Victorious · Range Rover Evoque · Cooling System
Radiator Top Overflow Hose for Range Rover Evoque L538 | 2.0L 16V Direct Replacement
OE-specification coolant expansion tank hose for 2.0L petrol and diesel Evoque engines—engineered for reliable thermal management.
L538
2012–2018
Petrol & Diesel
Cooling System
Direct Fit
OEM Quality
Overview
The Range Rover Evoque L538 (2012–2018) relies on a precision cooling system to manage engine heat across both 2.0L 16V petrol and diesel powerplants. The radiator top overflow hose connects the radiator's fill point to the expansion tank—a critical junction where coolant flows in both directions as engine temperature cycles.
Over time, thermal cycling causes this rubber hose to degrade: cracks form, walls soften, and connection points weaken. A compromised overflow hose allows air into the cooling loop, leading to overheating, steam plumes, and potential engine damage. This OE-specification replacement hose restores direct-fit integrity to your Evoque's thermal system.
Engineered to Partsmost OEM standards, this upper water pipe meets Land Rover's material and pressure specifications for both fuel types. Installation takes under 15 minutes with basic hand tools. Whether you're addressing visible degradation or preventive maintenance, this hose ensures your Evoque runs cool and reliably.
What's Included
🛠
Radiator Top Overflow Hose
Single replacement unit, ready to install
📋
Installation Guide
Step-by-step fitment and routing instructions
✓
30-Day Money-Back Guarantee
Full refund if not satisfied
📞
Expert Support
+44 203 943 9919 • Mon–Fri, 9am–7pm
Product Highlights
-
OE-Spec Materials: Rubber compound rated for 120°C continuous, -20°C minimum thermal extremes
-
Dual-Fuel Compatibility: Tested on both 2.0L TDV4 diesel and TDI4 petrol engines
-
Direct Replacement: Same fitment points and hose diameter as OEM; no modification needed
-
Pressure-Rated: Engineered for 1.2–1.6 bar cooling system pressure
-
Quick Install: Clamp-secured connections; under 15 minutes with hand tools
-
Expansion Tank Fitted: Pre-molded connection to tank inlet—no adapters required
-
Anti-Kink Design: Reinforced internal walls prevent collapse under vacuum
-
UV & Oil Resistant: Engine bay–grade rubber withstands oil spray and UV exposure
-
2-Year Warranty: Full manufacturer defect coverage; hassle-free replacement
-
Globally Sourced: Partsmost supplier network ensures consistent stock and rapid dispatch
Compatibility Chart
| Model & Year |
Engine |
Fitment Status |
| Range Rover Evoque L538 (2012–2015) |
2.0L 16V TDV4 Diesel |
Direct Fit |
| Range Rover Evoque L538 (2012–2015) |
2.0L 16V TDI4 Petrol |
Direct Fit |
| Range Rover Evoque L538 (2015–2018) |
2.0L 16V TDV4 Diesel |
Direct Fit |
| Range Rover Evoque L538 (2015–2018) |
2.0L 16V TDI4 Petrol |
Direct Fit |
| Range Rover Evoque L551 (2019+) |
All engines |
Not Compatible |
| Range Rover Sport L494 (2013–2020) |
All engines |
Not Compatible |
Check Your Part Number: Confirm your hose matches OEM reference LR024251 or LR060347 before ordering. If unsure, email your VIN or contact +44 203 943 9919 and we'll verify fitment instantly.
Installation & Fitment
Difficulty Level: Easy | Time: 10–15 minutes
-
Cool the Engine: Allow your Evoque to sit for 30+ minutes after running. The cooling system operates under pressure—never open when hot.
-
Locate the Hose: The radiator top overflow hose runs from the radiator filler neck (top-front of engine bay) to the expansion tank (front-right, below headlight).
-
Release Clamps: Loosen the two spring clamps (radiator end and tank end) with a screwdriver or socket wrench.
-
Drain Coolant (Optional): If you encounter spillage, place a small drain pan beneath connection points. Most hose swaps require minimal coolant loss.
-
Remove Old Hose: Gently twist and pull the old hose free from both connections. Inspect the connection ports for debris or cracks.
-
Install New Hose: Align the pre-molded radiator connector into the filler neck opening. Push firmly—you should hear a subtle click or feel resistance.
-
Secure Tank Connection: Connect the expansion tank end and position the hose routing to avoid contact with engine belts or heat sources.
-
Tighten Clamps: Re-secure both spring clamps firmly. Over-tightening can pinch the hose; snug is sufficient.
-
Check Coolant Level: Top up the expansion tank to the MAX line using your Evoque's recommended coolant blend (usually Pentosin or Jaguar/Land Rover OEM mix).
-
Run and Verify: Start the engine and allow 5 minutes of idling. Check for leaks around both connection points. No drips? Job complete.
Coolant Type: The Range Rover Evoque L538 requires a specific pink or orange long-life coolant to prevent corrosion. Do not mix coolant types. Consult your owner's manual or contact us if unsure about the correct specification for your model year.
Restore Cooling Confidence
A degraded radiator overflow hose is a silent threat—until your Evoque overheats on the motorway. This OE-specification replacement restores direct-fit reliability for both diesel and petrol L538 models. Quick install, two-year warranty, and expert support included.
Shop Range Rover Evoque Cooling Parts
Use code 22GET20 for 20% off any 2 items. Orders ship worldwide via DHL, FedEx, or UPS—typically within 48 hours.
4.9★ • 12,300+ verified reviews
✓ 30-day money-back guarantee
✓ Worldwide shipping • Free on orders £199+
✓ +44 203 943 9919 • Expert support
Disclaimer: Victorious Automotive is not affiliated with Land Rover, Range Rover, Jaguar, or any part of Jaguar Land Rover plc. All vehicle names, logos, and specifications are used solely for compatibility identification. Product specifications, fitment information, and compatibility details are provided in good faith based on supplier data and independent testing. We recommend confirming compatibility with your specific VIN before purchase. Installation of aftermarket parts may void certain manufacturer warranties. Always consult your vehicle's owner's manual for service intervals, fluid specifications, and safety guidance. Victorious Automotive accepts no liability for improper installation, misuse, or damage resulting from product use.
