200 LC200 2008–2021 Not Compatible Toyota Land Cruiser Prado 150 J150 2009–2024 Not Compatible Installation Notes Difficulty: Easy  ·  Estimated Time: 15–20 minutes  ·  Tools Required: None Open the tailgate fully and ensure the speaker panel area is clean, dry, and free from dust or grease. Use an isopropyl alcohol wipe for best adhesion results. Test-fit the speaker cover over the factory panel to confirm alignment and positioning before applying adhesive. Peel the protective backing from the adhesive tape or apply the included paste adhesive evenly across the mounting points on the reverse of the cover. Press the cover firmly into position over the factory speaker surround, holding steady for 30–60 seconds to allow the adhesive to bond. Allow a minimum of 2–4 hours curing time before opening or closing the tailgate to ensure a secure, lasting fit. ⚠ Note: Confirm your vehicle is the 2024 Toyota Land Cruiser 250 (LC250) before fitting. This cover is not compatible with earlier Land Cruiser generations. Avoid installation in temperatures below 10°C as this may affect adhesive performance. Elevate Your LC250 Interior The details define the build. This stainless steel tailgate speaker cover is a small upgrade with a lasting impression — the kind of finish that LC250 owners will notice every time the tailgate opens. Worldwide shipping via DHL, FedEx, UPS, and TNT. Backed by our 30-day money-back guarantee. Shop at Victorious Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 Stars — 12,300+ Verified Reviews 🚚 Worldwide Shipping — DHL, FedEx, UPS, TNT 🔁 30-Day Money-Back Guarantee 📞 +44 203 943 9919 Mon–Fri, 9am–7pm Victorious Automotive is an independent aftermarket accessories retailer. This product is not manufactured by, affiliated with, or endorsed by Toyota Motor Corporation or any of its subsidiaries. All vehicle names, model codes, and trademarks referenced are the property of their respective owners and are used solely for fitment identification purposes.

Automotive · SUV Storage · Interior Organiser Jetour Traveller T2 Tailgate Storage Frame – 2023–2025 Premium trunk storage expansion rack engineered to maximise cargo space and interior organisation for modern Jetour adventurers. Jetour Traveller T2 2023–2025 Steel Frame Direct Fit Cargo Expansion Overview The Jetour Traveller T2 has earned a reputation for serious capability, but interior storage flexibility is where practical modifications make the biggest difference on extended journeys. This tailgate storage frame transforms underutilised rear cargo space into a structured, accessible storage solution—perfect for expedition gear, recovery equipment, or daily adventure essentials. Purpose-engineered for the T2's tailgate design, this frame mounts securely and creates a tiered storage platform that doesn't interfere with boot functionality. Powder-coated steel construction resists corrosion and handles genuine off-road conditions, while the modular design means you can configure it around your specific cargo needs. Whether you're building the ultimate overlanding setup or simply maximising daily practicality, this frame represents the kind of thoughtful interior engineering that separates occasional drivers from committed adventurers. What's Included 📦 Tailgate Storage Frame Complete steel frame assembly with mounting hardware 🔧 Mounting Brackets & Fasteners Grade stainless steel hardware, pre-sorted and labelled 📋 Installation Guide Step-by-step instructions with torque specifications ✓ 30-Day Inspection Period Complimentary support if adjustment or refitting is needed Product Highlights Direct fit for Jetour Traveller T2 (2023–2025) Heavy-duty powder-coated steel construction Expands useable cargo capacity without compromising boot access Modular design supports additional accessories and organisation systems Weather-sealed mounting prevents water ingress or corrosion Rated for off-road vibration and dynamic loads Minimal weight penalty—engineered for efficiency Compatible with roof bars and external storage solutions Non-invasive installation—no permanent modifications Backed by 30-day money-back guarantee Compatibility & Fitment Model / Year Fitment Jetour Traveller T2 (2023–2025) Direct Fit Jetour Traveller T1 (2021–2022) Not Compatible Other Jetour models Not Compatible Unsure about your model? Contact us at +44 203 943 9919 (Mon–Fri, 9am–7pm GMT) and we'll verify fitment for your specific vehicle free of charge. Installation Overview Difficulty Level: Moderate | Time Required: 90–120 minutes Prepare the tailgate area—clear boot space and lay protective covering on interior surfaces Position the frame assembly against the tailgate interior using alignment marks provided Insert and hand-tighten all mounting brackets; do not fully tighten at this stage Verify frame is level and square using a spirit level; make fine adjustments as needed Progressively tighten all fasteners in a cross-pattern to specified torque (see guide for values) Test tailgate operation—should open and close smoothly with no binding or resistance Perform a final visual inspection; ensure all fasteners are tight and no sharp edges are exposed Important: If you're not confident with fastener installation or if you encounter unexpected fitment issues, stop work and contact our team for guidance. Improper installation can affect tailgate function and vehicle safety. Why Choose Victorious for Jetour Storage? We specialise in purposeful interior and exterior upgrades for serious adventurers. Every product is selected and tested against real-world conditions—whether that's expedition logistics, daily practicality, or long-term durability. This storage frame represents years of feedback from T2 owners who demand more from their vehicles. You're not just buying a frame; you're investing in a system that evolves with your journey. Our team stands behind every installation, and we're available to answer questions about fitment, configuration, or integration with other gear. Ready to Expand Your Cargo Capacity? Transform your Jetour Traveller T2's storage potential with premium engineering and genuine expedition practicality. 30-day money-back guarantee. Worldwide shipping on all orders. Add to Cart Use code 22GET20 for 20% off when you purchase any 2 Jetour accessories. ⭐ 4.9/5 – 12,300+ verified reviews 🚚 Worldwide shipping via DHL, FedEx, UPS 📞 Expert support: +44 203 943 9919 ✓ 30-day returns · No questions asked Victorious Automotive is an independent aftermarket specialist. We are not affiliated with Jetour, Chery Automobile, or their parent companies. All product names and vehicle designations are used for identification purposes only. Installation of aftermarket accessories may affect warranty coverage—consult your vehicle manufacturer or authorised dealer for details. ```

Victorious · LC300 · Exterior Tailgate Strip Cover for 2021–2024 Land Cruiser 300 Refined 3D texture finish elevates your LC300's rear profile with premium ABS construction and seamless integration. LC300 2021–2024 ABS Advanced Material 3D Texture Direct Fit Overview The Land Cruiser 300 commands presence on any terrain. This tailgate strip cover enhances that authority with a sculpted 3D finish that catches light and depth in equal measure. Engineered for the 2021–2024 generation, it integrates with factory lines and proportions as if it left the Toyota factory floor this way. Machined from durable ABS advanced polymer, this cover resists UV fade, thermal cycling, and the elements. The textured surface adds visual interest without fussiness—a purposeful upgrade that reads as factory-correct to any enthusiast. Available in deep Black or Silver, both finishes pair intelligently with your LC300's colour palette. Installation uses automotive-grade adhesive for a permanent, lossless bond. No drilling. No brackets. The result is a seamless visual transformation that sits flush with the existing tailgate geometry and lines. What's Included 📦 Tailgate Strip Cover 1× finished ABS component 🧴 Automotive Adhesive Pre-applied or included for installation 📋 Fitment Guide Step-by-step installation notes Product Highlights 3D dimensional texture for premium visual depth and light play Advanced ABS polymer resists UV and thermal degradation Available in Black or Silver; matches LC300 factory palettes Engineered for vehicles 2021–2024 generation; direct fit Seamless integration with factory tailgate lines and proportions Adhesive bond eliminates drilling, brackets, or permanent modification Durable construction withstands off-road conditions and weather exposure Subtle, purposeful design reads factory-correct at first glance Low-maintenance; clean with mild soap and water as needed Reversible application if necessary during ownership transition Compatibility Vehicle Model Years Fitment Toyota Land Cruiser 300 2021–2024 Direct Fit Land Cruiser 300 (earlier/later years) Pre-2021, 2025+ Not Compatible Note: Confirm your vehicle's model year and tailgate geometry before purchase. If in doubt, contact our team at +44 203 943 9919 (Mon–Fri 9am–7pm). Installation Difficulty: Beginner | Time: 15–30 minutes Clean the tailgate surface with automotive soap and dry thoroughly. Use isopropyl alcohol on the adhesive area to remove any residue or wax. Test-fit the strip cover on the tailgate dry, ensuring alignment with factory lines and equal spacing on both sides. Once satisfied with position, mark placement lightly with masking tape or a marker for reference. Apply automotive-grade adhesive (included or specified) to the back of the strip cover according to product instructions. Work in sections if needed. Carefully position the strip cover against the tailgate, aligning with your marks. Press firmly along the entire length, working from centre outward to eliminate air pockets. Allow adhesive to cure fully (typically 24 hours) before opening the tailgate or subjecting the cover to vibration or moisture. Inspect seams and edges. If any lifting occurs post-installation, reapply adhesive and clamp lightly until set. Important: Do not open the tailgate or expose the cover to water for at least 24 hours after installation. Temperature should remain above 10°C during cure. If tailgate requires removal or service in future, consult a professional to avoid damaging the cover. Why Choose This Cover The LC300 represents the pinnacle of Land Cruiser engineering and on-road presence. Every detail matters. This tailgate strip cover respects that philosophy—it's not a badge, not a sticker, not a racing stripe. It's a textured architectural element that adds depth, sophistication, and visual continuity to your rear profile. Built to last through years of service, weather, and the occasional off-road outing, it stands as a permanent, reversible upgrade that enhances without compromising. Ready to Elevate Your LC300 Transform your tailgate with purposeful design and premium materials. Browse our full Land Cruiser LC300 collection for coordinating exterior upgrades. Add to Cart Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ reviews 🚚 Worldwide shipping via DHL, FedEx, UPS, TNT ✓ 30-day money-back guarantee 📞 Expert support: +44 203 943 9919 Victorious Automotive is an independent aftermarket specialist and is not affiliated with Toyota, Land Cruiser, Lexus, or any official Toyota subsidiary. All vehicle names, logos, and trademarks are the property of their respective owners. Product descriptions and compatibility information are provided as guidance only. Buyers are responsible for verifying fitment to their specific vehicle before purchase.

Victorious · Toyota LC300 · Interior Protection Tailgate Toolbox Trunk Protection Board for Land Cruiser LC300 Premium ABS tailgate protection engineered to safeguard your LC300's cargo area against daily wear, scratches, and impacts. LC300 2021–2023 ABS Carbon Fiber Tailgate Protection Easy Install Overview The Toyota Land Cruiser LC300 (2021–2023) is a masterpiece of off-road engineering and luxury. Its spacious cargo area demands protection that matches its premium build. Introducing the Tailgate Toolbox Trunk Protection Board—a purpose-engineered accessory that shields your LC300's tailgate and cargo floor from scratches, impact marks, and general wear. Crafted from durable ABS plastic with an authentic carbon fiber pattern finish, this protection board combines functional durability with visual appeal. Unlike generic rubber mats, this board is precision-molded to fit the LC300's unique tailgate geometry, ensuring seamless integration and a factory-finish appearance. Whether you're hauling recovery gear, loading camping equipment, or simply protecting against day-to-day cargo movement, this protection board delivers peace of mind without compromising your LC300's aesthetic. Installation is straightforward and reversible—no drilling or modification required. What's Included 📦 Tailgate Protection Board 1x precision-molded ABS board 🧴 Adhesive Application Kit Professional-grade installation adhesive 📋 Installation Guide Step-by-step instructions with diagrams 🛡️ 30-Day Protection Guarantee Full refund if not satisfied Product Highlights Precision-molded for perfect LC300 fit (2021–2023) Durable ABS plastic with carbon fiber aesthetic Protects against scratches, scuffs, and impact marks Reversible adhesive installation—no permanent damage Lightweight yet impact-resistant design Factory-finish appearance complements LC300 interior Easy to clean and maintain with standard cleaners Minimal weight penalty on cargo capacity Works with aftermarket cargo organizers Professional installation support available by phone Compatibility Model Years Fit Status Toyota Land Cruiser LC300 2021–2023 Direct Fit Toyota Land Cruiser LC250 2024+ Not Compatible Toyota Land Cruiser 200 2007–2021 Not Compatible Installation Installation Difficulty: Easy | Time Required: 15–20 minutes Clean the tailgate interior thoroughly with rubbing alcohol and allow to dry completely (minimum 30 minutes). Position the protection board on the tailgate floor to verify fit and alignment. Apply adhesive dots to the back of the board at the corners and center points (adhesive kit included). Press firmly into place, holding for 10 seconds at each contact point. Allow adhesive to cure for 2 hours before loading cargo. If repositioning is needed, carefully peel the board away and clean any residue with adhesive remover. Note: Ensure your tailgate surface is completely dry before installation. Do not install in temperatures below 5°C (41°F). For professional installation support, contact us at +44 203 943 9919 (Mon–Fri 9am–7pm). Why Victorious? Since 2010, Victorious has engineered premium protection and styling accessories for Land Rover, Range Rover, and Toyota enthusiasts who refuse to compromise. This protection board reflects our commitment to precision fit, durability, and understated elegance. Built by people who own and drive these vehicles. Ready to Protect Your LC300? Safeguard your Land Cruiser's cargo area with a purpose-engineered protection board that matches your vehicle's premium finish. Order today and drive with confidence. Shop LC300 Accessories Use code 22GET20 for 20% off when you purchase any 2 items. ⭐ 4.9/5 stars from 12,300+ verified reviews 🌍 Worldwide shipping via DHL, FedEx, UPS, TNT ✓ 30-day money-back guarantee 📞 Expert support: +44 203 943 9919 Victorious Automotive is an independent accessory manufacturer and is not affiliated with Toyota, Land Rover, Range Rover, or Jaguar Land Rover Ltd. All vehicle names and brands are registered trademarks of their respective manufacturers. Product compatibility and fitment are subject to individual vehicle specifications and condition.

Victorious · Toyota Land Cruiser LC300 · Exterior Trim Tailgate U-Shaped Decoration Trim Cover for 2021–2024 Toyota Land Cruiser 300 Premium ABS trim upgrade that adds refined contrast to your LC300's tailgate whilst offering lasting protection against UV damage and weathering. LC300 2021–2024 ABS Material Tailgate Trim Paste Installation Overview The Toyota Land Cruiser 300 (LC300) is an uncompromising expedition platform that demands accessories as purposeful as the vehicle itself. This tailgate U-shaped decoration trim cover transforms the visual weight of your rear profile whilst maintaining the OEM aesthetic that Land Cruiser owners expect. Engineered from durable ABS material, this trim sits flush with your tailgate's contours, creating a refined U-shaped accent available in sleek gloss black or premium electroplated finishes. It's not simply a cosmetic upgrade—it shields the underlying panel edges from dirt, salt spray, and UV exposure, extending the longevity of your factory tailgate. Installation is straightforward via clean-surface paste adhesion. No drilling, no permanent modifications. The result is a professional-grade finishing touch that elevates your LC300's exterior presence without compromise. What's Included 📦 U-Shaped Trim Cover One complete tailgate decoration trim 📋 Installation Guide Step-by-step instructions included 🧼 Prep Sheet Alcohol wipe for surface preparation Product Highlights Engineered ABS material for impact and UV resistance Direct-fit design for 2021–2024 LC300 tailgate Available in gloss black and electroplated chrome finishes Premium paste adhesion—no drilling required Protects tailgate panel edges from weathering Refinishes rear profile with purposeful styling accent OEM-matched colour integration Simple one-piece installation in under 20 minutes UV-stabilised finish resists fading and discolouration Backed by 30-day money-back guarantee Compatibility Model Generation Years Compatibility Toyota Land Cruiser LC300 2021–2024 Direct Fit Toyota Land Cruiser LC250 & Earlier Pre-2021 Not Compatible Toyota Land Cruiser LC300+ 2025+ Not Compatible Installation & Fitting Difficulty Level: Easy | Estimated Time: 15–20 Minutes Prepare the tailgate surface. Use the included alcohol prep sheet to thoroughly clean the tailgate area where the trim will sit. Remove any dirt, dust, or residue. Allow to dry completely (minimum 5 minutes). Test-fit the trim. Position the U-shaped cover on the tailgate to confirm proper alignment. Mark reference points if needed. Apply the adhesive. Carefully peel the backing from the pre-applied paste adhesive on the trim cover. Do not touch the adhesive surface. Secure the trim. Press the cover firmly onto the prepared tailgate surface, starting from the centre and working outward. Apply even pressure across the entire U-shaped profile for 30–60 seconds. Allow curing time. Let the adhesive cure for a minimum of 24 hours before exposing the tailgate to washing, rain, or extended sun exposure. Important: Ensure the tailgate surface is completely dry and free of wax, sealant, or protective coatings before installation. Poor surface preparation may result in reduced adhesion. Do not install in direct sunlight or temperatures below 10°C. Complete Your LC300 Exterior This tailgate trim cover is the finishing detail that transforms your Land Cruiser 300 from good to exceptional. Pair it with other exterior upgrades and drive with confidence, knowing every element reflects your commitment to quality. Shop LC300 Accessories Use code 22GET20 for 20% off when you buy any 2 items. 4.9/5 · 12,300+ Reviews 🌍 Worldwide Shipping 💳 30-Day Money-Back 📞 +44 203 943 9919 Victorious Automotive is not affiliated with, endorsed by, or connected to Land Rover, Range Rover, Toyota, or Jaguar Land Rover Limited. All vehicle names, logos, and designs are the property of their respective manufacturers. This product is an aftermarket accessory and is sold as-is for custom vehicle personalisation.

Victorious · Toyota Land Cruiser · Interior Lighting Tailgate Warning Light Upgrade for 2022–2025 LC300 Transform your LC300's rear visibility with premium multi-colour tailgate lighting—safety and style in one elegant upgrade. LC300 2022–2025 Interior Lighting Safety Multi-Colour Overview The 2022–2025 Toyota Land Cruiser LC300 is a formidable expedition platform built for serious off-road work and long-distance adventure. Visibility and safety matter—especially when working at night or during convoy operations where clear communication between vehicles is essential. This Tailgate Warning Light Upgrade delivers intelligent multi-colour lighting to your LC300's rear panel. Choose from white work light, red alert mode, or white–yellow flashing sequences depending on your needs. The result is effortless cargo access in darkness and clear visual communication with trailing vehicles—exactly what serious Land Cruiser drivers expect. Installation is straightforward, requiring only basic tools and roughly 30 minutes of your time. Professional support is available if you need it, and the 30-day money-back guarantee means you're protected against any regret. What's Included 💡 Tailgate Warning Light Premium multi-colour unit, ready to install 📋 Installation Guide Step-by-step printed instructions included 🎬 Video Installation Access Follow along with a professional walk-through Product Highlights Multi-colour LED: White, Red, and White–Yellow flashing modes Enhanced Nighttime Visibility: Perfect for loading cargo after dark Safety Alert System: Alerts following vehicles to maintain safe distance Direct-fit Design: Purpose-built for LC300 tailgate integration Easy Installation: No specialist tools or fabrication required Professional Support: Available by phone Mon–Fri 9am–7pm (GMT) 30-Day Money-Back Guarantee: Full refund if not satisfied Durable Build: Engineered to withstand expedition conditions Low Power Draw: Efficient LED technology preserves battery Vehicle-Specific Fit: Calibrated for 2022–2025 LC300 power systems Compatibility Model Year Range Status Toyota Land Cruiser LC300 2022–2025 Direct Fit Toyota Land Cruiser LC300 2016–2021 (LC200) Not Compatible Toyota Land Cruiser LC250 2024+ Not Compatible Note: Some LC300 units may have non-standard electrical configurations. If you encounter issues, contact our team on +44 203 943 9919 for bespoke support. Installation Difficulty: Easy | Time: 20–30 Minutes Open your LC300 tailgate and locate the mounting point on the inner panel. Disconnect any existing lighting connector (if applicable) to avoid shorts. Position the warning light unit flush against the mounting surface and secure using the provided fasteners. Route the power harness through the tailgate cavity towards the main cabin harness. Connect the power connector to the vehicle's rear lighting circuit (see installation video for exact location). Test all lighting modes: white, red, and flashing sequences. Close the tailgate and verify alignment. You're done. Power Configuration: This unit is designed for standard 2022–2025 LC300 electrical systems. If your vehicle has had previous aftermarket electrical work, verify compatibility before installing. Contact us if unsure. Ready to Upgrade Your LC300? Transform your Land Cruiser's rear visibility with this premium tailgate lighting upgrade. Professional fitment, full support, and a 30-day money-back guarantee—because we stand behind every product we ship. Add to Cart Use code 22GET20 for 20% off when buying 2 items ⭐ 4.9/5 – 12,300+ reviews 🌍 Worldwide shipping via DHL, FedEx, UPS 📞 +44 203 943 9919 – Mon–Fri 9am–7pm Victorious Automotive is an independent accessory specialist and is not affiliated with Land Rover, Range Rover, Toyota, Jaguar Land Rover (JLR), or any official manufacturer. All product names and logos are trademarks of their respective owners. This upgrade is designed to enhance your vehicle's functionality and is sold as an aftermarket accessory only.

Victorious · Defender L663 · Storage Tailgate Window Storage Bag for Defender 90, 110 & 130 Keep essential gear organised and accessible with this purpose-built tailgate window storage solution for your modern Defender. L663 2020–2026 Multi-Pocket Design Direct Fit Tool Storage Overview Whether you're driving a Defender 90, 110, or 130, managing loose items in the cabin can become frustrating quickly. Tools, recovery gear, and daily essentials need a dedicated home—not rolling around the footwell or sliding across the dashboard during rough terrain. This Tailgate Window Storage Bag mounts directly to your Defender's rear window frame, transforming unused space into intelligent, accessible storage. The multi-pocket design keeps items organised and within arm's reach, while the purpose-engineered fit ensures no interference with visibility or functionality. Made to ISO9001 standards in premium facilities, it's built to withstand the demands of serious Defender ownership. Ideal for recovery kit components, tools, charging cables, maps, or emergency supplies—this is the kind of practical upgrade that makes every expedition feel more prepared and professional. What's Included 🎒 Storage Bag Assembly Multi-pocket organiser with mounting hardware 🔧 Fixing Brackets Stainless steel or polymer attachment points 📋 Installation Guide Step-by-step instructions for L663 models ✓ Quality Assurance ISO9001 certified manufacturing standard Product Highlights Tailgate window-mounted design—zero impact on cabin layout Multiple organised pockets for efficient gear separation Engineered for Defender 90, 110, and 130 models Durable materials built for off-road and daily use Tool and recovery kit ready—practical load capacity Easy installation without permanent modifications Direct-fit compatibility with 2020–2026 L663 generation Maintains full rear visibility and operational access ISO9001 factory quality—export-standard durability Protects cargo from road spray and weather exposure Compatibility Vehicle Model Year Range Fit Status Defender 90 (L663) 2020–2026 Direct Fit Defender 110 (L663) 2020–2026 Direct Fit Defender 130 (L663) 2020–2026 Direct Fit Defender (Pre-L663) 2004–2019 Not Compatible Range Rover / Sport All Not Compatible Installation Difficulty: Easy | Time: 15–20 minutes Open your Defender's tailgate fully and secure in position. Locate the window frame attachment points on the upper tailgate panel. Align the storage bag brackets with the mounting holes—brackets should sit flush against the frame. Fasten using the provided hardware (no drilling required); tighten evenly to ensure level installation. Load your gear gradually, testing that the bag sits securely and does not rattle during movement. Confirm rear visibility is unobstructed and the tailgate closes freely. Note: Avoid exceeding the designed load capacity to maintain structural integrity and prevent frame stress. Always check fitment after the first off-road outing to ensure hardware remains secure. Ready to Organise Your Defender? Smart storage transforms your Defender from a capable truck into a prepared, mission-ready companion. This tailgate window bag delivers exactly that—accessible, secure, and built to the standards Defender owners demand. Shop Defender Accessories Save 20% on two items with code 22GET20 4.9★ 12,300+ reviews ✓ 30-day money-back guarantee 📦 Worldwide DHL, FedEx, UPS 📞 +44 203 943 9919 Mon–Fri 9am–7pm Victorious Automotive is an independent aftermarket specialist and is not affiliated with Land Rover, Range Rover, Jaguar Land Rover, or any official Land Rover subsidiary. All product names and vehicle designations are used for compatibility reference only. Always consult your vehicle handbook and contact our team with any compatibility questions before purchase.

اسم العلامة التجارية: تيفانبول المواد: ألياف الكربون وضع الملصق: عجلة القيادة وضع الملصق: لوحة عجلة القيادة طول السلعة: 119 ملم قطر السلعة: 119 ملم الفئة 1: لملصق ميني كوبر F55 F56 الفئة 2: لملحقات ميني كوبر F55 F56 اللون: كما هو موضح Tefanball ألياف الكربون عجلة توجيه سيارة ملصقات غطاء الكسوة لميني كوبر كلوبمان R55 R56 كونتري مان R60 بيسمان R61 اكسسوارات السيارات ملاحظة: المنتج الدائري بيضاوي الشكل قليلاً. إذا وجدت عدم تناسق أثناء التثبيت والاستخدام، فيمكنك تدويره قليلاً لجعله مناسبًا لعجلة القيادة. وصف: علامة تجارية جديدة بنسبة 100% بجودة عالية تتضمن العبوة: قطعة واحدة المواد: ألياف الكربون + الايبوكسي نموذج متوافق: لميني كوبر كلوبمان R55 R56 كونتري مان R60 بيسمان R61 سهلة التركيب مع شريط 3M متصل بالخلف طريقة التثبيت: 1. قم بتنظيف المنطقة وإزالة أي شوائب قبل تركيب هذا المنتج. 2. قم بمحاذاة هذا العنصر مع الموضع المستهدف وفقًا لذلك وقم بتقشير الجزء الخلفي من الشريط 3M. 3. اضغط على العنصر بالتساوي بعد المحاذاة الصحيحة. 4. تجنب أي موقف قد يبلل هذا المنتج خلال 24 ساعة بعد التثبيت. نصائح: يرجى طلب المساعدة من المتخصصين إذا لم تكن متأكدًا من كيفية القيام بذلك. يرجى تسخين الجزء الخلفي من الشريط 3M باستخدام مسدس حراري للحصول على تأثير أفضل للالتصاق عندما تكون درجة الحرارة المحيطة أقل من 20 درجة مئوية. ​

Telescopic Car Wash Mop Experience effortless car cleaning with this highly versatile car wash mop. Its telescopic handle and curved rod design allow for easy reach and prevent damage to car paint, making cleaning a breeze for any vehicle. Product Highlights: 90° adjustable brush handle for unrestricted washing. 15-degree curved design minimizes accidental scratches. Durable aluminum alloy handle ensures longevity and strength. Multi-functional, ideal for cars, motorcycles, windows, and more. Product Specifications: Product Color: Black Yellow Product Size: Brush head 27x15cm, rod length 50cm (extends to 102cm) Material: Aluminum alloy, chenille Carton Size: 72x55x55cm Package Includes: 1 x Telescopic Car Wash Mop Notes: Ensure the mop is cleaned thoroughly after use to maintain its effectiveness and longevity.

أضف لمسة من الفخامة والرقي إلى مقصورة سيارة رينج روڤر الخاصة بك عن طريق تركيب أغطية SVO Autobiography Edition Style هذه. قم بتعزيز التصميم الداخلي لسيارتك Range Rover Sport أو Vogue من خلال تركيب هذا الطراز من SVO. SV (مركبة خاصة) هي جزء من شركة Land Rover التي تنتج سيارات خاصة لسوق السيارات الفاخرة الراقية. إنها تناسب أجزاء هذه المركبات الخاصة بتحسينات فاخرة لا تتوفر في الطرازات الأخرى. تم تجهيز الجزء العلوي من مجموعة SV Autobiography Edition بتحسينات داخلية فاخرة لا يمكن العثور عليها في الطرازات الأخرى. هذه بديل لمقابض التعديل الموجودة لديك. هذا لزوج من مقابض التعديل. مقابض تعديل معدنية ثقيلة الوزن، بلمسة نهائية من الكروم قطع ليزر عالي الجودة مرصع بالألماس. متوفر باللون الفضي أو الذهبي اجعل سيارة رينج روفر الخاصة بك تبدو مختلفة عن الباقي مع هذه الترقية البسيطة. التثبيت في أقل من 5 دقائق!

صندوق تخزين مسند الذراع المركزي للسيارة لطراز تسلا 3 بلوستار 2017 2018 2019 ملحقات حاوية السيارات قفاز المنظم وصف السلعة : الحالة: 100% جديد تمامًا المواد: البلاستيك + السيليكون العبوة: قطعة واحدة مناسبة: لطراز تسلا 3 2017 2018 2019 ملاحظة: يرجى التأكد من شكل سيارتك كما تظهر الصورة لدينا قبل الطلب.

وضع الملصق: مقبض الباب وضع الملصق: وحدة التحكم المركزية وضع الملصق: عجلة القيادة وضع الملصق: فتحة تهوية خلفية المواد: ألياف الكربون .

اسم العلامة التجارية: ميتيوكار وزن السلعة: 200 جرام اسم الموديل: LLK2015 شهادة الاختبار الخارجي: ISO9001 نوع المادة: بلاستيك ارتفاع السلعة: 10 سم عرض السلعة: 20 سم السنة: 2016-2019 نوع العنصر: القوالب الداخلية طول السلعة: 30 سم لون أسود نموذج الإعداد: لـ Tesla MODEL X MODEL S ل تسلا موديل X موديل S صندوق حامل الكأس المركزي للسيارة ملحقات داخلية تستيفها وحدة التحكم المركزية درج منظم

```html Victorious · Land Rover · Cooling System Thermostat Housing & Water Outlet Pipe Kit – Discovery LR3/LR4 · Range Rover Sport · Jaguar XF OEM-equivalent cooling system replacement engineered for Land Rover TDV6 diesel engines and Jaguar 3.0D platforms. LR073372 4H2Q8592BF 2004–2018 2.7–3.0 Diesel Direct Fit PP Housing Overview If you own a Discovery LR3, LR4, Range Rover Sport, or Jaguar XF with the TDV6 2.7 or 3.0-litre diesel engine, the thermostat housing and water outlet pipe assembly is a critical cooling system component. This part regulates engine coolant flow and temperature management—essential for diesel engine longevity and reliability in both road and off-road conditions. Our thermostat housing kit is engineered to match OEM specifications, replacing Jaguar XF, Land Rover Discovery, and Range Rover units that have failed, cracked, or degraded. The polypropylene (PP) construction resists thermal stress and corrosion, and the direct-fit design eliminates fitment confusion and installation guesswork. Worn or failed housings lead to coolant leaks, overheating, and potential engine damage. This kit restores factory cooling performance and is backed by our 30-day money-back guarantee and 12-month manufacturer's warranty. What's Included 🔧 Thermostat Housing Assembly PP polymer, OEM-spec design 🔌 Water Outlet Pipe Integral coolant routing component 📏 Precision-Fit Dimensions 18cm L × 16cm W × 12cm H ✅ Quality Assurance 12-month warranty included Product Highlights OEM-equivalent engineering—replaces LR073372, 4H2Q8592BF, JDE3972, and 1357091 Polypropylene (PP) construction resists thermal cycling and chemical corrosion Direct-fit design—no modifications, adapters, or custom work required Compatible with 2.7 TDV6 and 3.0 SD/TDV6 diesel engines Proven compatibility with Land Rover, Jaguar, and OEM platforms Compact, lightweight design—weight 0.3 kg for easy handling Factory cooling flow specifications maintained Eliminates coolant seepage and overheat risk Straightforward R&R installation—no special tools needed Backed by 30-day money-back guarantee and 12-month warranty Compatibility Vehicle Year Range Engine Fit Land Rover Discovery Mk3 (LR3) 2004–2009 2.7 TDV6 Direct Fit Land Rover Discovery Mk4 (LR4) 2009–2018 2.7 / 3.0 TDV6 Direct Fit Land Rover Range Rover Vogue 2013+ 3.0 SD / TDV6 Direct Fit Land Rover Range Rover Sport L494 2014+ 2.7 / 3.0 TDV6 Direct Fit Jaguar XF 2008+ 3.0 Diesel Direct Fit Jaguar XJ 2009+ 3.0 Diesel Direct Fit Jaguar S-Type 2002–2007 2.7 Diesel Direct Fit Always verify your OEM part number before ordering. Cross-reference your existing housing with the list above: LR073372, 4H2Q8592BF, JDE3972, 1357091, 1316061, 1331447, or C8W0A. If unsure, contact us with your VIN. Installation Notes Difficulty: Intermediate | Time: 1.5–2 hours Prepare: Allow engine to cool completely. Disconnect negative battery terminal and remove engine cover if equipped. Drain coolant: Open radiator petcock and drain coolant into a container. Catch and dispose of properly. Remove old housing: Unbolt the thermostat housing from its mounting points (typically 2–3 bolts). Disconnect coolant hoses and electrical connectors. Clean mounting surface: Wipe the engine block mounting face with a lint-free cloth. Remove old gasket material. Install new housing: Position the new assembly and hand-tighten bolts. Torque to 25 Nm (18 ft-lb) in a cross pattern. Reconnect hoses: Reattach coolant inlet and outlet hoses. Ensure clips are secure. Refill coolant: Use OEM-approved Land Rover or Jaguar coolant (50/50 mix). Bleed air by running engine at idle for 2–3 minutes. Test: Check for leaks. Monitor temperature gauge for 15 minutes of gentle driving. Important: Do not reuse old coolant unless it is less than two years old and has been stored properly. Diesel engines run hotter; use only approved coolant to prevent cavitation and corrosion. Ready to Restore Cooling Performance? This thermostat housing kit is engineered for Land Rover Discovery, Range Rover, and Jaguar XF diesel owners who demand reliability. Backed by our 30-day money-back guarantee and UK support. Shop Thermostat Housing Kit Use code 22GET20 for 20% off when you order 2 or more items. 12,300+ verified reviews 4.9/5 stars 30-day money-back Worldwide DHL · FedEx · UPS Mon–Fri 9am–7pm +44 203 943 9919 Victorious Automotive is an independent aftermarket specialist. We are not affiliated with or endorsed by Jaguar Land Rover, Land Rover, Jaguar, or any OEM brand. All product names and trademarks are the property of their respective owners. This product is designed to be compatible with the specified vehicles and uses OEM-equivalent engineering. Always verify fitment before purchase. ```

```html Victorious · Cooling System · Engine Components Thermostat Housing Kit for Land Rover Discovery & Range Rover OEM-quality water outlet assembly for TDV6 2.7 and 3.0 diesel engines—direct fit, 12-month warranty. Discovery LR3 / LR4 Range Rover Sport 2.7 TDV6 / 3.0 SD Polypropylene Direct Fit New Condition Overview If you own a Discovery LR3, LR4, Range Rover Sport, or Range Rover from 2013 onward with a 2.7 or 3.0 TDV6 diesel engine, you understand the importance of maintaining your cooling system. Engine coolant thermostat housings regulate water flow and temperature distribution throughout your engine bay—when they fail or develop cracks, overheating and coolant leaks follow quickly. This OEM-spec thermostat housing kit is engineered to direct-fit your diesel Land Rover or Range Rover without modification. Manufactured to original equipment specifications using durable polypropylene with reinforced water outlet connections, it replaces failed units that compromise engine temperature regulation and fuel efficiency. Victorious stocks this part in single and dual-unit configurations, making it ideal for planned maintenance or emergency repairs. Every unit ships with a 12-month warranty, worldwide tracking, and 30-day money-back guarantee—because your cooling system deserves the same precision as your suspension and drivetrain. What's Included 📦 Thermostat Housing Assembly OEM-spec polypropylene with integrated water outlet connections 🏷️ Multi-Fitment Confirmation Cross-referenced to 10+ OEM and interchange part numbers ✅ 12-Month Warranty Full coverage against defects; 30-day returns accepted 📍 Worldwide Tracked Shipping DHL, FedEx, UPS via Victorious logistics network Product Highlights OEM Part Numbers: LR073372, JDE3972, 4H2Q8592BF, and 7 more cross-references Fits 2004–2018 Discovery Mk3 & Mk4 (2.7 & 3.0 TDV6) Fits 2013+ Range Rover Vogue and 2014+ Range Rover Sport Compatible with Jaguar XF, XJ, and S-Type 3.0 Diesel variants Direct-fit replacement—no machining, bending, or adapter kits needed Durable polypropylene construction resists thermal stress and coolant degradation Integrated water outlet connections prevent mid-assembly leaks Stable performance under 2.7–3.0L TDV6 operating conditions Single or dual-unit pack options available Ships within 2–3 working days; 30-day money-back guarantee Compatibility Matrix Vehicle & Year Range Engine Fit Land Rover Discovery Mk3 (2004–2009) 2.7 TDV6 Direct Fit Land Rover Discovery Mk4 (2009–2018) 2.7 TDV6 / 3.0 SD / 3.0 TD Direct Fit Range Rover Vogue (2013+) 3.0 TDV6 Direct Fit Range Rover Sport (2014+) 3.0 TDV6 Direct Fit Jaguar S-Type 2.7 Diesel Direct Fit Jaguar XF / XJ 3.0 Diesel Direct Fit Note: Always verify your VIN before purchase. Send us your chassis number via chat for 100% fitment confirmation. Interchange part numbers: 1316061, 1331447, 1357091, C8W0A. Installation Difficulty ⏱️ Intermediate | 45–90 minutes Drain coolant system: Remove negative battery terminal. Open radiator cap and place drain pan beneath the thermostat housing assembly. Loosen housing bolts gradually to prevent coolant spray. Disconnect water outlets: Unclip hose clamps from the failed housing's inlet and outlet pipes. Have towels ready for residual coolant. Remove old housing: Unbolt the assembly from the engine block (typically 4–6 bolts, M8–M10). Discard old rubber seals if present. Install new housing: Position the new OEM assembly and hand-thread bolts first. Torque to 25–30 Nm in a star pattern to avoid warping. Reconnect water lines: Push inlet and outlet hoses onto their respective ports. Secure hose clamps hand-tight, then tighten ¼ turn more using a hose-clamp screwdriver. Refill and bleed: Add fresh coolant (Jaguar/Land Rover spec) to the radiator. Start engine and allow 5–10 minutes for air purge. Watch for leaks at all connection points. Check temperature gauge: Let the engine idle for 10 minutes. Verify no warning lights and normal thermostat operation at the dashboard. ⚠️ Caution: Never work on a hot cooling system. Allow the engine to cool for at least 30 minutes. Wear eye protection when removing the housing—residual coolant can splash. Use OEM-spec coolant only; mixing brands may cause corrosion inside the new housing. Keep Your Cooling System Running Cool Thermostat housings fail silently—often unnoticed until your temperature gauge spikes or a puddle appears under your truck. This OEM-spec replacement kit eliminates the guesswork and the risk of roadside overheating. Direct fit, 12-month warranty, and 30-day returns on every order. Shop Now Use code 22GET20 for 20% off any 2 items. 30-Day money-back guarantee 4.9/5 from 12,300+ reviews Worldwide DHL/FedEx shipping +44 203 943 9919 Mon–Fri 9am–7pm Victorious Automotive is not affiliated with Land Rover, Range Rover, Jaguar, or Jaguar Land Rover plc. This product is a third-party aftermarket replacement part manufactured to OEM specifications. All part numbers, vehicle names, and trademarks are property of their respective manufacturers and are used for identification only. Warranty and guarantee policies apply exclusively under Victorious terms and conditions. ```

SPECIFICATIONSBrand Name: PartsmostCondition: NewFitment Type: Direct ReplacementHigh-concerned chemical: noneInterchange Part Number: 1153 7 510 959, 7 510 959, 7510959Manufacturer Part Number: 11537510959OEM NO.: 70808415, 70808815, 6.618.01, 6.618.01.399Opening Temperature: 105 deg.COrigin: Mainland ChinaPlacement on Vehicle: Engine Cooling SystemReference OE/OEM Number: For MAHLE TM 18 105Warranty: 12 months NEW AUTO ENGINE THERMOSTAT HOUSING WITH GASKET FOR BMW 1 3 X1 X3 Z4 SERIES 1.8i 2.0i 118i 120i 318i 320i E46 E60 E81 E82 E83 E84 E85 E87 E88 E90 E97 N42 N46 COOLANT THERMOSTAT OE NO.: 11537510959   PRODUCT DESCRIPTION: 1) OE quality, OEM quality or aftermarket parts for your choice. 2) According to the original equipment specifications. 3) Perfect match with the original car. 4) Easy and fast installation. 5) Stable performance and high reliability.   ITEM TYPE: Engine Coolant Thermostat & Housing   PART NUMBERS: 11537510959 1153 7 510 959 7 510 959 7510959 70808415 70808815 6.618.01 6.618.01.399 TM18105   COMPATABILITY: FOR BMW 1' Series −E81 +118i N46N +120i N46N −E82 +120i N46N −E87 +118i N46 +120i N46 −E87 Facelift +118i N46N +120i N46N −E88 +118i N46N +120i N46N 3' Series −E46 +316i N42 +316i N46 +316ti N42 +316ti N46 +318Ci N42 +318Ci N46 +318i N42 +318i N46 +318ti N42 +318ti N46 −E90 +318i N46 +318i N46N +320i N46 +320i N46N −E90 Facelift +318i N46N +320i N46N −E91 +318i N46 +318i N46N +320i N46 +320i N46N −E91 Facelift +318i N46N +320i N46N −E92 +320i N46N −E92 Facelift +320i N46N −E93 +320i N46N −E93 Facelift +320i N46N 5' Series −E60 Facelift +520i N46N +520Li N46N X1 Series −E84 +X1 18i N46N X3 Series −E83 +X3 2.0i N46 −E83 Facelift +X3 2.0i N46 Z Series −E85 +Z4 2.0i N46   PACKAGE INCLUDED: 1 x Engine Coolant Thermostat   PRODUCT PHOTOS: If you find that the product images are the same as ours but without our brand logo "Partsmost", it means that other merchants have stolen our product images. Please note that if you purchase from other merchants, you will bear the risks. OEM WAHLER:   SKETCH MAP:     Technical Data Will this item fit your vehicle? - Before purchasing, please pay attention to item Technical Data and check Part Numbers. Make sure that one of these part numbers does coincide with the number of your previous part or does replace your Original Equipment Number. - Surely, in case you doubt in fitment, cannot find the number of your previous part listed in Part Numbers section, or just cannot be sure about item compatibility with your vehicle, please send us your VIN number (Vehicle Identification Number) which is on your Vehicle Registration Certificate or the lower left corner of the front windshield. We are here to assist you to check. - Let's avoid compatibility issues, returns, and get great shopping experience ever!   Payment Method - You can see all payment methods available on Aliexpress and choose the one you prefer. - We also accept Paypal. Please contact us to get more information if you have any doubts. - We offer combined shipping discount. If you purchase more than one item or in big quantity of some items, please feel free to ask us before you make payment how to save shipping cost for you.   Shipping Method & Delivery Time - We use Standard shipping method or Simple shipping method to send goods by Free Shipping. If you have a special requirement, please contact us before you purchase. Tracking numbers will be available to be checked after the packages have been shipped out. Seller's shipping method to Brazil usually refers to "Correios Brazil" and the tracking number can be checked. Delivery time is about 25 days to 45 days. - We can also use Express shipping method like AliExpress Premium Shipping, e-EMS, EMS, DHL, FedEx, UPS to send goods if you need urgently, but please note that you may need to pay import duty and taxes based on the Customs policy of your country. Our selling price does NOT include any Customs charges and local charges! - If you do not want to pay import duties, please contact us, and we will check if there are any duty-free shipping methods are available to your country. NOTE: - In some remote countries like Bosnia and Herzegovina, Saudi Arab, Bolivia, Dominican Republic, South Africa etc., buyers usually can get goods within 60 natural days, but if severe Custom Invesigation happens, delivery time may extend to 100 natural days. - China Post is slower than other standard post shipping method and sometimes its delivery time is longer than 60 days, so we do NOT recommend it if you have not patience to wait for that long time. Please do NOT open any disputes for the reason of "goods still in delivery" if you choose China Post.   Returns - Customers may return an item for refund or exchange within 30 days after the item is received. If return is for any quality problems, we pay return charges. If return is NOT for any quality problems, the buyer should pay return charges. Moreover, items must be returned in their original shipping method and intact packaging and should not be used. - If the package is returned to us for the reason as below, the buyer need to pay for return charges if it occurs and CANNOT get a refund of the freight paid for the order. 1. After the parcel arrives at the destination country, the buyer's address, phone number, zip code is not clear and the buyer cannot be contacted; 2. The buyer did not sign and receive in time; 3. The buyer refused to sign.   About us - We are a professional seller of auto spare parts for British and European car models located in China for more than 10 years, the biggest producing country. With the good quality products we have, we do competitive offer, professional service to customers all over the world. - We choose the suitable shipping way for every country those we ship to. Usually we ship out goods within 3 working days, sometimes within 5 working days during the promotion period. We give satisfy solution to any problems we meet. - We also do business of original parts and OEM brand parts to provide more alternatives for our customers. If you are also interested in them, just feel free to get a quotation from us. - We welcome wholesale orders and we can ship goods by sea, please contact us for more information.   Feedbacks - Once we have received your order, a positive feedback will be automatically sent to you. Please let us to know if you have not received our feedback, we will give feedback manually. - We would also greatly appreciate if you leave us a positive feedback with 5 stars rating. - If you feel that we deserve a neutral or negative feedback, please, CONTACT US before leaving any feedback, give us a chance to make things right and leave your impression most positive!

Victorious Automotive · Toyota Land Cruiser LC250 · Interior Trim Third Row Air Conditioning Vent Decoration Cover – Toyota Land Cruiser 250 (2024) A precision-cut stainless steel vent cover that elevates the LC250's third-row cabin finish with a refined, factory-complementary aesthetic — installed in minutes, no tools required. LC250 2024 Stainless Steel Third Row Interior AC Vent Cover Paste Installation Black & Silver No Drilling Overview The Toyota Land Cruiser 250 is a genuinely significant vehicle — a full reboot of one of the most respected nameplates in off-road history. Its interior has been thoroughly modernised, bringing a level of cabin quality that LC owners haven't seen before. When you're investing in a vehicle at this level, the details matter. That includes the spaces your passengers spend time in — particularly the third row, where the factory AC vent surrounds are functional but understated. This Third Row Air Conditioning Vent Decoration Cover is designed specifically for the 2024 Land Cruiser 250. Crafted from high-grade stainless steel, it overlays your existing AC vent trim with a clean, sculpted surround that immediately elevates the look of the rear cabin. Available in Black and Silver, both finishes are designed to sit harmoniously alongside the LC250's interior palette — whether your vehicle is specced in lighter or darker tones. The installation uses a professional-grade adhesive backing — no drilling, no permanent modification, and no risk to your original panels. It's the kind of upgrade that reads as intentional rather than aftermarket; something that enhances what's already there without drawing unnecessary attention to itself. What's Included 🛡️ Vent Decoration Cover × 1 Third row AC vent surround, stainless steel construction 🔧 Adhesive Tape Pre-Applied Professional-grade 3M-style mounting tape on reverse 📋 Installation Guide Step-by-step instructions included in packaging Product Highlights Precision-engineered fit for the 2024 Toyota Land Cruiser 250 High-grade stainless steel construction for long-term durability Available in Black and Silver to match your interior spec Protects OEM vent surrounds from scuffs and wear Tool-free paste installation — no drilling or cutting required Designed to complement the LC250's factory interior aesthetic Slim-profile overlay — does not obstruct airflow or vent function Resistant to heat, UV exposure, and interior temperature cycles Clean, factory-finished edges with no sharp corners or rough surfaces Reversible — can be removed without damage to original panels Compatibility Vehicle Year Trim / Grade Fitment Toyota Land Cruiser 250 (LC250) 2024 All Grades (GX, GXL, VX, Sahara) Direct Fit Toyota Land Cruiser 300 (LC300) 2022–2024 All Grades Not Compatible Toyota Land Cruiser 200 (LC200) 2008–2021 All Grades Not Compatible Toyota Land Cruiser Prado 150 All Years All Grades Not Compatible Installation Notes Difficulty: Easy  ·  Estimated Time: 15–20 Minutes  ·  Tools Required: None Thoroughly clean the third row AC vent surround area with an isopropyl alcohol wipe and allow to dry completely. Any residue or moisture will reduce adhesive bond strength. Test-fit the decoration cover dry against the vent surround to confirm alignment and positioning before committing to installation. Peel the protective backing from the pre-applied adhesive tape on the reverse of the cover. Carefully position the cover over the vent surround, aligning from one edge inward to avoid trapping air bubbles beneath the surface. Apply firm, even pressure across the entire surface for 30–60 seconds to ensure full adhesive contact. Allow a minimum of 2 hours before exposing the cover to significant heat or airflow from the vents. Full cure is achieved within 24 hours. ⚠ Note: Confirm your vehicle is the 2024 Toyota Land Cruiser 250 before purchase. This cover is not designed for the LC300 or any previous generation Land Cruiser. Applying to an incompatible panel may result in poor fitment or adhesive failure. Complete Your LC250 Interior This vent cover is just one piece of a broader interior upgrade. Browse the full Victorious Toyota Land Cruiser LC250 collection to find complementary trim pieces, console covers, and more — all designed to the same standard. Shop All LC250 Accessories Use code 22GET20 for 20% off when you buy any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 🚚 Worldwide Shipping via DHL, FedEx & UPS ↩️ 30-Day Money-Back Guarantee 📞 Support: +44 203 943 9919 (Mon–Fri, 9am–7pm) Victorious Automotive is an independent retailer and is not affiliated with, endorsed by, or connected to Toyota Motor Corporation or any of its subsidiaries. All vehicle names, model codes, and trademarks referenced are used for fitment identification purposes only and remain the property of their respective owners.

Victorious Automotive · Toyota LC250 · Interior Trim Third Row Left & Right Water Cup Decoration Frame – Toyota Land Cruiser 250 / Prado LC250 (2024) A precision-engineered ABS decoration frame for the third-row cup holders of the 2024 Toyota Land Cruiser 250 and 1958 Prado LC250 — elevating cabin detail with a seamless, scratch-protective finish. LC250 Land Cruiser 250 1958 Prado 2024 High-Grade ABS Silver / Fiber Pattern Third Row Interior Paste Fit No Drilling Interior Trim Overview The 2024 Toyota Land Cruiser 250 — also sold as the 1958 Prado in select markets under the LC250 platform — represents a landmark return to the Land Cruiser's iconic heritage, combining serious off-road capability with a refined, premium cabin. Owners of the LC250 understand that every interior surface matters, and that the factory finish, while good, rarely tells the full story of a personalised, well-considered build. This third-row left and right water cup decoration frame has been developed specifically for the 2024 LC250 cabin geometry. Manufactured from high-grade ABS, it integrates directly over the existing third-row cup holder surrounds on both the left and right sides, creating a clean, elevated look that visually matches the cabin's trim language. Available in Silver and Fiber Pattern finishes, the frame complements both factory and aftermarket interior colour schemes with equal confidence. Beyond aesthetics, the frame serves a practical purpose: protecting the original factory panel surface from everyday wear, key scratches, and drink spillage marking. With a straightforward adhesive installation requiring no drilling, no wiring, and no modification to your vehicle's structure, it's one of the most impactful interior upgrades available for the LC250 at this price point. What's Included 🔲 Left Cup Frame Third-row left-side decoration frame, ABS construction 🔲 Right Cup Frame Third-row right-side decoration frame, ABS construction 🔧 Pre-Applied Adhesive 3M-grade backing tape for secure, clean bonding 📄 Installation Guide Step-by-step fitting reference included Product Highlights Precision-cut ABS frame designed for the 2024 LC250 / 1958 Prado third-row cup holder geometry Available in Silver and Carbon Fiber Pattern finishes to suit your interior scheme Protects original factory panel surfaces from scratches, wear, and daily use marks Covers both left and right third-row positions for a fully symmetrical finish High-grade ABS construction resists warping, UV discolouration, and temperature fluctuation No drilling, no cutting — adhesive-backed paste installation preserves factory warranty integrity Slim-profile design integrates flush with existing trim lines for a factory-style appearance Lightweight fitment adds zero bulk while delivering a noticeably premium cabin feel Instantly elevates perceived cabin quality in the third row, benefiting rear-seat passengers Reversible installation — can be cleanly removed without panel damage if required Compatibility Vehicle Code Year Range Fitment Toyota Land Cruiser 250 LC250 2024–Present Direct Fit Toyota Land Cruiser 1958 Prado LC250 Platform 2024–Present Direct Fit Toyota Land Cruiser 300 Series LC300 2021–Present Not Compatible Toyota Land Cruiser 200 Series LC200 2008–2021 Not Compatible Toyota Land Cruiser Prado 150 J150 2009–2023 Not Compatible Installation Notes Difficulty: Easy  ·  Estimated Time: 10–15 Minutes  ·  Tools Required: None Ensure the third-row cup holder surround panels are clean, dry, and free from dust, grease, or moisture. Use an isopropyl alcohol wipe for best adhesion results. Dry-fit the left and right decoration frames against their respective cup holder surrounds to confirm alignment and verify the fit before committing. Peel the protective backing from the pre-applied adhesive tape on the reverse of each frame, taking care not to touch the adhesive surface. Align the frame precisely over the cup holder surround and press firmly into position, applying even pressure across the full surface for 30–60 seconds. Allow the adhesive bond to cure for a minimum of 2–4 hours at room temperature before subjecting the frames to sustained pressure or vibration. ⚠ Note: Confirm your exact vehicle model year and trim specification prior to ordering. This frame is developed specifically for the 2024 LC250 / 1958 Prado platform. Installing on an incompatible panel may result in poor fitment. If uncertain, contact our team on +44 203 943 9919 before purchase. Complete Your LC250 Interior Trusted by Land Cruiser and 4x4 enthusiasts worldwide, Victorious Automotive delivers precision-fit interior accessories with the attention to detail your vehicle deserves. Backed by our 30-day money-back guarantee and 4.9-star rated customer service. Shop All LC250 Interior Accessories Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 Stars — 12,300+ Verified Reviews 🚚 Worldwide Shipping — DHL, FedEx, UPS, TNT ↩ 30-Day Money-Back Guarantee 📞 +44 203 943 9919 — Mon–Fri, 9am–7pm Victorious Automotive is an independent aftermarket accessory retailer. This product is not manufactured by, affiliated with, endorsed by, or approved by Toyota Motor Corporation or any of its subsidiaries. All vehicle names, model codes, and trademarks referenced are used for compatibility identification purposes only and remain the property of their respective owners. Always verify fitment compatibility with your specific vehicle configuration before purchase.

Toyota · Land Cruiser 250 / Prado LC250 · Interior Accessories Third Row Middle Silica Gel Pad – Toyota Land Cruiser 250 Prado LC250 (2024–2025) A precision-cut silicone protection pad for the third-row middle panel of the 2024–2025 Toyota Land Cruiser 250 Prado — keeping your interior pristine with zero compromise on fit or finish. LC250 Prado 2024–2025 Silicone Material Third Row Interior Protection Direct Fit Black No Drilling Required Overview The Toyota Land Cruiser 250 — known in many markets as the new Prado — represents a bold step forward for Toyota's legendary off-road lineage. With a redesigned interior that balances rugged capability with modern refinement, LC250 owners are understandably protective of every surface inside their vehicle. The third-row area in particular sees significant contact, whether from passengers, cargo, or everyday use — and the factory panel beneath is vulnerable to scratching, scuffing, and general wear. This Third Row Middle Silica Gel Pad is engineered to sit flush and secure directly onto the designated third-row middle panel position of the 2024–2025 LC250, acting as a discreet but highly effective barrier between daily life and your factory trim. Moulded from premium-grade silicone, the pad absorbs contact stress, resists surface damage, and maintains its shape and colour far longer than generic alternatives. Beyond protection, the pad integrates cleanly with the LC250's interior aesthetic — its matte black finish and precision contour ensure it looks like it belongs there. Removable in seconds for cleaning and reinstallable without adhesives or tools, this is the kind of thoughtful interior detail that separates a well-kept LC250 from everything else on the road. What's Included 🟫 Silica Gel Pad × 1 Third row middle position — pre-formed for LC250 📋 Fitment Guide Basic placement reference included Product Highlights Precision-moulded to match the third-row middle panel profile of the 2024–2025 LC250 Premium silicone construction — flexible, durable, and resistant to deformation Protects factory trim from scratches, scuffs, and everyday contact damage Tool-free installation — simply press into the designated panel position Fully removable for quick, effortless cleaning under running water Matte black finish complements the LC250's interior colour palette Maintains secure fitment without adhesives, clips, or permanent fixings Silicone material is heat-stable — won't warp or discolour in high cabin temperatures Low-profile design remains discreet and visually integrated with surrounding trim Long-lasting wear resistance ensures years of reliable interior protection Compatibility Vehicle Model Code Year Range Fit Status Toyota Land Cruiser 250 / Prado LC250 2024–2025 Direct Fit Toyota Land Cruiser 300 LC300 2021–2025 Not Compatible Toyota Land Cruiser 200 LC200 2008–2021 Not Compatible Toyota Land Cruiser 150 / Prado LC150 2009–2023 Not Compatible Toyota 4Runner (All Generations) — All Years Not Compatible Installation Notes ⏱ Estimated Time: Under 5 minutes  ·  🔧 Difficulty: Beginner Ensure the third-row middle panel area is clean, dry, and free of dust or debris before fitting. Remove the silica gel pad from its packaging and orient it to match the panel contour — note any directional markings if present. Align the pad carefully over the designated third-row middle panel position, ensuring all edges sit flush. Apply gentle, even pressure across the pad surface to seat it securely into position — no tools or adhesives required. Check all edges are fully seated and there is no lifting or misalignment before use. To clean, simply lift the pad free, rinse under lukewarm water, allow to dry fully, and refit. ⚠ Note: Always confirm your exact vehicle model year and trim variant before purchasing. This pad is designed exclusively for the Toyota Land Cruiser 250 (LC250) manufactured from 2024 onwards. Fitment on earlier or alternative models is not guaranteed and may result in an incorrect fit. Precision Details. Lasting Protection. Your LC250's interior deserves the same attention to detail as the rest of the build. This silica gel pad is a simple, low-cost upgrade that keeps your third-row trim looking factory-fresh — whether you're running daily errands or heading deep off-road. Shop All LC250 Interior Accessories Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 🚚 Worldwide Shipping via DHL, FedEx & UPS ↩ 30-Day Money-Back Guarantee 📞 +44 203 943 9919 Mon–Fri 9am–7pm Victorious Automotive is an independent aftermarket accessories retailer. This product is not manufactured by, affiliated with, or endorsed by Toyota Motor Corporation or any of its subsidiaries. All vehicle model names, codes, and trademarks referenced are used for fitment identification purposes only. Please verify compatibility with your specific vehicle variant prior to purchase.