ديفندر 110 2020 L663

غطاء محرك السيارة من ألياف الكربون لسيارة لاند روفر ديفيندر 2020 هذا هو قطعة كبيرة. بديل مباشر يضم مغرفة. ملحوظة: هذا المنتج مصنوع من ألياف الكربون الحقيقية ومصنوع يدويًا. يمكن أن تكون العيوب الصغيرة مرئية.

Victorious Automotive · Defender L663 · Exterior Styling Gloss Carbon Fibre Double Scoop Bonnet – Land Rover Defender L663 (2020+) A full bonnet replacement in real gloss carbon fibre — twin performance scoops, precision-moulded fitment, and a finish that transforms the front end of your Defender from the factory floor up. L663 2020–2026 Real Carbon Fibre Double Scoop Gloss Finish OEM Replacement Defender 90 / 110 / 130 UV Protected Overview The Land Rover Defender L663 is a vehicle that commands attention by design — boxy, purposeful, and unmistakably itself. But for owners who want to take that presence a step further, the factory bonnet leaves room for something more considered. This is where form and function meet in a single piece of bodywork. This Gloss Carbon Fibre Double Scoop Bonnet is built from high-grade real carbon fibre, pre-moulded to match the exact geometry of the L663 platform. The twin scoops run the length of the bonnet, adding visual depth and an aggressive performance aesthetic that references motorsport heritage without compromising the Defender's signature silhouette. The deep gloss lacquer finish is UV-stabilised to resist yellowing, fading, and surface degradation over time — a common failure point on lesser carbon replacements. Unlike cosmetic overlays or vinyl wraps, this is a direct OEM-replacement bonnet shell. It swaps out your factory unit entirely, giving you a clean, integrated result that looks factory-fitted rather than aftermarket. Whether your Defender is a daily driver through the city or a weekend machine on gravel tracks, this upgrade delivers a visual statement that holds up in any environment. What's Included 🖤 Carbon Fibre Bonnet Shell 1x pre-moulded double scoop unit in gloss finish 🔩 Mounting Hardware Fixing hardware included where applicable 📋 Fitment Reference Guide Basic alignment and installation notes 🛡️ Protective Packaging Fully wrapped and foam-protected for safe transit Product Highlights Real carbon fibre construction — not a wrap or fibreglass imitation Deep gloss UV-protected lacquer finish, resistant to fading and yellowing Twin double scoop design adds visual aggression and performance depth Pre-moulded to OEM L663 specifications for precise panel alignment Direct replacement for the factory bonnet — no cutting or modification required Lighter than the OEM steel bonnet, reducing front-end weight marginally Impact-resistant carbon layup handles road debris and off-road conditions Compatible with all trim levels including V8, X, X-Dynamic, SE and S Suitable for Defender 90, 110 and 130 body lengths Designed for vehicles without factory bonnet scoops as standard Compatibility Model Variant Year Range Fit Defender 90 S, SE, X-Dynamic, X, V8 2020–2026 Direct Fit Defender 110 S, SE, X-Dynamic, X, V8 2020–2026 Direct Fit Defender 130 S, SE, X-Dynamic, X 2022–2026 Direct Fit Defender 110 Works Works Edition 2021–2023 Direct Fit Classic Defender (L316) All variants Pre-2016 Not Compatible Defender (L663) — Factory Scoop Equipped Any trim with OEM scoops 2020–2026 Check Before Ordering Installation Notes 🔧 Installation Overview — Difficulty: Intermediate to Advanced  |  Estimated Time: 2–4 Hours Open and prop the existing factory bonnet safely. Disconnect any bonnet release cables, washer jet feeds, or wiring looped through the bonnet if applicable to your trim level. With a second person assisting, remove the OEM bonnet by unbolting the hinge points — typically four bolts per side. Keep hardware for re-use or alignment reference. Offer up the carbon fibre double scoop bonnet to the hinge positions. Do not fully tighten at this stage — leave bolts loose enough to allow fine adjustment. Close the bonnet carefully and check panel gaps on both sides against the front wings and grille surround. Adjust hinge positions as needed for even, symmetrical alignment. Once satisfied with fit and alignment, torque all hinge bolts to factory specification. Reconnect any cables or washer jets previously disconnected. Open and close the bonnet several times to confirm the latch engages cleanly and the bonnet sits flush at all four corners. ⚠ Important: Due to the size, weight distribution and alignment sensitivity of a full bonnet replacement, professional bodyshop installation is strongly recommended. Poor alignment can result in paint damage to adjacent panels. Always use a second person when handling and fitting. Built for Defenders That Stand Apart The Gloss Carbon Fibre Double Scoop Bonnet is one of the most impactful single upgrades you can make to the L663 Defender — visible from every angle, and built to the standard your vehicle deserves. Explore our full Defender L663 collection for matching exterior upgrades. Shop All Defender L663 Upgrades → Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 🔄 30-Day money-back guarantee ✈️ Worldwide shipping via DHL, FedEx, UPS & TNT 📞 +44 203 943 9919 Mon–Fri, 9am–7pm Victorious Automotive is an independent aftermarket accessories retailer. We are not affiliated with, endorsed by, or connected to Land Rover, Jaguar Land Rover (JLR), or any of their subsidiaries. All vehicle names, model codes, and trademarks referenced are used for fitment identification purposes only and remain the property of their respective owners. Always verify compatibility before purchasing. Professional installation is recommended for structural or body panel components.

Victorious · Defender L663 · In-Car Entertainment 11.4" Rear Entertainment Screens for Defender L663 Factory-integrated 1080p HD displays with wireless connectivity for seamless rear-seat entertainment on your 2020+ Defender. L663 2020–2026 Android OS 11.4" 1080p 4GB+64GB Bluetooth Wi-Fi/4G Overview The Defender L663 (2020–2026) is built for adventure, but rear passengers deserve comfort on those longer journeys. These factory-style 11.4-inch rear entertainment screens integrate seamlessly into your cabin, maintaining the original aesthetic while delivering modern connectivity and entertainment options. Each screen runs on a dedicated Android OS platform with 4GB RAM and 64GB onboard storage. The 1080p HD display offers sharp visuals and responsive touch control. Built-in Wi-Fi and 4G connectivity let passengers stream content, check navigation, or stay connected without tethering to the main vehicle system. The lossless Bluetooth module connects to your Defender's head unit or standalone headphones for private audio. The mounting bracket is a 1:1 replica of Land Rover's factory fixture, ensuring a professional installation and perfect alignment with your cabin trim. Global language support means international travel is hassle-free. This is mobile office and entertainment hub on wheels. What's Included 🖥️ 11.4" 1080p Display Crystal-clear HD touchscreen for rear passengers 📱 Android OS System 4GB RAM + 64GB storage with app support 🔧 Factory Mounting Bracket 1:1 replica for perfect fitment and alignment 🌐 Wi-Fi & 4G Built-In Standalone connectivity for streaming and browsing 🎧 Bluetooth Audio Module Lossless quality for headphones or vehicle head unit 🌍 Global Language Support Multi-language interface and screen mirroring ready Product Highlights Factory-integrated design—no aftermarket appearance 1080p HD resolution with responsive touch interface Dedicated 4GB RAM and 64GB storage for smooth performance Independent Wi-Fi and 4G connectivity—no vehicle network required Lossless Bluetooth for premium audio quality Screen mirroring from mobile devices (iOS and Android compatible) 1:1 replica mounting bracket—professional fitment guaranteed Android OS with app ecosystem for entertainment and navigation Suitable for Defender 110 and all 2020+ L663 body styles 30-day money-back guarantee from Victorious Automotive Compatibility Defender Model Year Range Fitment Defender 110 L663 2020–2026 Direct Fit Defender 90 L663 2020–2026 Direct Fit Defender 130 L663 2020–2026 Direct Fit Defender (Pre-2020) 2004–2019 Not Compatible Range Rover Sport / Vogue All years Not Compatible Installation Notes Difficulty: Intermediate | Time: 90–120 minutes | Tools: Trim removal kit, panel popper, standard screwdriver set Power down your Defender and disconnect the negative battery terminal for safety. Remove the rear seat headrest supports and carefully pry away the upper cabin trim using a panel popper. Unclip the factory headrest area covers to expose the mounting points. Align the 1:1 replica bracket with the pre-drilled mounting holes and secure using the provided hardware. Route power and data cables through existing cable channels along the vehicle frame. Connect the display harness to the mounting bracket and test power-up before final reassembly. Reinstall cabin trim, ensuring all clips are fully seated and no cables are pinched. Reconnect the battery and perform a system boot test to confirm full functionality. Configure Wi-Fi/4G settings and pair Bluetooth devices via the Android OS settings menu. Warning: Do not force trim components—Land Rover uses precision-fit clips. If resistance is met, stop and verify alignment. Improper removal can crack cabin panels. Consider professional fitting if you're unfamiliar with Defender interior trim work. Ready to Upgrade Your Rear Cabin? Transform your Defender L663 into a mobile entertainment suite. Your passengers will appreciate the distraction-free, beautifully integrated display system on every journey. Shop Defender L663 Upgrades Use code 22GET20 for 20% off when you buy any 2 Victorious items. 4.9★ 12,300+ Reviews 📞 +44 203 943 9919 ✓ 30-Day Money-Back 🌍 Worldwide Shipping Victorious Automotive is an independent specialist retailer and is not affiliated with Land Rover, Range Rover, Jaguar Land Rover, or any OEM manufacturer. All vehicle names, logos, and trademarks remain the property of their respective owners. Product compatibility is provided for reference only. Always verify fitment with your vehicle identification number (VIN) or consult our sales team before purchase.

Victorious Automotive · Defender L663 · Running Boards & Side Steps Deployable Electric Side Steps – Land Rover Defender L663 110 (2020+) Power-retractable aluminium side steps engineered specifically for the Defender 110 L663 — deploying automatically on door open, retracting flush with the body on close, for a seamless, factory-quality experience every time. Defender L663 2020–2025 Defender 110 Electric Deployable Heavy-Duty Aluminium Plug-and-Play Wiring Anti-Slip Surface OEM-Style Fitment Ground Clearance Preserved Overview The Defender 110 L663 is engineered to sit tall — and that elevated ride height is a core part of what makes it one of the most accomplished and imposing 4x4s available today. Whether it's the standard turbodiesel or the 5.0-litre V8, every variant commands the road by virtue of its stature. But that same stature can make daily entry and exit genuinely cumbersome — for drivers, passengers, and families alike. The step from kerb to cabin is a long one, and over time, it adds up. These Deployable Electric Side Steps are the intelligent answer. Engineered specifically around the Defender 110 L663's rocker panel geometry and OEM mounting architecture, they integrate into the vehicle's existing door trigger circuit and operate entirely automatically. Open any door and the steps extend outward and downward within seconds, providing a wide, textured, anti-slip platform. Close the door and they retract cleanly flush with the body — completely out of sight, out of the way, and out of the vehicle's off-road path. Constructed from heavy-duty aluminium with a corrosion-resistant satin finish, these steps are built for the Defender's real-world environment: muddy lanes, coastal roads, urban streets, and everything between. The plug-and-play wiring harness requires no permanent modifications, no chassis drilling, and no aftermarket control modules. They connect, they work, and they continue to work — silently and reliably — every time you open a door. What's Included 🦶 Side Step Units × 2 Left and right, pre-assembled and ready to mount ⚙️ Electric Motors × 2 One per side, pre-mounted to the step arm 🔌 Plug-and-Play Wiring Harness Door trigger connectors — no cutting or splicing 🔩 Mounting Brackets & Hardware All fixings for OEM rocker panel mounting points 🛡️ Wiring Clips & Conduit For clean, protected cable routing through the sill 📄 Installation Guide Step-by-step printed instructions included Product Highlights Fully automatic operation — deploys and retracts with every door open and close cycle Heavy-duty aluminium construction rated for continuous daily use and real off-road conditions Wide, textured anti-slip step surface for confident footing in all weather Retracts completely flush with the body — ground clearance and off-road geometry fully preserved Plug-and-play wiring taps directly into the factory door trigger circuit No permanent modifications, no drilling to the chassis or rocker panel required Silent motor operation — no grinding, no audible lag, no cabin noise Satin aluminium finish resists corrosion, road salt, mud, and UV degradation Designed exclusively for the Defender 110 L663 — precise OEM mounting point fitment Professional-quality installation achievable in 2–4 hours with basic hand tools Compatibility Model Generation Years Fitment Defender 110 L663 2020–2025 ✓ Direct Fit Defender 110 V8 L663 2021–2025 ✓ Direct Fit Defender 90 L663 2020–2025 Not Compatible Defender 130 L663 2022–2025 Not Compatible Defender (pre-2020) L316 — Not Compatible Engineered for the Defender 110 five-door body only. Compatible across all trim levels including Standard, S, SE, HSE, X, and X-Dynamic. Not suitable for the 90 three-door or 130 six-door variants due to differing rocker panel geometry, wheelbase dimensions, and door configurations. If you are unsure of your specific variant, please contact our team before ordering. Installation Notes ⚡ Medium–Professional · 2–4 Hours · Basic Hand Tools Required Prepare the vehicle. Park on a clean, level surface with all doors closed and the engine off. You will be working beneath and alongside the vehicle, so a flat driveway or workshop floor with good lighting is ideal. Have a jack and axle stands available if additional underbody access is required. Remove the factory rocker sill trims. The lower sill trim panels on the Defender 110 L663 are retained by perimeter clips and require no tools to remove. Work carefully around each clip using a plastic trim removal tool to avoid marking or cracking the panels — you will be refitting these at the end. Mount the step brackets to the rocker panel. Using the supplied bolts and hardware, secure the mounting brackets to the existing OEM threaded fixing points along the underside of the rocker panel. No drilling is required — all fixing points are factory pre-existing locations. Attach the step arm and motor assemblies. Slide the pre-assembled step arm and motor units onto the mounted brackets and secure with the supplied fasteners. Orient each motor inward toward the vehicle sill, ensuring the step arm articulates freely through its full deployment arc before final tightening. Route and connect the wiring harness. Feed the supplied harness through the sill cavity and up to the door jamb area on each side. Connect the plug-and-play connectors to the factory door trigger wiring — no cutting, crimping, or splicing is required. Secure all excess cabling using the included clips and conduit to prevent contact with moving components. Test operation before completing the install. Reconnect the battery, then open each door individually to confirm the corresponding step deploys fully and retracts cleanly on close. Adjust the motor arm deployment angle if needed for clearance. Once satisfied, refit the sill trim panels to complete the installation. Note: We recommend this installation be carried out by a competent and experienced DIYer or a qualified Land Rover specialist. Incorrect wiring harness routing can result in chafing against articulating components over time. If you would prefer professional fitting, our team can recommend a vetted installer in your area — call us on +44 203 943 9919, Monday to Friday, 9am–7pm. Step Up. Without Stepping Down. The Defender was built to go anywhere and look exactly like it can. These electric side steps make sure everyone gets in comfortably — without the vehicle ever compromising its profile when parked, or its capability when the terrain gets serious. They disappear when you don't need them, and reappear the moment you do. Backed by a 30-day money-back guarantee, 4.9★ from 12,300+ verified reviews, and worldwide shipping via DHL, FedEx, UPS and TNT. Shop the Full Defender L663 Collection → Use code 22GET20 for 20% off any two items ⭐ 4.9/5 · 12,300+ reviews 🚚 Worldwide shipping via DHL, FedEx, UPS & TNT ↩️ 30-day money-back guarantee 📞 Expert advice Mon–Fri, 9am–7pm Victorious Automotive is not affiliated with, endorsed by, or connected to Land Rover or Jaguar Land Rover Limited in any way. All vehicle model names, generation codes, and identifiers are referenced solely for product fitment and compatibility identification purposes. All trademarks remain the property of their respective owners.

Victorious Automotive · Defender L663 · Exterior Upgrades Deployable Electric Side Steps – Land Rover Defender 90 L663 (2020–2024+) Motorised steps that extend on door open and retract flush on close — enhancing accessibility without sacrificing ground clearance or the Defender's commanding stance. Defender L663 90 Model Only 2020–2024+ Electric Deployable Auto Retract Matte Black 300kg Load Rated Weather Sealed Direct Fit Overview The Land Rover Defender 90 L663 is built to go further, look bolder, and perform harder than almost anything else on the road or off it. Its raised ride height is an asset on the trail — but for daily use, getting in and out with ease, especially for passengers, can be a genuine inconvenience. That's precisely the problem these Deployable Electric Side Steps are engineered to solve. Designed and fitment-matched exclusively for the Defender 90 L663 (2020 onwards), these motorised steps integrate seamlessly with your vehicle's door trigger signal. The moment a door is opened, the steps extend smoothly and quietly into position. When the doors close, they retract flush to the vehicle body — restoring your ground clearance and keeping the Defender's silhouette exactly as it should be. No permanent protrusions, no compromise on approach angles. Finished in a sleek matte black that pairs naturally with the Defender's factory arches and trim, these steps add a layer of purposeful refinement rather than afterthought. Whether you're loading up for a weekend away, helping children or older passengers aboard, or simply want a cleaner entry experience every day, this is one of the most functional exterior upgrades available for the modern Defender. What's Included 🦶 Side Steps (Pair) Left & right, matte black finish ⚙️ Electric Motors One per side, heavy-duty rated 🔩 Mounting Brackets Vehicle-specific, pre-formed steel 🔌 Wiring Harness Full plug-and-play loom included 🧠 Control Module Door-signal logic controller 🔧 Hardware Kit All fixings, bolts & fasteners 📋 Installation Guide Step-by-step printed instructions Product Highlights Automatically extends when either front or rear door is opened Auto-retracts flush on door close — zero permanent ground clearance loss Model-specific fitment engineered for Defender 90 L663 only Heavy-duty construction rated to 300kg per step Weather-sealed motors and control unit for all-season reliability Matte black finish matched to factory arches and cladding Quiet, smooth motor operation — minimal deployment noise Preserves aerodynamics and approach angle when retracted Wiring harness connects to existing door signal circuit — no modification required Full fitting kit included — no additional parts needed Compatibility Model Code Years Fitment Defender 90 L663 2020, 2021, 2022, 2023, 2024+ Direct Fit Defender 110 L663 2020–2024+ Not Compatible Defender 130 L663 2022–2024+ Not Compatible Defender 90 (Classic) Pre-L663 Pre-2020 Not Compatible Installation Notes Installation Overview — Difficulty: Intermediate · Estimated Time: 3–5 Hours Raise and safely support the vehicle to access the underside along the sill area. Position and bolt the vehicle-specific mounting brackets to the chassis using the hardware provided — no drilling required on 90 L663 models. Attach the electric motors and step arms to the mounted brackets and secure all fixings to torque spec. Route the wiring harness from each motor through the sill channel toward the control module mounting location. Connect the control module to your vehicle's door signal wire (identified in the installation guide) and to a switched 12V power source. Test deployment and retraction on both sides before final cable management and tie-off. Lower the vehicle, confirm ground clearance is unaffected in the retracted position, and verify smooth step operation through multiple door cycles. ⚠ Professional Installation Recommended. This product requires connection to your vehicle's door signal circuit and 12V power supply. Incorrect wiring may affect vehicle electronics. If you are not confident working with automotive electrics, we strongly recommend professional fitting by a qualified auto electrician or 4x4 specialist. Built for the Defender. Backed by Victorious. Every product we offer is selected for fit, finish, and function — not just aesthetics. These Deployable Electric Side Steps are one of the most practical upgrades you can make to the Defender 90, and they're engineered to last as long as the vehicle itself. Shop All Defender L663 Accessories Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 📦 Worldwide Shipping via DHL, FedEx, UPS & TNT 🔄 30-Day Money-Back Guarantee 📞 +44 203 943 9919 Mon–Fri, 9am–7pm Victorious Automotive is an independent aftermarket accessories retailer. We are not affiliated with, endorsed by, or representing Land Rover, Jaguar Land Rover (JLR), or any of their subsidiaries. All vehicle names, model codes, and trademarks are the property of their respective owners and are referenced solely for fitment compatibility purposes.

Victorious Automotive · Defender L663 · Interior Trim Full Carbon Fibre Interior Replacement Kit – Land Rover Defender L663 90 & 110 A complete set of genuine carbon fibre OEM-replacement trim panels, engineered to transform your Defender's cabin with motorsport-grade precision and a finish that factory trim simply cannot match. Defender L663 2020–2024+ Real Carbon Fibre 90 & 110 Full Replacement Kit High-Gloss Finish OEM Fitment UV-Resistant Interior Upgrade Overview The Land Rover Defender L663 is one of the most capable and characterful vehicles on the road today — a machine built with serious intent, from its all-terrain hardware to its purposeful, driver-focused cabin. But for those who push every detail further, the standard interior trim leaves room for something bolder. That's precisely where this kit begins. This Full Carbon Fibre Interior Replacement Kit is engineered specifically for the Defender 90 and 110 (L663, 2020 onwards). Every component is crafted from 100% real woven carbon fibre — not a vinyl wrap, not an overlay, not a printed film. Each piece is a full OEM-style replacement panel, designed to locate directly onto factory mounting points with the same precision you'd expect from Land Rover's own engineers. The result is a seamless, factory-integrated finish that elevates the interior without compromising its structural integrity. The high-gloss, UV-resistant lacquer protects the carbon weave against fading and surface abrasion over time, ensuring the finish stays as sharp in five years as it does on day one. Whether you're building a lifestyle-focused Defender for daily use or a more track-inspired specification, this kit delivers the kind of tactile and visual upgrade that sets a vehicle apart from every other L663 on the road. What's Included 🏎️ Steering Wheel Trim Carbon fibre insert panel for the steering wheel surround 📐 Dashboard End Trim Panels Left & right — full replacement, not adhesive covers 🪟 Window Switch Surrounds Precision-cut frames replacing factory switch bezels ⚙️ Gear Selector Surround Frames the rotary gear selector with carbon detailing 🖤 Centre Console Surround Plate Full-replacement console surround panel in carbon fibre 🔩 Fitting Hardware All mounting clips and fasteners included Product Highlights 100% real woven carbon fibre construction — no wraps, films or printed overlays High-gloss UV-resistant lacquer finish — fade-proof and scratch-resistant long term Full OEM-style replacement panels — not stick-on covers or adhesive overlays Designed to fit factory mounting points on Defender 90 and 110 models Motorsport-grade weave pattern with a consistent, premium visual across every panel Lightweight carbon construction — adds visual weight without adding physical mass Compatible with all factory trim levels including Standard, S, SE, X and X-Dynamic All hardware included — no additional parts required for a full installation Each panel is individually quality-checked before dispatch Exclusive to Victorious Automotive — not available through general retail channels Compatibility Vehicle Code Years Trim Levels Fit Defender 90 L663 2020–2024+ Standard, S, SE, X, X-Dynamic Direct Fit Defender 110 L663 2020–2024+ Standard, S, SE, X, X-Dynamic Direct Fit Defender 130 L663 2022–2024+ All Verify Before Purchase Defender 90/110 (Aftermarket Console) L663 Any Any Not Compatible Defender 90/110 (Pre-2020 Classic) L316 Pre-2016 All Not Compatible Installation Notes 🛠️ Difficulty: Intermediate  |  Estimated Time: 2–4 Hours  |  Tools: Trim removal tools, microfibre cloths Park on a level surface and allow the interior to reach ambient temperature before beginning. Cold trim panels are more brittle and prone to stress marks during removal. Using a plastic trim removal tool, carefully detach each factory panel in the order listed in the included fitting guide — beginning with the dashboard end trims and working inward toward the centre console. Set factory trim aside in a safe location. These should be retained in the event of a warranty claim or future resale. Test-fit each carbon fibre replacement panel before final installation to confirm correct clip alignment and panel orientation. Locate each panel onto the factory mounting points and press firmly until all clips engage. Do not force any panel — resistance indicates a misalignment that should be corrected before applying further pressure. Fit the gear selector surround and window switch surrounds last, ensuring no wiring harnesses are pinched beneath the panels. Wipe down all installed panels with a dry microfibre cloth to remove any fingerprints from the lacquer surface before use. ⚠ Professional Installation Recommended. While this kit is designed for direct OEM replacement, trim removal on the L663 involves plastic clips that may be fragile on older vehicles. If you are not confident working with interior trim components, we recommend installation by a Land Rover specialist or approved trim technician to avoid damage to surrounding panels or mounting points. Refined. Reshaped. Reimagined. Few upgrades transform a Defender's cabin as completely as replacing the factory trim with genuine carbon fibre. This kit gives you the material quality of a full custom build, with the fitment precision of an OEM component — and it's available exclusively through Victorious Automotive. Shop All Defender L663 Upgrades Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 🔄 30-Day money-back guarantee 🌍 Worldwide shipping via DHL, FedEx, UPS & TNT 📞 +44 203 943 9919 Mon–Fri, 9am–7pm Victorious Automotive is an independent aftermarket accessories retailer. This product is not manufactured by, affiliated with, endorsed by, or approved by Land Rover, Jaguar Land Rover Limited (JLR), or any of their subsidiaries. All vehicle names, model codes, and trademarks referenced are the property of their respective owners and are used for fitment identification purposes only. Always verify compatibility with your specific vehicle specification before purchase.

جراب إضاءة السقف من ألياف الكربون لسيارة ديفندر 2020 الجديدة. هذا التجميع سيميز المدافع الخاص بك عن الباقي. جراب سقف من ألياف الكربون مصنوع يدويًا من ألياف الكربون فائق السطوع وناعم للمدافع الجديد 2020. يتميز هذا بنهج غير مدمر للتثبيت وعدم وجود أخطاء عند التثبيت. يتم تشغيله مباشرة من صندوق المصهر ويتم توصيله عبر جهاز التحكم عن بعد اللاسلكي - مما يحافظ على مظهر مفاتيح وأجهزة القياس الأصلية. مصنوعة من ألياف الكربون الحقيقية. مصابيح LED فائقة السطوع وذات مواصفات عالية. يناسب المدافع 90 و المدافع 110 تثبيت: تركيب جراب السقف الفعلي سهل للغاية. تأكد من أن السطح نظيف وقم بتركيبه باستخدام شريط 3M للسيارات. مطلوب خبرة DIY للقيام بأسلاك الأضواء. ملحوظة: هذا المنتج مصنوع من ألياف الكربون الحقيقية ومصنوع يدويًا. يمكن أن تكون العيوب الصغيرة مرئية. ملحوظة: التركيب على مسئولية العميل.

هذه مجموعة قطع غيار داخلية من خشب الخوخ لسيارة Defender 90/110 تأتي المجموعة مع قطع غيار داخلية بديلة لـ؛ - 4x أغطية قولبة للأبواب - خشب الخوخ - 3X أغطية لمقابض الأبواب - خشب الخوخ - الكونسول الوسطي - خشب الخوخ - 2x مقابض أمامية ملاحظة: قد تتغير العناصر المذكورة أعلاه اعتمادًا على المتغير المحدد. يرجى التأكد من تحديد البديل مع طراز السيارة لديك. ملحوظة: يرجى تحديد محرك اليد اليسرى أو محرك اليد اليمنى.

Victorious Automotive · Defender L663 · Exterior Upgrades Forged Carbon Hood Vents (OCTA Design) – Land Rover Defender L663 2020+ A precision-engineered forged carbon replacement for the Defender's bonnet vent slats — delivering unmistakable visual depth and improved thermal performance in the OCTA signature pattern. Defender L663 2020–2026 Forged Carbon OCTA Design High Gloss Finish Direct Fit Hood / Bonnet Exterior Overview The Land Rover Defender L663 is a vehicle that wears its character on the outside — every panel, vent, and graphic is a statement of purpose. For owners who want to push that character further, the factory black plastic bonnet vent slats represent one of the most visible and rewarding upgrade opportunities on the entire vehicle. It's a high-visibility detail that draws the eye immediately, and the right material makes all the difference. These forged carbon hood vents in the OCTA design bring genuine material quality to that focal point. Forged carbon — unlike standard woven carbon fibre — produces a fluid, marbled pattern unique to every piece. Paired with a high gloss black insert and formed to match the existing vent geometry precisely, the result is something that looks factory-correct in fitment while reading as unmistakably premium in finish. The OCTA pattern adds structured visual texture that complements the Defender's angular, architectural design language. Beyond aesthetics, the open vent design maintains and supports airflow through the bonnet, assisting cooling efficiency under the hood during demanding driving conditions. These vents are a direct drop-in replacement for the standard slats — no modification, no drilling, no guesswork. For Defender owners who care about the details, this is exactly the kind of upgrade that rewards close attention. What's Included 🔲 Forged Carbon Hood Vents Full set — OCTA design pattern, high gloss finish ⬛ High Gloss Black Insert Pre-fitted contrast insert included with each vent 🔧 Fitting Hardware All necessary clips and retention hardware 📋 Installation Guide Step-by-step fitting reference included Product Highlights Genuine forged carbon construction — no printed wraps or faux finishes Unique marbled pattern on every set — no two pieces are identical OCTA geometric design complements Defender's bold exterior architecture High gloss clear coat for long-term UV and weather resistance High gloss black insert provides sharp contrast definition Direct OEM replacement — slots into factory vent mounting positions No drilling, cutting, or permanent modification required Maintains original bonnet ventilation and airflow properties Significantly lighter than factory plastic equivalent Pairs perfectly with the matching Forged Carbon Side Vents Compatibility Vehicle Code Year Range Fitment Land Rover Defender 90 L663 2020–2026 Direct Fit Land Rover Defender 110 L663 2020–2026 Direct Fit Land Rover Defender 130 L663 2022–2026 Direct Fit Range Rover Sport L461 / L494 All Years Not Compatible Range Rover Vogue L460 / L405 All Years Not Compatible Range Rover Velar L560 All Years Not Compatible Classic Defender L316 Pre-2020 Not Compatible Installation Notes 🔧 Difficulty: Easy  ·  ⏱ Estimated Time: 20–40 Minutes  ·  🛠 Tools Required: Trim removal tool, clean microfibre cloth Ensure the bonnet/hood is fully open and supported. Allow the engine bay to cool completely before beginning work. Using a plastic trim removal tool, carefully release the retaining clips securing the existing factory vent slats. Work gently from one end to avoid cracking the surrounding trim. Remove the original vent slats fully and set aside. Clean the mounting channels with a microfibre cloth to remove any dust or debris. Align the new forged carbon hood vents with the factory mounting positions. Verify orientation — the OCTA design is directional. Press firmly and evenly along the length of each vent until all retaining clips engage with an audible click. Do not force — if resistance is felt, recheck alignment. Close the bonnet and inspect from the front of the vehicle to confirm even seating and flush fitment on both sides. ⚠ Note: Professional installation is recommended if you are unfamiliar with trim removal on the Defender L663. Incorrect removal of factory clips may cause damage to surrounding bodywork. Victorious Automotive accepts no liability for damage incurred during installation. Looking to complete the look? Pair these hood vents with the Forged Carbon Side Vents for the Defender L663 → Complete Your Defender Build Browse the full Victorious range of exterior upgrades for the Defender L663 — from forged carbon to gloss black trim, every piece is engineered to fit and finish like it belongs. Shop Defender L663 Collection Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 📦 Worldwide Shipping via DHL, FedEx, UPS & TNT ↩ 30-Day Money-Back Guarantee 📞 +44 203 943 9919 Mon–Fri, 9am–7pm Victorious Automotive is an independent aftermarket accessories retailer. This product is not manufactured by, affiliated with, endorsed by, or associated with Land Rover, Jaguar Land Rover Limited (JLR), or any of their subsidiaries. All vehicle names, model codes, and trademarks referenced are the property of their respective owners and are used solely for the purpose of fitment identification.

نسختنا 2! - جراب إضاءة السقف من ألياف الكربون لسيارة ديفندر 2020 الجديدة. هذا التجميع سيميز المدافع الخاص بك عن الباقي. جراب سقف من ألياف الكربون مصنوع يدويًا من ألياف الكربون فائق السطوع والانسيابية للمدافع الجديد 2020. يتميز هذا بنهج غير مدمر للتثبيت وعدم وجود أخطاء عند التثبيت. يتم تشغيله مباشرة من صندوق المصهر ويتم توصيله عبر جهاز التحكم عن بعد اللاسلكي - مما يجعل مفاتيح وأجهزة القياس تبدو أصلية. مصنوعة من ألياف الكربون الحقيقية. مصابيح LED فائقة السطوع وذات مواصفات عالية. يناسب المدافع 90 و المدافع 110 تثبيت: تركيب جراب السقف الفعلي سهل للغاية. تأكد من أن السطح نظيف وقم بتركيبه باستخدام شريط 3M للسيارات. مطلوب خبرة DIY للقيام بأسلاك الأضواء. ملحوظة: هذا المنتج مصنوع من ألياف الكربون الحقيقية ومصنوع يدويًا. يمكن أن تكون العيوب الصغيرة مرئية. ملحوظة: التركيب على مسئولية العميل. طَرد 1. كل عنصر لديه تعبئة مستقلة 2. داخل كيس البولي ايثيلين، خارج علبة كرتون، التعبئة والتغليف ذات نوعية جيدة تجعل البضائع أكثر أمانا

فقط في! جراب إضاءة السقف من ألياف الكربون لسيارة ديفندر 2020 الجديدة. هذا التجميع سيميز المدافع الخاص بك عن الباقي. جراب سقف من ألياف الكربون مصنوع يدويًا من ألياف الكربون فائق السطوع وناعم للمدافع الجديد 2020. يتميز هذا بنهج غير مدمر للتثبيت وعدم وجود أخطاء عند التثبيت. يتم تشغيله مباشرة من صندوق المصهر ويتم توصيله عبر جهاز التحكم عن بعد اللاسلكي - مما يحافظ على مظهر مفاتيح وأجهزة القياس الأصلية. مصنوعة من ألياف الكربون الحقيقية. مصابيح LED فائقة السطوع وذات مواصفات عالية. يناسب المدافع 90 و المدافع 110 تثبيت: تركيب جراب السقف الفعلي سهل للغاية. تأكد من أن السطح نظيف وقم بتركيبه باستخدام شريط 3M للسيارات. مطلوب خبرة DIY للقيام بأسلاك الأضواء. ملحوظة: هذا المنتج مصنوع من ألياف الكربون الحقيقية ومصنوع يدويًا. يمكن أن تكون العيوب الصغيرة مرئية. ملحوظة: التركيب على مسئولية العميل.

Victorious Automotive · Defender L663 · Interior Upgrades OEM-Style In-Console Refrigerator – Defender L663 (2020+) Keep drinks and snacks chilled on every journey with a plug-and-play refrigerator engineered to integrate seamlessly into the Defender L663 front centre console. Defender L663 2020–2026 OEM-Style Fitment Dual-Mode Cooling 12V Plug & Play LED Illuminated Quiet Operation Interior Upgrade Overview The Land Rover Defender L663 is built for those who refuse to compromise — a vehicle that performs at the extreme while delivering a cabin that rivals far more road-focused luxury SUVs. Whether you're traversing remote terrain for days at a time or commuting across the city, the quality of your in-cabin experience matters. That attention to detail is exactly what this upgrade is designed to honour. This OEM-style refrigerator has been engineered specifically for the Defender L663 (2020 onwards), designed to drop into the front centre console as though it were always there. With dual-mode cooling — standard chill for everyday refreshments and a deep-freeze setting for longer expeditions — this unit delivers real-world utility without sacrificing the clean, premium aesthetic the Defender interior demands. The 12V plug-and-play connection means no complicated wiring, no ECU coding, and no permanent modifications to your vehicle. Quiet enough to go unnoticed on the move, LED-lit for effortless access at night, and finished to a standard that matches the Defender's own interior quality — this is the kind of upgrade that simply makes sense. What's Included ❄️ In-Console Refrigerator Unit OEM-style unit designed for Defender L663 centre console 🔌 Power Connector & Wiring Kit 12V plug-and-play harness, no coding required 📋 Installation Guide Step-by-step instructions for professional fitting Product Highlights OEM-style fitment integrates perfectly into the front centre console — no gaps, no compromise Dual-mode cooling system with standard chill and deep-freeze settings for all journey types 12V plug-and-play connection — powers up without ECU coding or permanent wiring changes LED internal lighting ensures clear visibility of contents day or night Low-noise motor operates quietly in the background — no cabin disruption on longer drives Engineered specifically for Defender L663 — not a universal fit adapted to work Holds drinks, snacks, and small provisions — ideal for overlanding, road trips, or daily use Retains original centre console appearance when closed — discreet and clean Durable construction with materials matched to the Defender's interior quality standards Straightforward installation process — completed in a single session by a competent fitter Compatibility Vehicle Code Years Fitment Notes Defender 90 L663 2020–2026 Direct Fit Check for factory fridge option before ordering Defender 110 L663 2020–2026 Direct Fit Check for factory fridge option before ordering Defender 130 L663 2022–2026 Direct Fit Confirm centre console configuration before ordering Defender L663 (Factory Fridge Fitted) L663 2020–2026 Not Compatible Unit already present — not required Defender L316 (Classic) L316 Pre-2016 Not Compatible Different platform and console architecture Range Rover Sport L461 L461 2022–2026 Not Compatible Different console design — not interchangeable Range Rover Vogue L460 L460 2022–2026 Not Compatible Different console design — not interchangeable Installation Notes 📐 Difficulty: Intermediate  |  ⏱ Estimated Time: 1–2 Hours  |  🔧 Professional Installation Recommended Remove the existing front centre console insert carefully, retaining all clips and trim pieces for reassembly. Test-fit the refrigerator unit into the console void to confirm alignment and clearance before making any connections. Route the 12V wiring harness neatly through the console, connecting to the vehicle's 12V accessory supply as directed in the installation guide. Secure the refrigerator unit within the console cavity using the provided hardware, ensuring no movement or rattle. Reinstate all trim panels and clips, checking that the console closes cleanly and the refrigerator door opens without obstruction. Power on the vehicle and test both cooling modes — standard chill and deep-freeze — to confirm correct operation before completing the installation. ⚠ Important: Do not install this unit in vehicles already factory-equipped with a refrigerator. Always verify your Defender's specification before ordering. Professional installation is strongly recommended to ensure secure fitment, correct power routing, and to protect your vehicle's interior trim. Victorious Automotive accepts no liability for damage caused by incorrect DIY installation. Watch the installation and overview video above Upgrade Your Defender the Right Way Every Defender owner deserves accessories that match the ambition of the vehicle. This refrigerator is the kind of upgrade you'll use on every drive — functional, discreet, and built to the standard your L663 deserves. Shop All Defender L663 Accessories 🏷 Use code 22GET20 — 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 🔄 30-Day money-back guarantee ✈️ Worldwide shipping via DHL, FedEx, UPS & TNT 📞 +44 203 943 9919 Mon–Fri, 9am–7pm Victorious Automotive is an independent aftermarket accessories retailer. This product is not manufactured by, affiliated with, endorsed by, or approved by Land Rover, Jaguar Land Rover (JLR), or any of their subsidiaries. All vehicle names, model codes, and trademarks referenced are the property of their respective owners and are used for fitment identification purposes only. Always verify compatibility with your specific vehicle specification before purchase.

Victorious Automotive · Defender L663 · Exterior Styling Gloss Black Exterior Pack – Land Rover Defender 90 / 110 / 130 (L663) 2020+ A complete de-chrome styling kit that replaces key silver and grey exterior trims with a deep, high-gloss black finish — delivering a factory-blacked-out presence without modification. Defender L663 2020–2025+ 90 · 110 · 130 ABS Construction UV-Resistant Gloss No Drilling Required OEM Fitment De-Chrome Upgrade Overview The Land Rover Defender L663 is a vehicle that rewards attention to detail. From its squared-off silhouette to its exposed bolt architecture, every element of the Defender's design makes a deliberate visual statement — and the exterior trim plays a critical role in defining its character. The factory silver and grey accents, while functional, can dilute the impact of an otherwise aggressive, purposeful build. The Victorious Gloss Black Exterior Pack for the Defender 90, 110, and 130 is engineered as a complete de-chrome solution. Rather than individual pieces purchased separately, this pack delivers a cohesive, coordinated transformation across the front and rear of the vehicle — bumper trims, grille surrounds, fog light housings, and rear inserts — all finished in the same deep, mirror-quality gloss black. The result is a uniform, blacked-out aesthetic that reads as intentional and refined rather than aftermarket. Whether you're building a stealth-focused urban Defender or a commanding overland machine, this pack integrates seamlessly with black alloys, roof accessories, and carbon fibre accents to elevate the overall finish of your build without touching the factory mounting architecture. What's Included 🖤 Front Bumper Trims Replaces factory silver lower front bumper accents 🖤 Rear Bumper Trims Gloss black finish to match front for cohesive styling 🖤 Fog Light Trims Surrounds front fog light housings in matching gloss black 🖤 Rear Trim Inserts Gloss black inserts for the rear tailgate surround area 🖤 Front Grille Trim Replaces chrome/silver grille surround with gloss black finish 🖤 Front Grille Lower Trim Panel Lower fascia panel in deep gloss black for a unified front end Kit contents may vary slightly depending on Defender body style: 90 / 110 / 130. Please confirm your model at checkout or contact our team. Product Highlights OEM-style precision fitment — uses original factory mounting points throughout Deep gloss black UV-resistant finish — colour-stable and weather-protected year-round High-quality ABS construction — lightweight, impact-resistant, and built to last No drilling, cutting, or modification required — fully reversible installation Replaces factory silver and grey trims with a coordinated all-black aesthetic Complete front-to-rear coverage — bumpers, grille, fog lights, and rear inserts Pairs seamlessly with black alloys, roof rails, and carbon fibre exterior accessories Cohesive finish that reads as a factory-spec black pack rather than a retrofit Available across all L663 body styles — Defender 90, 110, and 130 Professional installation recommended for perfect panel alignment and finish Compatibility Vehicle Model Code Years Trim Levels Fitment Defender 90 L663 2020–2025+ S, SE, X-Dynamic, X, V8 Direct Fit Defender 110 L663 2020–2025+ S, SE, X-Dynamic, X, V8 Direct Fit Defender 130 L663 2020–2025+ SE, X-Dynamic, X Direct Fit Defender 90/110/130 – Factory Black Pack L663 2020–2025+ All Not Required Defender L316 (Pre-2020) L316 Pre-2020 All Not Compatible If your Defender came factory-equipped with the OEM Black Pack option, exterior trims may already be gloss black. Contact our team on +44 203 943 9919 if you are unsure of your vehicle's specification. Installation Notes 🔧 Difficulty: Easy to Moderate  ·  Estimated Time: 2–3 Hours Clean all factory trim surfaces thoroughly with an alcohol-based prep solution to remove wax, grease, and debris before beginning. Carefully remove the existing factory silver or grey trim pieces using plastic trim removal tools — avoid metal tools that may scratch surrounding bodywork. Test-fit each gloss black replacement trim to the factory mounting points before final fitment to confirm alignment and seating. Clip or bolt each component into position using the original factory fixings — no additional hardware, drilling, or adhesive is required. Apply light pressure along all edges once fitted to ensure all clips and retention points are fully engaged. Step back and inspect alignment across all panels before completing the install — minor adjustments are easiest made before any rubber trim or weather seals are refitted. ⚠ Installation Note: Professional installation is recommended to ensure perfect panel gap alignment and to avoid damage to surrounding paintwork. This product is not designed for vehicles that left the factory with the OEM Black Pack specification, as those trims are typically already gloss black and the replacement pieces may not achieve the same fitment quality. Black It Out. Level It Up. The Victorious Gloss Black Exterior Pack gives your Defender the commanding, factory-style blacked-out presence it deserves — without compromise and without modification. Every piece is engineered to the same standard you'd expect from the vehicle itself. Shop All Defender L663 Accessories Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 📦 Worldwide Shipping via DHL, FedEx & UPS ↩ 30-Day Money-Back Guarantee 📞 Mon–Fri 9am–7pm +44 203 943 9919 Victorious Automotive is an independent aftermarket accessories retailer. This product is not manufactured by, affiliated with, or endorsed by Land Rover, Jaguar Land Rover (JLR), or any of their subsidiaries. All vehicle names, model codes, and trademarks are the property of their respective owners and are referenced solely for fitment identification purposes.

Victorious Automotive · Defender L663 · Exterior Styling Premium Gloss Black Wheel Flares & Arch Extensions – Land Rover Defender 110 L663 (2020+) Wide-body stance and bold kerb presence engineered specifically for the L663 Defender 110 — in a deep, UV-protected gloss black finish that commands attention from every angle. Defender L663 2020–2025+ Gloss Black ABS Plastic Set of 4 OEM-Style Fit No Drilling Required All Trim Levels Overview The Land Rover Defender 110 L663 is a vehicle that demands accessories worthy of its character — purposeful, robust, and unapologetically bold. Whether you're running the Defender in its standard form or have already begun tailoring it to your taste, the wheel arches are one of the most visually dominant features on the body. They're what give the Defender its planted, wide-track posture — and that's precisely why upgrading them makes such a dramatic difference. These Victorious Premium Gloss Black Wheel Arch Flares are precision-moulded to follow the exact contours of the L663 bodywork, integrating cleanly with the factory panel lines for a look that feels considered rather than bolted-on. Manufactured from heavy-duty ABS plastic and finished in a deep, showroom-quality gloss black, they add instant visual width and definition without compromising the Defender's distinctive silhouette. Beyond aesthetics, these arch flares serve a practical purpose. They extend outward coverage over your tyres, shielding the paintwork, sills, and lower body from stone chips, road debris, and mud thrown up under hard driving conditions — on road or off. A straightforward bond-on installation means there's no need to drill into the body, and the result is an upgrade that looks factory-specified and performs accordingly. What's Included 🖤 Front Wheel Arch Flares × 2 Left & right, precision-moulded for L663 front arches 🖤 Rear Wheel Arch Flares × 2 Left & right, matched profile for seamless rear fitment 🔧 Mounting Hardware Clips or automotive-grade adhesive tape included (design-dependent) 📋 Fitting Instructions Step-by-step guide for clean, confident installation Product Highlights Deep gloss black finish with UV-resistant coating to prevent fading and dulling over time Heavy-duty ABS plastic construction — lightweight yet highly resistant to impact and weathering Precision-moulded to the exact contours of the L663 Defender 110 body panels Wide-body aesthetic adds visual stance and presence without structural modification No drilling required — bond-on fitment preserves factory bodywork integrity Provides practical protection against stone chips, mud splash, and road debris OEM-style integration that looks at home on any factory or lightly modified Defender Compatible with all L663 Defender 110 trim levels including V8 and X-Dynamic Gloss finish complements dark factory trim, black pack options, and aftermarket detailing Full set of four arches included — front and rear, both sides, ready to fit Compatibility Model Code Year Range Trim Level Fitment Defender 110 L663 2020–2025+ S Direct Fit Defender 110 L663 2020–2025+ SE Direct Fit Defender 110 L663 2020–2025+ X-Dynamic SE Direct Fit Defender 110 L663 2020–2025+ X Direct Fit Defender 110 L663 2020–2025+ V8 / V8 Carpathian Direct Fit Defender 90 L663 2020–2025+ All Trims Not Compatible Defender 130 L663 2022–2025+ All Trims Not Compatible Defender 110 (Factory Extended Arches) L663 2020–2025+ Pre-fitted Extended Arches Not Compatible Installation Notes 🔧 Difficulty: Beginner–Intermediate  ·  Estimated Time: 45–90 Minutes  ·  No Drilling Required Thoroughly clean and degrease the surface of each wheel arch using an isopropyl alcohol wipe or panel wipe solution. Remove all wax, polish, and road film residue. Dry all surfaces completely. Allow to reach ambient temperature — avoid fitting in direct sunlight or temperatures below 10°C for best adhesive performance. Dry-fit each arch flare into position before committing, confirming alignment with panel lines and wheel arch edges on all four corners. Apply the included mounting hardware — either automotive-grade adhesive tape or clips — as directed in the included fitting guide. Press firmly and hold for 30–60 seconds on each section. Allow full cure time before driving. For adhesive-backed fitments, 24 hours at room temperature is recommended before exposing the vehicle to water or harsh conditions. ⚠ Important: Professional installation is recommended for optimal panel alignment and to ensure long-term adhesion. Fitting to wet, cold, or contaminated surfaces may compromise bond strength. These flares are designed for the standard L663 Defender 110 arch profile — do not attempt fitment on vehicles already equipped with factory extended or aftermarket arches. Go Wider. Go Bolder. Go Victorious. The Defender 110 deserves accessories built to match its ambition. These gloss black wheel arch flares deliver the stance, the finish, and the protection your L663 deserves — designed and curated by specialists who drive these vehicles too. Shop All Defender L663 Accessories Use code 22GET20 for 20% off when you buy any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 🔁 30-Day money-back guarantee ✈️ Worldwide shipping via DHL, FedEx & UPS 📞 +44 203 943 9919 Mon–Fri, 9am–7pm Victorious Automotive is an independent aftermarket accessory retailer. This product is not manufactured by, affiliated with, endorsed by, or approved by Land Rover, Jaguar Land Rover Limited (JLR), or any of their subsidiaries. All vehicle names, model codes, and trademarks referenced are used for fitment identification purposes only and remain the property of their respective owners. Always verify compatibility with your specific vehicle specification prior to purchase.

هذا جزء داخلي من قطع الغيار باللون الأسود اللامع لسيارة Defender 110. تأتي المجموعة مع قطع غيار داخلية بديلة لـ؛ - 4x أغطية قولبة للأبواب - أسود لامع - 3 أغطية لمقبض الباب - أسود لامع - الكونسول الوسطي - أسود لامع - غطاء عجلة القيادة - أسود لامع - 2x مقابض أمامية ملحوظة: يرجى تحديد محرك اليد اليسرى أو محرك اليد اليمنى.

استبدال مباشر للمصابيح الخلفية للديفندر L663 2020 إلى اللون الأسود المدخن. نمط تصنيع المعدات الأصلية ظلام دامس أسلوب المدافع x

Victorious Automotive · Defender L663 · Exterior Styling Forged Carbon Side Vents – Defender L663 2020+ (OCTA Design) Transform your Defender's flanks with OCTA-inspired forged carbon side vents — a direct-fit upgrade that delivers a genuinely purposeful visual statement in one of motoring's most distinctive materials. Defender L663 2020–2026 Forged Carbon OCTA Design Direct Fit Exterior Styling High Gloss Black Insert Set of Two Overview The Land Rover Defender L663 is one of the most recognisable vehicles on the road — a modern reinterpretation of an icon that carries real presence wherever it goes. For owners who want to push that presence further, the details matter. The factory side vents are functional and well-proportioned, but they represent an obvious opportunity to introduce a material with genuine character. These forged carbon side vents are modelled on the design language introduced with the Defender OCTA — Land Rover's most extreme factory expression of the L663 platform. Forged carbon, unlike woven carbon fibre, offers a fluid, almost organic texture that varies subtly across each panel. No two pieces look identical, which gives the material an exclusivity that sits perfectly alongside the Defender's utilitarian premium aesthetic. The surround is finished in forged carbon, complemented by a high gloss black insert that maintains visual depth without competing for attention. Engineered as a direct replacement for the standard black side vents, fitment is clean and precise. Whether you're building a full OCTA-inspired specification or simply elevating one detail at a time, these vents deliver a result that looks entirely factory-intentional — because the design reference is exactly that. What's Included 🪟 Forged Carbon Side Vent (Left) Direct replacement for driver-side factory vent 🪟 Forged Carbon Side Vent (Right) Direct replacement for passenger-side factory vent 📋 Fitment Hardware All necessary fixings included for installation 📄 Installation Guide Step-by-step reference for a clean, accurate fit Product Highlights Forged carbon surround with distinctive organic fibre texture — no two pieces identical Inspired by the Defender OCTA factory design language for an authentic, intentional look High gloss black insert provides visual contrast and depth without distracting from the carbon Direct OEM replacement fitment — no cutting, drilling, or modification required Lightweight construction adds visual upgrade without adding meaningful mass Improves airflow characteristics alongside the aesthetic enhancement Precision-moulded to match original vent aperture dimensions exactly UV-resistant clear coat finish protects the carbon surface from fading and yellowing Complements forged carbon bonnet vents, mirror caps, and other OCTA-spec accessories Supplied as a matched pair to ensure consistent appearance on both sides of the vehicle Compatibility Model Code Year Range Trim Fitment Defender 90 L663 2020–2026 All Trims Direct Fit Defender 110 L663 2020–2026 All Trims Direct Fit Defender 130 L663 2022–2026 All Trims Direct Fit Defender OCTA L663 2024–2026 OCTA Direct Fit Defender L316 L316 Pre-2020 All Trims Not Compatible Range Rover Sport L461 / L494 All Years All Trims Not Compatible Range Rover Vogue L460 / L405 All Years All Trims Not Compatible Installation Notes Difficulty: Moderate  ·  Estimated Time: 45–90 Minutes  ·  Tools Required: Trim removal tools, panel clips Ensure the vehicle is parked on a level surface and the relevant body panels are clean and cool to the touch before beginning work. Using a trim removal tool, carefully release the factory side vent clips along the outer edge, working from one end to avoid cracking the surrounding bodywork. Gently pull the existing vent panel away from the body, disconnecting any retaining tabs at the rear of the unit without forcing the fit. Inspect the aperture and clean any residue from the mounting points to ensure the new vent seats flush against the body surface. Align the forged carbon vent into the aperture, pressing evenly along the perimeter until all clips engage with a firm, audible click. Repeat the process on the opposite side, then step back to verify both vents sit symmetrically and flush with the surrounding bodywork. Note: Professional installation is recommended to ensure optimal fit, finish, and to avoid any risk of damage to surrounding bodywork or trim. Clip alignment is critical — do not force the panel if resistance is felt before all tabs are correctly seated. Complete Your OCTA Build These side vents are designed to work as part of a cohesive exterior upgrade. For the full OCTA-inspired appearance, pair them with our forged carbon bonnet hood vents — the same material, the same finish, and the same design reference across both panels. Browse the full Defender L663 collection to explore further exterior and interior upgrade options. Upgrade Your Defender L663 Today Free worldwide shipping via DHL, FedEx, UPS & TNT. Backed by our 30-day money-back guarantee and trusted by over 12,300 verified Land Rover owners. Shop Defender L663 Accessories Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 🌍 Worldwide Shipping via DHL, FedEx, UPS & TNT ↩️ 30-Day Money-Back Guarantee 📞 Mon–Fri 9am–7pm · +44 203 943 9919 Victorious Automotive is an independent aftermarket accessories retailer and is not affiliated with, endorsed by, or connected to Land Rover, Jaguar Land Rover (JLR), or any of their subsidiaries. All vehicle names, model codes, and trademarks referenced are used for fitment identification purposes only and remain the property of their respective owners. Product photography may vary slightly from final supplied item due to the natural variation inherent in forged carbon fibre manufacturing.

نسختنا 2! - جراب إضاءة السقف من ألياف الكربون لسيارة ديفندر 2020 الجديدة. هذا التجميع سيميز المدافع الخاص بك عن الباقي. جراب سقف من ألياف الكربون مصنوع يدويًا من ألياف الكربون فائق السطوع والانسيابية للمدافع الجديد 2020. يتميز هذا بنهج غير مدمر للتثبيت وعدم وجود أخطاء عند التثبيت. يتم تشغيله مباشرة من صندوق المصهر ويتم توصيله عبر جهاز التحكم عن بعد اللاسلكي - مما يجعل مفاتيح وأجهزة القياس تبدو أصلية. مصنوعة من ألياف الكربون الحقيقية. مصابيح LED فائقة السطوع وذات مواصفات عالية. يناسب المدافع 90 و المدافع 110 تثبيت: تركيب جراب السقف الفعلي سهل للغاية. تأكد من أن السطح نظيف وقم بتركيبه باستخدام شريط 3M للسيارات. مطلوب خبرة DIY للقيام بأسلاك الأضواء. ملحوظة: هذا المنتج مصنوع من ألياف الكربون الحقيقية ومصنوع يدويًا. يمكن أن تكون العيوب الصغيرة مرئية. ملحوظة: التركيب على مسئولية العميل. طَرد 1. كل عنصر لديه تعبئة مستقلة 2. داخل كيس البولي ايثيلين، خارج علبة كرتون، التعبئة والتغليف ذات نوعية جيدة تجعل البضائع أكثر أمانا

يوفر حامل السقف لسيارة Defender L663 2020 نوعين مختلفين: الإصدارين 90 و110. بالإضافة إلى ذلك، يمكن لعملائنا الاختيار من بين خيارين للألوان – الفضي والأسود. *يتطلب رف السقف هذا قضبان سقف OE للتركيب *

Victorious Automotive · Defender L663 · Exterior Protection Gloss Black Front Bumper Guard — Land Rover Defender L663 (2020+) A precision-engineered ABS front bumper guard that fortifies your Defender L663's nose with aggressive gloss black styling — purpose-built for owners who don't compromise between looks and capability. Defender L663 2020–2026 Gloss Black ABS Construction 90 · 110 · 130 Direct Fit Off-Road Ready No Cutting Required Overview The Land Rover Defender L663 is one of the most capable and visually commanding 4x4s ever produced — a vehicle that demands accessories as serious as it is. Whether you're navigating the British countryside, tackling serious trails, or simply parked on the street, the front end of your Defender makes a statement before you've even stepped out of the door. This Gloss Black Front Bumper Guard has been designed exclusively for the Defender L663 platform, covering all body configurations — the 90, 110, and 130. Moulded from high-grade impact-resistant ABS, the guard sits flush against the factory bumper architecture, adding a layer of structural protection against stone strikes, brush, trail debris, and low-speed impacts — without adding bulk or requiring permanent modifications to your vehicle. The deep gloss black finish integrates seamlessly with the Defender's bold aesthetic, enhancing its presence while delivering the kind of functional protection that Defender owners actually rely on. Every mounting point is pre-engineered for a clean, confident fit — no guesswork, no adaptation required. What's Included 🛡️ Front Bumper Guard Gloss black ABS, pre-formed for L663 fitment 🔩 Mounting Hardware Kit All fixings and fasteners included 📐 Alignment Brackets Ensures flush, factory-quality positioning 📄 Installation Guide Step-by-step instructions for a clean fit Product Highlights Impact-resistant ABS construction — absorbs trail debris and low-speed strikes with ease Deep gloss black finish — UV-stable and resistant to surface fading over time Engineered for 90, 110 and 130 body configurations — one guard, all variants Direct OEM mounting points — no drilling, cutting or permanent modification required Lightweight by design — adds protection without meaningful weight penalty Preserves factory fog light and sensor apertures — no functional compromise Complementary to the Defender L663's angular, purposeful exterior language Compatible with capstan/winch frame systems when paired with the Enhanced Capstan Kit Designed to endure off-road environments — trail-tested geometry and fitment Clean finish from every angle — no raw edges, exposed fixings or visible seams Compatibility Model Variant Year Range Fit Defender 90 L663 — All trim levels 2020–2026 Direct Fit Defender 110 L663 — All trim levels 2020–2026 Direct Fit Defender 130 L663 — All trim levels 2020–2026 Direct Fit Defender 110 L316 (Pre-2020) Pre-2020 Not Compatible Discovery 5 L462 All Years Not Compatible Range Rover Sport L461 / L494 All Years Not Compatible Installation Notes Difficulty: Beginner — Estimated Time: 45–75 Minutes Park the Defender on a level surface and ensure the engine is off and cool before beginning work. Open the bonnet and locate the existing front bumper mounting points along the lower front fascia. Dry-fit the bumper guard against the vehicle to confirm alignment with all factory apertures and mounting holes before final installation. Insert the supplied alignment brackets into position, ensuring they seat flush against the bumper surface. Secure the guard using the included hardware kit — begin with centre fixings and work outward to ensure even pressure distribution. Verify that all fog light, parking sensor, and camera apertures remain unobstructed and fully functional. Do a final visual check from the front and sides to confirm the guard sits level and flush before torquing all fixings to hand-tight. ⚠ Important Note: A winch or capstan is not included with this kit. If you intend to use this guard with a capstan or winch frame system, the Enhanced Capstan Kit must be purchased separately — both components are required to complete the winch-ready configuration. Professional installation is recommended if you are unsure about any step. Built for Defenders. Trusted by Owners. Join over 12,300 Land Rover owners who trust Victorious Automotive for premium exterior upgrades. Browse the full Defender L663 collection and find everything your vehicle deserves. Shop Defender L663 Accessories Use code 22GET20 for 20% off when you buy any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 📦 Worldwide Shipping via DHL, FedEx, UPS & TNT 🔁 30-Day Money-Back Guarantee 📞 +44 203 943 9919 Mon–Fri, 9am–7pm Victorious Automotive is an independent aftermarket accessories retailer. This product is not manufactured by, affiliated with, endorsed by, or in any way connected to Land Rover, Jaguar Land Rover (JLR), or any of their subsidiaries. All vehicle names, model codes, and trademarks referenced are the property of their respective owners and are used solely for the purpose of fitment identification.

Victorious Automotive · Defender L663 · Exterior Lighting Gloss Black Roof Pod with Dual LED Lights for Land Rover Defender L663 2020+ A purpose-built, vehicle-specific roof pod with integrated dual LED lights — engineered to elevate the Defender's commanding presence above the windscreen, on road or trail. Defender L663 2020–2024+ Dual LED Lights Gloss Black ABS Roof Pod OEM Fitment Weather Resistant 90 · 110 · 130 Overview The Land Rover Defender L663 is a vehicle built with purpose — every line, proportion, and design detail communicates capability and intent. Owners who know their Defender understand that the right accessory doesn't fight the design, it amplifies it. That's the philosophy behind everything we build at Victorious Automotive, and this gloss black roof pod is no exception. Sculpted specifically for the L663 roofline and positioned above the windscreen, this roof pod integrates two high-output LED lights into a unified, aerodynamically considered housing. The gloss black ABS finish is UV-stabilised and weather-resistant, making it a natural companion to Defender black pack builds, Carpathian Grey stealth specs, or any dark-trimmed exterior configuration. It doesn't look fitted — it looks factory. Beyond aesthetics, the dual LED units deliver genuine output for low-light trails, forest tracks, and country lanes where the standard headlamp spread falls short. Whether you're building a capable overland platform or simply want your Defender to make a statement in an urban environment, this roof pod delivers both substance and style in a single, clean installation. What's Included 🖤 Gloss Black Roof Pod 1 x UV-stable ABS housing, vehicle-specific profile 🔦 Dual LED Light Units 2 x high-output integrated LED lights, pre-mounted 🔌 Wiring Harness Full loom for clean routing and switch integration 🔩 Mounting Hardware Basic fittings included for standard installation Product Highlights Dual high-output LED lights integrated directly into the pod housing — no external brackets Gloss black ABS construction is UV-stabilised and rated for all-weather exposure Vehicle-specific design follows the exact roofline curvature of the L663 Defender OEM-style fitment with no universal adapter plates or improvised mounting solutions Positioned above the windscreen for maximum forward light projection and visual impact Wiring harness included for clean, routed integration into DRLs, fogs, or a dedicated switch Compatible with all L663 body variants — 90, 110, and 130 configurations Suits all trim levels from entry S to V8, including X-Dynamic and black pack builds Adds purposeful, expedition-ready aesthetic without aftermarket clutter Enhances visibility on unlit trails, forest roads, and low-light off-road conditions Compatibility Model Variant Year Range Fitment Defender 90 S, SE, X-Dynamic, X, V8 2020–2024+ Direct Fit Defender 110 S, SE, X-Dynamic, X, V8 2020–2024+ Direct Fit Defender 130 S, SE, X-Dynamic, X 2022–2024+ Direct Fit Defender 110 with Factory Roof Rack All trims with OEM roof accessories occupying same mounting zone 2020–2024+ Check Clearance Classic Defender (L316) All variants Pre-2020 Not Compatible Installation Notes Difficulty: Moderate  ·  Estimated Time: 2–3 Hours  ·  Professional Install Recommended Clean and inspect the roof area above the windscreen to ensure it is clear of any factory accessories or obstructions before proceeding. Dry-fit the roof pod against the roofline to confirm alignment and identify your preferred mounting position prior to any drilling. Mark and carefully drill mounting points as required — use appropriate sealant around all penetrations to maintain weatherproofing integrity. Secure the pod housing to the roof using the supplied hardware, ensuring all fixing points are torqued correctly and flush against the panel. Route the wiring harness through the roof or A-pillar as preferred, keeping the loom away from heat sources and sharp edges throughout. Connect the LED lights to your chosen power source — a dedicated switch, DRL circuit, or auxiliary fog input are all common configurations. Test both LED units for correct operation before finalising all fittings and applying finishing trim or sealant as required. ⚠ Note: Drilling into the roof panel is required for most installations and may affect your vehicle's factory warranty on structural components. Professional installation is strongly recommended to ensure correct waterproof sealing and safe electrical integration. Always verify local road regulations regarding auxiliary lighting prior to use on public roads. Style That Shines. Power That Performs. The Defender was designed to go further than most would dare — this roof pod ensures it does so with the visibility and presence that platform commands. Explore the full Defender L663 exterior collection at Victorious Automotive and build your Defender exactly as it deserves. Shop Defender L663 Accessories Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 📦 Worldwide Shipping via DHL, FedEx, UPS & TNT 🔄 30-Day Money-Back Guarantee 📞 +44 203 943 9919 Mon–Fri, 9am–7pm Victorious Automotive is an independent aftermarket accessory retailer. We are not affiliated with, endorsed by, or in any way connected to Land Rover, Jaguar Land Rover (JLR), or any of their subsidiaries. All vehicle names, model codes, and trademarks referenced are the property of their respective owners and are used for fitment identification purposes only. Always consult a qualified technician before modifying your vehicle.

Victorious Automotive · Defender L663 · Front Bumper & Winch Land Rover Defender L663 Front Bumper & Winch Kit — Model Years 2020–2023 A precision-engineered front bumper and capstan winch kit built specifically for the Defender L663, delivering serious off-road resilience without compromising the vehicle's distinctive character. Defender L663 2020–2023 ABS Construction Defender 90 & 110 Winch Compatible Direct Fit Off-Road Exterior Upgrade Overview The Land Rover Defender L663 was engineered from the ground up to reclaim the Defender's legacy as an uncompromising off-road machine — and the 2020–2023 generation delivers exactly that. Whether you're running the compact 90 or the long-wheelbase 110, this generation of Defender demands accessories that match its capability and respect its design language. This Front Bumper and Winch Kit is developed exclusively for the L663 platform, offering a choice between a standard front bumper replacement for enhanced protection and aesthetic refinement, or the Enhanced Capstan Kit — a winch-ready configuration that transforms your Defender's front end into a recovery-capable command station. Both variants are crafted from impact-resistant ABS material, chosen for its combination of structural rigidity and low weight. The fitment is precise, the finish is consistent with Defender's rugged aesthetic, and the installation process is designed to be completed without specialist tools. For owners who take their Defender onto demanding terrain — or simply want front-end protection that reflects the vehicle's true character — this kit is the logical next step. What's Included 🛡️ Standard Front Bumper ABS construction — fits Defender 90 & 110 ⚙️ Enhanced Capstan Kit Winch-frame reinforcement for recovery use 🔩 Mounting Hardware All necessary fasteners and brackets included 📋 Installation Guide Step-by-step fitting instructions Product Highlights Engineered exclusively for the Defender L663 platform (2020–2023) Two configurations: Standard Bumper or Enhanced Capstan Winch Kit High-impact ABS construction — tough, lightweight, weather-resistant Winch-compatible capstan frame design for recovery situations Fits both Defender 90 and Defender 110 body configurations Direct OEM-style fitment — no cutting or drilling required Maintains factory sensor and camera compatibility Preserves the Defender's rugged, purposeful aesthetic Suitable for both on-road daily use and demanding off-road environments Both variants must be purchased together to use with capstan/winch frame system Compatibility Model Code Years Body Style Fitment Defender 90 L663 2020–2023 3-Door Short Wheelbase Direct Fit Defender 110 L663 2020–2023 5-Door Standard Wheelbase Direct Fit Defender 130 L663 2022–2023 5-Door Extended Wheelbase Verify Before Purchase Defender L316 L316 Pre-2016 Classic Defender Not Compatible Range Rover Sport L461 / L494 Any — Not Compatible Range Rover Vogue L460 / L405 Any — Not Compatible Installation Notes Difficulty: Moderate  ·  Estimated Time: 60–90 Minutes  ·  Tools: Basic Hand Tools Park the Defender on a flat, level surface and ensure the engine is switched off and cool before beginning work. Carefully remove the existing factory front bumper by releasing the retaining clips and unfastening the mounting bolts at each bumper end and along the lower fascia. Disconnect any parking sensor harnesses or camera connectors attached to the factory bumper — label each connector to ensure correct reassembly. If fitting the Enhanced Capstan Kit, position the winch reinforcement frame behind the new bumper aperture and secure using the supplied hardware before fitting the outer bumper skin. Align the new front bumper to the factory mounting points, ensuring the panel gaps are even on both sides before tightening any fasteners. Reconnect all sensor and camera harnesses, then test all parking sensors and any front-facing cameras via the Defender's infotainment system before completing fitment. Torque all bolts to specification per the installation guide, then carry out a final visual inspection before driving. ⚠ Important: The winch/capstan unit itself is not included with this kit. To use the capstan frame system, both the Standard Front Bumper and the Enhanced Capstan Kit variants must be purchased. If you are unsure of your specific model year or build, please contact our team on +44 203 943 9919 before ordering. Upgrade Your Defender's Front End Join over 12,300 Land Rover owners who trust Victorious Automotive for premium accessories. Browse the full Defender L663 collection and take 20% off when you purchase any two items. Shop Defender L663 Collection → Use code: 22GET20 — 20% off any 2 items ⭐ 4.9/5 Stars — 12,300+ Verified Reviews 🔄 30-Day Money-Back Guarantee 🌍 Worldwide Shipping via DHL, FedEx, UPS & TNT 📞 Mon–Fri 9am–7pm +44 203 943 9919 Victorious Automotive is an independent retailer and is not affiliated with, endorsed by, or connected to Land Rover, Jaguar Land Rover (JLR), or any of their subsidiaries. All vehicle names, model codes, and trademarks referenced — including Defender, Land Rover, and L663 — are the property of their respective owners and are used solely for fitment identification purposes.

Victorious Automotive · Defender L663 · Exterior Styling Premium Gloss Black Front Lip Splitter – Land Rover Defender 110 L663 (2020+) A precision-moulded, gloss black front lip splitter engineered to sharpen the Defender 110's stance and amplify its road presence — with zero cutting and zero compromise. Defender L663 2020–2026 Gloss Black ABS Construction OEM Fitment No Cutting Required UV Resistant Bolt-On / Bond-On Overview The Land Rover Defender 110 L663 is one of the most visually commanding vehicles on the road — purposeful, upright, and unmistakably bold. But for owners who want to push that presence further, the factory front bumper leaves room to sharpen the lower profile and bring a more performance-orientated edge to the vehicle's front end. This is exactly what the Victorious Premium Gloss Black Front Lip Splitter is built for. Engineered specifically for the Defender 110 L663 platform, this front lip is precision-moulded in high-grade ABS to follow the exact contour lines of the OEM front bumper. The result is a factory-finished look that appears as though it left the production line that way — seamlessly integrated, visually cohesive, and impeccably fitted. The deep gloss black finish adds a refined, aggressive character that works particularly well alongside dark trim packs, blacked-out wheels, and tinted details. Whether your Defender is a daily driver, a weekend escape vehicle, or a show-standard build, this front lip delivers the kind of understated enhancement that separates a well-considered build from a standard example. It's the detail that owners notice — and the detail that others can't quite put their finger on, but know makes the vehicle look significantly sharper. What's Included 🖤 Front Lip Splitter 1 x Premium Gloss Black ABS front lip — full-width, precision-moulded 🔩 Fitting Hardware Mounting fixings or adhesive tape depending on configuration selected 📋 Installation Guide Step-by-step fitment instructions included in the box Product Highlights Deep gloss black finish that is both UV-resistant and scratch-resistant for long-term kerb appeal Precision-moulded ABS construction that mirrors the exact profile of the OEM Defender 110 front bumper Lightweight yet rigid material — strong enough for all-weather driving without adding unnecessary mass OEM-style fitment requiring no cutting, drilling, or permanent modifications to the factory bumper Complements factory black packs, aftermarket wheel upgrades, and dark exterior trim seamlessly Weather-resistant surface treatment engineered to withstand rain, road grime, and temperature variation Ultra-reflective gloss surface that adds visual depth and dimension to the lower front end Compatible with bolt-on or bond-on installation methods to suit different owner preferences Consistent panel gap alignment with factory bumper lines for a professional, show-ready appearance Designed and quality-checked specifically for the L663 platform — not a generic universal fitment Compatibility Vehicle Model Code Year Range Trim Level Fitment Land Rover Defender 110 L663 2020–2026 S Direct Fit Land Rover Defender 110 L663 2020–2026 SE Direct Fit Land Rover Defender 110 L663 2020–2026 X-Dynamic SE Direct Fit Land Rover Defender 110 L663 2020–2026 X Direct Fit Land Rover Defender 110 L663 2020–2026 V8 / V8 Carpathian Direct Fit Land Rover Defender 110 L663 2020–2026 Adventure Pack fitted Direct Fit Land Rover Defender 90 L663 2020–2026 All Trims Direct Fit Land Rover Defender 130 L663 2022–2026 All Trims Direct Fit Installation Notes Difficulty: Beginner–Intermediate  ·  Estimated Time: 30–60 Minutes  ·  Tools: Basic Hand Tools or Adhesive Prep Kit Park the vehicle on a flat, level surface and ensure the front bumper is clean, dry, and free from wax or polish residue before beginning. Dry-fit the front lip against the bumper to confirm alignment and panel gap consistency before committing to any fixings or adhesive. For bolt-on configurations: locate the pre-existing bumper mounting points, align the lip bracket holes, and secure using the provided hardware — do not overtighten. For bond-on configurations: apply the provided adhesive tape or bonding compound to the inner lip flange, press firmly into position along the bumper's lower edge, and hold in place for the recommended cure time. Check all edges for consistent gap alignment and panel flush before the adhesive fully sets or hardware is fully torqued. Allow any adhesive to fully cure before driving — typically 24 hours at room temperature for optimal bond strength. Please Note: Professional installation is strongly recommended to ensure the best possible fitment and finish. This product is not compatible with vehicles fitted with the factory Adventure Pack or Urban Pack front lip kits. Always verify your vehicle's existing front bumper configuration before ordering. If you are unsure, contact our team on +44 203 943 9919 (Mon–Fri, 9am–7pm) before purchasing. Sharpen Your Stance. Define Your Presence. The Victorious Premium Gloss Black Front Lip Splitter is one of the cleanest, most effective exterior upgrades available for the Defender 110 L663. Precise fitment, premium finish, and a look that turns every road into a statement. Explore the full Defender 110 collection and build the Defender you've always had in mind. Shop All Defender L663 Accessories Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 📦 Worldwide Shipping via DHL, FedEx, UPS & TNT 🔄 30-Day Money-Back Guarantee 📞 +44 203 943 9919 Mon–Fri, 9am–7pm Victorious Automotive is an independent aftermarket accessories retailer. This product is not manufactured by, affiliated with, endorsed by, or approved by Land Rover, Jaguar Land Rover Limited (JLR), or any of their subsidiaries. All vehicle names, model codes, and trademarks referenced are used solely for fitment identification purposes and remain the property of their respective owners. Always verify compatibility with your specific vehicle specification before purchasing.

المواد: ألياف الكربون نوع العنصر: الديكور الداخلي نموذج الإعداد: لاند روفر ديفندر 2020-2021 التثبيت: الجزء الخلفي مزود بشريط لاصق للسيارات/مصنوع من ألياف الكربون الحقيقية. صنع يدوي. اللون: نمط ألياف الكربون

منتج جديد!! كن نوعًا مختلفًا من المدافع. كن الأفضل على الطريق وخارجه مع واقي غطاء المحرك الخارجي المزود بإضاءة LED مدمجة. الطقم يأتي في 3 قطع: 2 × قطع حماية جانبية 1x قطعة حماية متوسطة مزودة بمصباح LED وكابلات يمكن تكوين إضاءة LED في 4 أوضاع مختلفة. - تأثير المؤشر، يظهر تدفق الإشارة اليسرى أو اليمنى - بدء / فتح تأثير - المخاطر/ تأثير فاش مزدوج.

وصف ►يناسب طراز السيارة: يناسب Defender L663 110 2020 2021 ◀الخامة: سبيكة ألومنيوم عالية الجودة، بلاستيك، فولاذ ◀اللون: نفس الصورة الموضحة ◀العبوة: جديدة 100% في الصندوق ◀ يوصى بشدة بالتركيب الاحترافي التنسيب على السيارة: اليسار واليمين نوع المادة: ألومنيوم المواد: الألومنيوم اللون الفضي بما في ذلك: دواسة + أقواس + الأجهزة

Victorious Automotive · Defender L663 · Exterior Styling Red Brake Caliper Covers for Land Rover Defender 90 & 110 – L663 (2020–2024) A bold, precision-fitted caliper cover set that injects aggressive red contrast into the Defender's wheel arches — no drilling, no permanent modification, no compromise. Defender L663 2020–2024 Vivid Red Finish 4-Piece Set No-Drill Fit Front & Rear Brake Dust Protection Exterior Upgrade Overview The Land Rover Defender L663 — in both the compact 90 and long-wheelbase 110 body styles — is built around a character that's equal parts utilitarian and purposeful. It's a vehicle designed to be noticed, whether navigating urban environments or tackling terrain. The wheels are one of the first things the eye is drawn to, and the caliper area is one of the few visible components that most owners leave completely untouched. These red brake caliper covers are engineered specifically for the Defender 90 and 110 (2020–2024 model years, L663 platform) and slot directly over the existing brake calipers without any drilling, cutting, or permanent modification. The vivid red powder-coated finish delivers an immediate visual upgrade — transforming what is typically a dull, grey component into a deliberate styling statement that complements darker wheel finishes and the Defender's angular bodywork. Beyond aesthetics, these covers also serve a practical function. They shield the underlying calipers from road grime, brake dust accumulation, and surface corrosion — helping maintain the condition of your braking hardware between service intervals. For Defender owners who want their vehicle to look as considered underneath the arches as it does on the exterior, this is one of the most impactful and reversible upgrades available. What's Included 🔴 2x Front Caliper Covers Red finish, sized for Defender front brake assembly 🔴 2x Rear Caliper Covers Red finish, sized for Defender rear brake assembly 🔩 Fitting Hardware All necessary clips and fasteners included 📄 Installation Guide Step-by-step fitting instructions included Product Highlights Precision-engineered to fit Defender 90 & 110 L663 brake caliper geometry Vivid red powder-coated finish resists fading, chipping, and UV degradation No drilling, cutting, or permanent modification required Full four-piece set covers all four corners of the vehicle Acts as a barrier against brake dust, road grime, and surface corrosion Lightweight construction adds negligible mass to the wheel assembly Removable and fully reversible — original calipers remain untouched Compatible with standard Defender road wheels and most aftermarket rims Immediate, high-impact visual upgrade visible through open spoke wheel designs Designed and tested for the 2020–2024 L663 platform specifically Compatibility Model Platform Year Range Body Style Fit Land Rover Defender 90 L663 2020–2024 3-Door SUV Direct Fit Land Rover Defender 110 L663 2020–2024 5-Door SUV Direct Fit Land Rover Defender 130 L663 2022–2024 8-Seat Extended Verify Before Purchase Defender 90/110 (Pre-2020) L316 Pre-2020 All Not Compatible Range Rover Sport L494 L494 2013–2022 5-Door SUV Not Compatible Range Rover Vogue L460 L460 2022–2026 5-Door SUV Not Compatible Installation Notes 🔧 Difficulty: Easy  |  ⏱ Estimated Time: 30–45 Minutes  |  🛠 Tools Required: None Ensure the vehicle is parked on a level surface with the handbrake engaged and wheels cool to the touch. Do not attempt installation immediately after driving. Clean the surface of each brake caliper thoroughly using a cloth or brush to remove brake dust, grime, and any surface debris that could prevent a flush fit. Identify the correct front and rear covers — front covers are typically larger in profile. Test-fit each cover over the caliper before securing to confirm correct positioning. Align the cover squarely over the caliper housing, ensuring all edges are seated evenly. Press firmly until the securing clips engage and the cover sits flush with no movement or rattle. Repeat the process for all four corners. Once fitted, slowly rotate each wheel by hand (if jacked) or visually inspect to confirm no cover is in contact with the wheel or rotor at any point. Take the vehicle for a short, gentle test drive at low speed. Listen for any unusual sounds from the wheel area and recheck all four covers after return. ⚠ Important: These covers are a cosmetic accessory and are not designed to replace, protect, or alter the performance of your braking system. Always ensure covers are correctly and securely fitted before driving. If in doubt, consult a qualified technician. Do not install on vehicles with modified or oversized brake caliper kits without first confirming clearance. Complete Your Defender's Look These caliper covers are one piece of a broader exterior transformation. Explore our full range of Defender L663 accessories — from exterior trim upgrades to protective styling solutions — curated specifically for 2020–2024 models. Shop All Defender L663 Accessories → Use code 22GET20 for 20% off when you buy any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 📦 Worldwide Shipping via DHL, FedEx, UPS & TNT ↩ 30-Day Money-Back Guarantee 📞 +44 203 943 9919 Mon–Fri, 9am–7pm Victorious Automotive is an independent aftermarket accessories retailer. This product is not manufactured by, endorsed by, or affiliated with Land Rover, Jaguar Land Rover Limited (JLR), or any of their subsidiaries. All vehicle model names, platform codes, and trademarks referenced are the property of their respective owners and are used solely for fitment identification purposes. Always verify compatibility with your specific vehicle before purchase.

كن مستعدًا لرحلتك البرية على متن سيارة Defender 2020 L663. يأتي صندوق الأدوات هذا مزودًا بقفل ومقبس يونيون بلمسة نهائية سوداء شديدة اللمعان - تخزين متعدد الاستخدامات للحفاظ على أدواتك آمنة ومنظمة أثناء رحلاتك.

قم بترقية مظهر سيارة Defender L663 2020 الخاصة بك باستخدام أقواس العجلات الممتدة هذه. تخلق هذه الحزمة مظهرًا جريئًا للسيارة بينما يمكن الحصول على فواصل العجلات بشكل منفصل لمزيد من العرض هنا نوع المادة: ايه بي اس نوع العنصر: أقواس العجلات وزن السلعة: 3.5 كجم ميزات خاصة: لسيارة لاند روفر 2020 الدفاع عن أقواس العجلات

امنح سيارة ديفندر 2020 الخاصة بك مظهرًا متوسطًا مع مجموعات أقواس العجلات الممتدة هذه. وهذا سيعطي المدافع 2020 موقفا واسعا. يمكنك أيضًا شراء فواصل العجلات للمدافع 2020 هنا نوع المادة: ايه بي اس نوع العنصر: واقيات الطين وزن السلعة: 3.5 كجم ميزات خاصة: لسيارة لاند روفر 2020 الدفاع عن أقواس العجلات