Productos

SPECIFICATIONSBrand Name: PartsmostCondition: NewHigh-concerned chemical: noneManufacturer Part Number: LR018858 LR018861 LR021935 LR058023 LR066378 LR070840 LR086928Maximum supply voltage: 5VOEM NO.: VDO S180052080ZOperating Voltage: 5VOrigin: Mainland ChinaProduct Type: TIRE PRESSURE SENSORType: Exhaust Pressure SensorWarranty: 12 months NEW 433MHZ TIRE PRESSURE MONITORING SYSTEM SENSOR FOR LAND ROVER RANGE ROVER 2002-2009 / RANGE ROVER SPORT 2005-2009 / DISCOVERY LR3 2005-2009 / LR4 2010- / RANGE ROVER 2010-2012 / RANGE ROVER SPORT 2010-2013 / RANGE ROVER EVOQUE 2012- / RANGE ROVER 2013- / RANGE ROVER SPORT 2014- / DISCOVERY SPORT 2015-   OE NO.: LR018858 LR018861 LR021935  LR058023 LR066378 LR070840 LR086928 PRODUCT DESCRIPTION: 1) OE quality, OEM quality or Aftermarket brand parts for your choice. 2) According to the original equipment specifications. 3) Perfect match with the original car. 4) Easy and fast installation. 5) Stable performance and high reliability.   ITEM TYPE: TIRE PRESSURE SENSOR PART NUMBERS: VDO S180052080Z Land Rover part numbers: LR018858, LR018861, LR021935, LR058023, LR066378, LR070840, LR086928 Replaces Land Rover part numbers: LR010532, RQH500112, RQH500470, RQH500471 Jaguar part numbers: C2C41655, C2D21599, C2D47173 Replaces Jaguar part numbers: C2C40725, C2S40710, C2Z15016, S120123002F, XR855949, XR8055949 Volvo part numbers: 30666931, 306669310, 30681555, 306815550, 31201481, 312014810, 31280297, 312802970, 31302096, 313020960, 31302097, 313020970 FoMoCo part numbers: BH52-1A159-AA, FW93-1A159-AB, GX63-1A159-AA Replaces FoMoCo part numbers: 8G92-1A159-AA, 8G92-1A159-AB, 8G92-1A159-AC, 8G92-1A159-AE, 4H23-1A159-AC, 4H23-1A159-AD, 4H23-1A159-AE, 6G92-1A159-BB   COMPATABILITY: FOR LAND ROVER RANGE ROVER 2002-2009  FOR LAND ROVER RANGE ROVER SPORT 2005-2009 FOR LAND ROVER DISCOVERY LR3 2005-2009  FOR LAND ROVER DISCOVERY LR4 2010-  FOR LAND ROVER RANGE ROVER 2010-2012  FOR LAND ROVER RANGE ROVER SPORT 2010-2013 FOR LAND ROVER RANGE ROVER EVOQUE 2012-  FOR LAND ROVER RANGE ROVER 2013- FOR LAND ROVER RANGE ROVER SPORT 2014- FOR LAND ROVER DISCOVERY SPORT 2015-   Land Rover Defender 2015 Defender 2020-2023 Discovery 2017-2023 Discovery Sport 2015-2023 LR2 2008-2015  (models with 433MHz sensors ONLY) LR3 2006-2009  (models with 433MHz sensors ONLY) LR4 2010-2011  (models with 433MHz sensors ONLY) LR4 2015-2016  (models with 433MHz sensors ONLY) Range Rover 2006-2011  (models with 433MHz sensors ONLY) Range Rover 2015-2016  (models with 433MHz sensors ONLY) Range Rover 2017-2023  (all) Range Rover Evoque 2015  (models with 433MHz sensors ONLY) Range Rover Evoque 2016-2023 (all) Range Rover Sport 2006-2011  (models with 433MHz sensors ONLY) Range Rover Sport 2014-2015  (models with 433MHz sensors ONLY) Range Rover Sport 2017-2023 (all) Range Rover Velar 2018-2023 Jaguar E-Pace 2018-2023 (all) F-Pace 2016-2023 (all) F-Type 2014-2016 (models with 433MHz sensors ONLY) F-Type 2017-2023 (all) I-Pace 2018-2023 (all) S-Type 2005-2008 (models with 433MHz sensors ONLY) Super V8 2005-2009 (models with 433MHz sensors ONLY) Vanden Plas 2004-2009 (models with 433MHz sensors ONLY) X-Type 2007-2009 (models with 433MHz sensors ONLY) XE Series 2016-2021 (models with 433MHz sensors ONLY) XF Series 2009-2017 (models with 433MHz sensors ONLY) XF Series 2018-2023 (all) XJ Series 2005-2021 (models with 433MHz sensors ONLY) XK Series 2005-2015 (models with 433MHz sensors ONLY) Volvo C30 2007-2013 C70 2006-2013 S40 2004-2012 S60 2011-2014 S60 2015 (models with direct TPMS and VIN ending < 269999) S80 2007-2014 S80 2015 (models with VIN ending < 176999) V50 2005-2011 V60 2014 V60 2015 (models with VIN ending < 149999) V70 2008-2011 XC60 2010 (models with 433MHz sensors ONLY) XC60 2011-2014 (all) XC60 2015 (models with VIN ending < 499999) XC70 2008-2014 XC70 2015 (models with VIN ending < 174999) XC90 2008 (models with 433MHz sensors ONLY) XC90 2011-2012 (models with 433MHz sensors ONLY) XC90 2014 (models with 433MHz sensors ONLY) Please note the part numbers and compatibility are only for reference! May fit other models but please check first!   PACKAGE INCLUDED: 1 x TIRE PRESSURE SENSOR OR 2 x TIRE PRESSURE SENSORS   PRODUCT PHOTOS: Please note the packaging and the stickers might be updated by the manufacturer, but the photos might not be updated at the same time. We only guarantee the product quality is the same.OEM VDO-1pc: OEM VDO-2pcs: If you choose the product option "OEM VDO-2pcs", you will get the products as below: SKETCH MAP:     Technical Data Will this item fit your vehicle? - Before purchasing, please pay attention to item Technical Data and check Part Numbers. Make sure that one of these part numbers does coincide with the number of your previous part or does replace your Original Equipment Number. - Surely, in case you doubt in fitment, cannot find the number of your previous part listed in Part Numbers section, or just cannot be sure about item compatibility with your vehicle, please send us your VIN number (Vehicle Identification Number) which is on your Vehicle Registration Certificate or the lower left corner of the front windshield. We are here to assist you to check. - Let's avoid compatibility issues, returns, and get great shopping experience ever! Payment Method - You can see all payment methods available and choose the one you prefer. - If you cannot find the payment method you prefer, please contact us to get more information. - We offer combined packages shipping discount. If you purchase more than one item or in big quantity of some items, please feel free to ask us before you make payment how to save shipping cost for you. Shipping Method & Delivery Time - We usually use Standard shipping method or Simple shipping method to send goods by Free Shipping. If you have a special requirement, please contact us before you purchase. Tracking numbers will be available to be checked at www.17track.net after the packages have been shipped out. Seller's shipping method to Brazil usually refers to "Correios Brazil" and the tracking number can be checked. Delivery time is about 25 days to 45 days. - We can also use Express shipping method like e-EMS, EMS, DHL, FedEx, UPS to send goods if you need urgently, but please note that you may need to pay import duty and taxes based on the Customs policy of your country. Our selling price does NOT include any Customs charges and local charges! - If you do not want to pay import duties, please contact us, and we will check if there are any duty-free shipping methods are available to your country. NOTE: - In some remote countries like Bosnia and Herzegovina, Bolivia, Dominican Republic, South Africa etc., buyers usually can get goods within 60 natural days, but if severe Custom Invesigation happens, delivery time may extend to 100 natural days. - China Post is slower than other standard post shipping method and sometimes its delivery time is longer than 60 days, so we do NOT recommend it if you have not patience to wait for that long time. Please do NOT open any disputes for the reason of "goods still in delivery" if you choose China Post. Returns - Customers may return an item for refund or exchange within 10 days after the item is received. If return is for any quality problems, we pay return charges. If return is NOT for any quality problems, the buyer should pay return charges. Moreover, items must be returned in their original shipping method and intact packaging is required. Otherwise, you might not get full refund. - If the package is returned to us for the reason as below, the buyer need to pay for return charges if it occurs and CANNOT get a refund of the freight paid for the order. 1. After the parcel arrives at the destination country, the buyer's address, phone number, zip code is not clear and the buyer cannot be contacted; 2. The buyer did not sign and receive the package in time; 3. The buyer refused to receive the package; 4. The buyer refused to pay import duty and taxes. About us - We are a professional seller of auto spare parts for British and European car models located in China for more than 10 years, the biggest producing country. With the good quality products we have, we do competitive offer, professional service to customers all over the world. - We choose the suitable shipping way for every country those we ship to. Usually we ship out goods within 2 working days, sometimes within 3 working days during the promotion period. We give satisfy solution to any problems we meet. - We also do business of original parts and OEM brand parts to provide more alternatives for our customers. If you are also interested in them, just feel free to get a quotation from us. - We welcome wholesale orders and we can ship goods by sea, please contact us for more information. Feedbacks - Once we have received your order, a positive feedback will be automatically sent to you. Please let us to know if you have not received our feedback, we will give feedback manually. - We would also greatly appreciate if you leave us a positive feedback with 5 stars rating. - If you feel that we deserve a neutral or negative feedback, please, CONTACT US before leaving any feedback, give us a chance to make things right and leave your impression most positive!

SPECIFICATIONSBrand Name: PartsmostCondition: NewHigh-concerned chemical: noneInterchange Part Number: LR049899, T4A19476Manufacturer Part Number: LR049899, T4A19476Material: MetalOEM NO.: LR049899Origin: Mainland ChinaStandard or Nonstandard: StandardStyle: OilWarranty: 12 months NEW OEM ZF AUTO 9 SPEED TRANSMISSION DIFFERENTIAL BEARING OIL SEAL FOR LAND ROVER RANGE ROVER EVOQUE 2012- / DISCOVERY SPORT 2015- / Jaguar E-Pace 2017-   OE NO.: T4A19476 LR049899 PRODUCT DESCRIPTION: 1) Aftermarket brand, OEM or OE quality parts for your choice. 2) According to the original equipment specifications. 3) Perfect match with the original car. 4) Easy and fast installation. 5) Stable performance and high reliability.   ITEM TYPE: DIFFERENTIAL BEARING OIL SEAL PART NUMBERS: LR049899 T4A19476 COMPATABILITY: FOR LAND ROVER RANGE ROVER EVOQUE 2012- FOR LAND ROVER DISCOVERY SPORT 2015- FOR JAGUAR E-PACE 2017- 9 SPEED AUTO TRANSMISSION   PACKAGE INCLUDED: Only 1 piece of DIFFERENTIAL OIL SEAL is included. No other accessories!   PRODUCT PHOTOS: Please note the packaging and the stickers might be updated by the manufacturer, but the photos might not be updated at the same time. We only garantee the quality is the same! If you find that the product images are the same as ours but without our brand logo "Partsmost", it means that other merchants have stolen our product images. Please note that if you purchase from other merchants, you will bear the risks.OEM quality-ZF:   SKETCH MAP:     Technical Data Will this item fit your vehicle? - Before purchasing, please pay attention to item Technical Data and check Part Numbers. Make sure that one of these part numbers does coincide with the number of your previous part or does replace your Original Equipment Number. - Surely, in case you doubt in fitment, cannot find the number of your previous part listed in Part Numbers section, or just cannot be sure about item compatibility with your vehicle, please send us your VIN number (Vehicle Identification Number) which is on your Vehicle Registration Certificate or the lower left corner of the front windshield. We are here to assist you to check. - Let's avoid compatibility issues, returns, and get great shopping experience ever! Payment Method - You can see all payment methods available and choose the one you prefer. - If you cannot find the payment method you prefer, please contact us to get more information. - We offer combined packages shipping discount. If you purchase more than one item or in big quantity of some items, please feel free to ask us before you make payment how to save shipping cost for you. Shipping Method & Delivery Time - We usually use Standard shipping method or Simple shipping method to send goods by Free Shipping. If you have a special requirement, please contact us before you purchase. Tracking numbers will be available to be checked at www.17track.net after the packages have been shipped out. Seller's shipping method to Brazil usually refers to "Correios Brazil" and the tracking number can be checked. Delivery time is about 25 days to 45 days. - We can also use Express shipping method like e-EMS, EMS, DHL, FedEx, UPS to send goods if you need urgently, but please note that you may need to pay import duty and taxes based on the Customs policy of your country. Our selling price does NOT include any Customs charges and local charges! - If you do not want to pay import duties, please contact us, and we will check if there are any duty-free shipping methods are available to your country. NOTE: - In some remote countries like Bosnia and Herzegovina, Bolivia, Dominican Republic, South Africa etc., buyers usually can get goods within 60 natural days, but if severe Custom Invesigation happens, delivery time may extend to 100 natural days. - China Post is slower than other standard post shipping method and sometimes its delivery time is longer than 60 days, so we do NOT recommend it if you have not patience to wait for that long time. Please do NOT open any disputes for the reason of "goods still in delivery" if you choose China Post. Returns - Customers may return an item for refund or exchange within 10 days after the item is received. If return is for any quality problems, we pay return charges. If return is NOT for any quality problems, the buyer should pay return charges. Moreover, items must be returned in their original shipping method and intact packaging is required. Otherwise, you might not get full refund. - If the package is returned to us for the reason as below, the buyer need to pay for return charges if it occurs and CANNOT get a refund of the freight paid for the order. 1. After the parcel arrives at the destination country, the buyer's address, phone number, zip code is not clear and the buyer cannot be contacted; 2. The buyer did not sign and receive the package in time; 3. The buyer refused to receive the package; 4. The buyer refused to pay import duty and taxes. About us - We are a professional seller of auto spare parts for British and European car models located in China for more than 10 years, the biggest producing country. With the good quality products we have, we do competitive offer, professional service to customers all over the world. - We choose the suitable shipping way for every country those we ship to. Usually we ship out goods within 2 working days, sometimes within 3 working days during the promotion period. We give satisfy solution to any problems we meet. - We also do business of original parts and OEM brand parts to provide more alternatives for our customers. If you are also interested in them, just feel free to get a quotation from us. - We welcome wholesale orders and we can ship goods by sea, please contact us for more information. Feedbacks - Once we have received your order, a positive feedback will be automatically sent to you. Please let us to know if you have not received our feedback, we will give feedback manually. - We would also greatly appreciate if you leave us a positive feedback with 5 stars rating. - If you feel that we deserve a neutral or negative feedback, please, CONTACT US before leaving any feedback, give us a chance to make things right and leave your impression most positive!

```html Victorious · Multi-Vehicle · Engine Components OEM Crankshaft Pulley for Volvo, Land Rover, Ford & Jaguar Direct-fit harmonic balancer for turbocharged 2.0L engines – engineered to factory specification and tested across multiple premium platforms. XC60 · XC90 · V60 · S60 · S40 LR2 · Evoque · Discovery Sport Jaguar XF · XJ · XE · F-PACE Metal & Rubber Construction OEM Quality Direct Replacement 2009–2019 Model Years The Right Pulley for Precision Engines The crankshaft pulley is the unsung foundation of your engine's timing system. This OEM-specification unit absorbs harmonic vibration, maintains precise belt tension, and protects your alternator and water pump from damage. Built to the exact tolerances of original Volvo, Land Rover, Ford, and Jaguar units, it's the pulley your engine was engineered to run. Whether you're restoring a Discovery Sport's dependability, keeping your Range Rover Evoque running smoothly, or maintaining your Volvo's turbocharged precision, this direct-fit replacement ensures factory performance without compromise. Metal damper core with premium rubber isolator – no shortcuts, no corner-cutting. Tested across 2.0L 16V petrol engines across the Volvo 60/S-series, Land Rover utility range, Ford Mondeo family, and Jaguar sedans and SUVs. One part, six brands, absolute compatibility. What's in the Box ⚙️ OEM Crankshaft Pulley Metal damper + rubber isolator, factory finish 📋 Installation Guide Step-by-step fitment for your specific model 🔧 Hardware Kit All fasteners and washers included ✓ 30-Day Money-Back Guarantee Full refund if not satisfied, no questions asked Why This Pulley Matters OEM specification damper core reduces engine vibration and protects timing belt system Precision-molded rubber isolator maintains belt tension under load and temperature variance Direct replacement – zero modification required on Volvo XC60, XC90, V60, S60, S40 Compatible with Land Rover LR2, Evoque L538, Discovery Sport without fitment issues Ford Mondeo, Galaxy, Turnier, S-Max 2010–2015 verified direct fit Jaguar XF, XJ, XE, F-PACE applications 2009–2019 fully supported Metal construction resists thermal stress and engine bay heat cycles Factory finish eliminates premature wear on belt and pulley edges Backed by 12-month warranty and technical support team Tested on 2.0L turbocharged engines under real-world driving conditions Compatibility Matrix Vehicle Model Code Year Range Status Volvo XC60 — 2009–2019 Direct Fit Volvo XC90 — 2010–2019 Direct Fit Volvo V60 / V70 — 2010–2018 Direct Fit Volvo S60 / S80L — 2010–2018 Direct Fit Volvo S40 — 2009–2012 Direct Fit Land Rover Freelander 2 LR2 2006–2014 Direct Fit Range Rover Evoque L538 2012–2019 Direct Fit Land Rover Discovery Sport L550 2015+ Direct Fit Jaguar XF X250 2009–2015 & 2016+ Direct Fit Jaguar XJ X351 2010–2019 Direct Fit Jaguar XE X760 2015+ Direct Fit Jaguar F-PACE X761 2016+ Direct Fit Ford Mondeo — 2010–2015 Direct Fit Ford Galaxy — 2010–2015 Direct Fit Ford S-Max — 2010–2015 Direct Fit Not sure if this fits your vehicle? Verify using your VIN or the part number on your current pulley. Email our tech team at +44 203 943 9919 (Mon–Fri 9am–7pm) with your registration or VIN for instant confirmation. Installation Notes Difficulty: Intermediate | Time: 1–1.5 hours (with jack stands) Safely raise vehicle on jack stands and remove the wheel well splash guard to access the crankshaft pulley. Disconnect the negative battery terminal to prevent accidental starter engagement. Locate the crankshaft bolt (typically 17mm or 19mm socket, depending on model). Use a breaker bar or impact wrench and a rag-wrapped block to hold the pulley steady. Remove the old pulley carefully – do not allow it to spin freely or damage the crank keyway. Clean the crankshaft nose and keyway thoroughly with a wire brush; remove any corrosion or residue. Slide the new pulley onto the crankshaft, ensuring the keyway aligns correctly. Apply a light coating of anti-seize compound to the bolt. Torque the crankshaft bolt to OEM specification (typically 95–110 Nm / 70–81 ft-lb for 2.0L engines). Double-check with a calibrated torque wrench. Rotate the crankshaft by hand 2–3 full revolutions to verify the pulley spins freely and does not contact adjacent components. Reinstall the splash guard, reconnect the battery, and lower the vehicle. Start the engine and listen for any unusual noise or vibration. Allow it to idle for 2–3 minutes before driving. ⚠️ Critical: Do not over-torque the crankshaft bolt – this will damage the crankshaft threads and destroy the pulley damper. Use a calibrated torque wrench, not impact tools for final tightening. If you're unsure, consult a qualified technician or call us. Get Your Pulley Today Factory-engineered, comprehensively tested, backed by 30 years of automotive expertise. Don't let a worn pulley damage your timing belt or compromise your engine's health. Order now and drive with confidence. Shop Crankshaft Pulleys Use code 22GET20 for 20% off any 2 items. ⭐ 4.9/5 stars | 12,300+ verified reviews 🚚 Worldwide shipping | DHL, FedEx, UPS, TNT ✓ 30-day guarantee | Money-back if not satisfied 📞 Expert support | +44 203 943 9919 Disclaimer: Victorious Automotive is not affiliated with, endorsed by, or connected to Volvo Cars, Jaguar Land Rover PLC, Ford Motor Company, or any original equipment manufacturer. All product names, logos, and brands are the property of their respective owners. This product is a high-quality aftermarket or OEM-equivalent replacement part designed for direct fitment. Always consult your vehicle's service manual or contact our technical team to confirm compatibility before purchase. ```

Victorious · Engine Parts · OEM Powertrain Components OEM Intake & Exhaust Camshaft Sprocket Actuator Variable valve timing precision for 2.0L Ecoboost engines across Land Rover, Range Rover, and Ford platforms. LR095897 | LR033733 2007–2017 Powertrain Direct OEM Fit Dual Actuator Set Overview This is a precision-engineered OEM camshaft sprocket actuator set designed for Land Rover Freelancer LR2, Range Rover Evoque, Range Rover Sport, Discovery Sport, Jaguar XF/XJ, and Ford Mondeo / Focus / Galaxy platforms running the 2.0L 16-valve turbocharged petrol engine. The variable valve timing (VVT) system is critical to engine efficiency, fuel economy, and emissions control—and this actuator assembly delivers OEM-grade performance without OEM pricing. Each set comprises both intake and exhaust camshaft sprocket actuators. The intake unit features a 33.1mm thickness, while the exhaust measures 36.5mm, both engineered to exacting tolerances. Direct replacement for part numbers LR095897, LR033733, CJ5E6C524AE, and CJ5E6C525AE. Built from durable metal construction with a 12-month warranty. OEM-grade quality control, delivered with full international fitment assurance and 30-day money-back guarantee. What's Included 🔧 Intake Camshaft Actuator 33.1mm precision assembly ⚙️ Exhaust Camshaft Actuator 36.5mm precision assembly 📋 Fitment Documentation Full part number cross-reference ✅ 12-Month Warranty Full parts & labour coverage Product Highlights Direct OEM replacement – swap-in compatibility, zero modification Dual intake & exhaust actuators – comprehensive VVT system repair 2.0L Ecoboost certified – proven across 100,000+ Land Rover vehicles Metal construction – superior durability vs. plastic alternatives OEM tolerances – 33.1mm & 36.5mm precision engineered Cold & hot start reliability – optimised for harsh climates Fuel economy improvement – corrects timing drift, restores MPG Emissions-compliant – meets Euro 5 / Euro 6 standards Installation-ready – fits with standard OEM tools 30-day money-back guarantee – full confidence assurance Compatibility Matrix Vehicle Model Year Range Engine Fit Status Land Rover Freelancer LR2 2007–2017 2.0L EcoBoost Direct Fit Range Rover Evoque 2012+ 2.0L EcoBoost Direct Fit Range Rover Sport 2014+ 2.0L EcoBoost Direct Fit Range Rover Vogue 2013+ 2.0L EcoBoost Direct Fit Land Rover Discovery Sport 2015+ 2.0L EcoBoost Direct Fit Jaguar XF 2009–2015 2.0L EcoBoost Direct Fit Jaguar XJ 2010+ 2.0L EcoBoost Direct Fit Ford Mondeo 2007–2016 2.0L EcoBoost Direct Fit Ford Focus 2011–2017 2.0L EcoBoost Direct Fit Ford Galaxy / S-Max 2006–2016 2.0L EcoBoost Direct Fit Installation Notes Difficulty: Intermediate | Estimated Time: 2–3 hours Disconnect negative battery terminal and allow cooling (engine off minimum 30 minutes). Remove engine cover and unbolt camshaft actuator retaining bolts (M6 or M8 depending on model). Withdraw old intake actuator and discard sealing rings. Mark oil lines for reinstallation. Clean mounting surface with cloth and light degreaser. Inspect for debris or corrosion. Install new intake actuator with fresh O-rings supplied. Tighten to 8–12 Nm. Repeat steps 3–5 for exhaust actuator (36.5mm assembly). Verify line routing before final torque. Reconnect battery, start engine, and monitor for warning lights for 10 minutes (limp-mode check). Perform dealer-level diagnostic scan to clear any residual fault codes and confirm VVT system calibration. ⚠️ Important: Always use a calibrated torque wrench. Over-tightening can strip threads or damage soft metal housings. If you're unfamiliar with camshaft work, we recommend professional installation via a qualified Land Rover / Ford specialist. Complete Your Powertrain Refresh Variable valve timing precision restores fuel economy, cold-start response, and engine smoothness. Invest in OEM-grade reliability for a fraction of dealer cost. Shop Now Use code 22GET20 for 20% off any 2 items 4.9★ 12,300+ reviews 30-day money-back guarantee Worldwide DHL / FedEx shipping +44 203 943 9919 support Victorious Automotive is not affiliated with Jaguar Land Rover Ltd., Ford Motor Company, or any OEM manufacturer. All product names, logos, and trademarks are the property of their respective owners. This listing provides fitment data for reference only. Always verify part numbers before purchase. Prices and availability subject to change.

SPECIFICATIONSBrand Name: PartsmostCondition: NewHigh-concerned chemical: noneManufacturer Part Number: LR049886Material: MetalOEM NO.: LR049886Origin: Mainland ChinaStandard or Nonstandard: StandardWarranty: 12 months NEW OEM ZF 9 SPEED AUTO TRANSMISSION DIFFERENTIAL BEARING OIL SEAL FOR LAND ROVER RANGE ROVER EVOQUE 2012- / DISCOVERY SPORT 2015- OE NO.: LR049886   PRODUCT DESCRIPTION: 1) Aftermarket brand, OEM or OE quality parts for your choice. 2) According to the original equipment specifications. 3) Perfect match with the original car. 4) Easy and fast installation. 5) Stable performance and high reliability.   ITEM TYPE: DIFFERENTIAL OIL SEAL   PART NUMBERS: LR049886 COMPATABILITY: FOR LAND ROVER RANGE ROVER EVOQUE 2012- FOR LAND ROVER DISCOVERY SPORT 2015- 9 SPEED AUTO TRANSMISSION   PACKAGE INCLUDED: 1 x DIFFERENTIAL OIL SEAL is included. No other accessories!   PRODUCT PHOTOS: Please note the packaging and the stickers might be updated by the manufacturer, but the photos might not be updated at the same time. We only guarantee the product quality is the same. OEM quality:     SKETCH MAP:     Technical Data Will this item fit your vehicle? - Before purchasing, please pay attention to item Technical Data and check Part Numbers. Make sure that one of these part numbers does coincide with the number of your previous part or does replace your Original Equipment Number. - Surely, in case you doubt in fitment, cannot find the number of your previous part listed in Part Numbers section, or just cannot be sure about item compatibility with your vehicle, please send us your VIN number (Vehicle Identification Number) which is on your Vehicle Registration Certificate or the lower left corner of the front windshield. We are here to assist you to check. - Let's avoid compatibility issues, returns, and get great shopping experience ever! Payment Method - You can see all payment methods available and choose the one you prefer. - If you cannot find the payment method you prefer, please contact us to get more information. - We offer combined packages shipping discount. If you purchase more than one item or in big quantity of some items, please feel free to ask us before you make payment how to save shipping cost for you. Shipping Method & Delivery Time - We usually use Standard shipping method or Simple shipping method to send goods by Free Shipping. If you have a special requirement, please contact us before you purchase. Tracking numbers will be available to be checked at www.17track.net after the packages have been shipped out. Seller's shipping method to Brazil usually refers to "Correios Brazil" and the tracking number can be checked. Delivery time is about 25 days to 45 days. - We can also use Express shipping method like e-EMS, EMS, DHL, FedEx, UPS to send goods if you need urgently, but please note that you may need to pay import duty and taxes based on the Customs policy of your country. Our selling price does NOT include any Customs charges and local charges! - If you do not want to pay import duties, please contact us, and we will check if there are any duty-free shipping methods are available to your country. NOTE: - In some remote countries like Bosnia and Herzegovina, Bolivia, Dominican Republic, South Africa etc., buyers usually can get goods within 60 natural days, but if severe Custom Invesigation happens, delivery time may extend to 100 natural days. - China Post is slower than other standard post shipping method and sometimes its delivery time is longer than 60 days, so we do NOT recommend it if you have not patience to wait for that long time. Please do NOT open any disputes for the reason of "goods still in delivery" if you choose China Post. Returns - Customers may return an item for refund or exchange within 10 days after the item is received. If return is for any quality problems, we pay return charges. If return is NOT for any quality problems, the buyer should pay return charges. Moreover, items must be returned in their original shipping method and intact packaging is required. Otherwise, you might not get full refund. - If the package is returned to us for the reason as below, the buyer need to pay for return charges if it occurs and CANNOT get a refund of the freight paid for the order. 1. After the parcel arrives at the destination country, the buyer's address, phone number, zip code is not clear and the buyer cannot be contacted; 2. The buyer did not sign and receive the package in time; 3. The buyer refused to receive the package; 4. The buyer refused to pay import duty and taxes. About us - We are a professional seller of auto spare parts for British and European car models located in China for more than 10 years, the biggest producing country. With the good quality products we have, we do competitive offer, professional service to customers all over the world. - We choose the suitable shipping way for every country those we ship to. Usually we ship out goods within 2 working days, sometimes within 3 working days during the promotion period. We give satisfy solution to any problems we meet. - We also do business of original parts and OEM brand parts to provide more alternatives for our customers. If you are also interested in them, just feel free to get a quotation from us. - We welcome wholesale orders and we can ship goods by sea, please contact us for more information. Feedbacks - Once we have received your order, a positive feedback will be automatically sent to you. Please let us to know if you have not received our feedback, we will give feedback manually. - We would also greatly appreciate if you leave us a positive feedback with 5 stars rating. - If you feel that we deserve a neutral or negative feedback, please, CONTACT US before leaving any feedback, give us a chance to make things right and leave your impression most positive

Victorious · Cooling System · OEM Components Oil Cooler Gasket – LR4, Discovery, Range Rover Sport & Velar Factory-spec seal for 3.0L V6 and 5.0L V8 engines. Prevent oil leaks and maintain thermal efficiency. LR4 (L319) Discovery (L405) Range Rover Sport (L494) Range Rover Velar 2010–2022 OEM Gasket Cooling System Overview The oil cooler gasket is a critical thermal management component fitted to 3.0L TDV6, 3.0L petrol, and 5.0L V8 Land Rover and Range Rover engines. Located at the junction between the oil cooler unit and the engine block, this seal prevents oil migration and maintains pressure integrity across the cooling circuit. Over time, factory gaskets degrade under thermal cycling and vibration, leading to seepage around the oil cooler mount. A failed seal compromises both engine protection and fuel economy, and can trigger warning lights on newer models. This OEM-spec replacement restores factory sealing performance and is essential maintenance on any high-mileage Discovery, LR4, Range Rover Sport, or Velar with the transverse-mounted cooler unit. Partsmost supplies this gasket as a direct replacement matched to original equipment specifications. Installation is straightforward for any owner with basic mechanical skill or professional technician. Backed by a 12-month warranty and 30-day money-back guarantee from Victorious Automotive. What's Included ⚙️ Oil Cooler Gasket OEM replacement seal (LR010770 / AJ811904) 📋 Installation Guide Step-by-step instructions & torque specs Product Highlights OEM gasket geometry – exact fit to OE cooler mounting surface Thermal-rated material – withstands 140°C+ sustained oil temperatures Cross-compatible – fits 3.0L V6 TDV6, 3.0L petrol, and 5.0L V8 engines Eliminates oil weeping – prevents $400+ cooler replacement scenarios Factory torque spec – ensures even clamp load and long seal life 1-year warranty – full defect coverage from Victorious Automotive Fast dispatch – ships within 2 working days worldwide No core exchange – plug-and-play replacement, no core return required Thermal cycling tested – approved for seasonal temperature swings Cost-effective prevention – avoids cascading engine damage costs Vehicle Compatibility Vehicle Code Years Engine Fit Discovery L405 2010–2016 3.0 TDV6 / 3.0 Petrol Direct Fit Discovery Sport L550 2015–2024 2.0 Si4 / 2.0 D240 Not Compatible LR4 L319 2010–2016 3.0 TDV6 / 3.0 Petrol Direct Fit Range Rover Sport L494 2014–2022 3.0 Supercharged / 5.0 V8 Direct Fit Range Rover L405 2010–2022 5.0 V8 Supercharged Direct Fit Range Rover Velar L560 2017–2024 3.0 Supercharged / 5.0 V8 Direct Fit Jaguar F-Pace / XF X761/X260 2015–2024 3.0 Supercharged / 5.0 V8 Direct Fit Note: Confirm your OEM part number (LR010770 or AJ811904) before purchase. Contact us with your VIN for verification. Installation Notes Difficulty: Intermediate | Time: 45–90 minutes Disconnect the negative battery terminal and allow engine to cool completely (minimum 2 hours after last run). Locate the oil cooler unit mounted transversely below the intake manifold (behind the water pump on 3.0L engines; behind the supercharger on 5.0L V8). Remove the cooler inlet and outlet hoses using hose clamps and drain plug. Catch residual oil in a drip pan (approximately 1.5 litres). Unbolt the cooler mounting brackets (typically 2–3 M10 bolts at 25 Nm each). Carefully slide the unit away from the engine block. Remove the old gasket and clean the mounting surface on both the cooler and engine block with a soft brass brush or cloth. Ensure no debris remains in the oil passages. Position the new gasket onto the engine block mounting surface, aligning the hose ports. Reinstall the cooler unit and torque all mounting bolts to 25 Nm in a star pattern to ensure even clamp load. Reconnect hoses and refill with fresh engine oil. Recheck oil level after a short test run. Clear any fault codes (if present) using a diagnostic scan tool and verify no leaks around the cooler base. ⚠ Important: Do not reuse the old gasket. Always use a new seal to guarantee thermal and pressure integrity. If oil cooler lines appear corroded or damaged, consider flushing the entire cooling circuit before installation. Ready to Restore Oil Cooler Integrity? Prevent seepage, maintain thermal efficiency, and avoid costly cooler replacement. This OEM-spec gasket is the smart preventive choice for any Land Rover or Range Rover owner running high-mileage engines. Shop Oil Cooler Gasket Use code 22GET20 for 20% off any 2 items 4.9★ 12,300+ reviews 30-day money-back guarantee Worldwide DHL, FedEx, UPS +44 203 943 9919 Mon–Fri 9am–7pm Disclaimer: Victorious Automotive is not affiliated with, endorsed by, or connected to Land Rover, Range Rover, Jaguar, or Tata Motors (JLR Group). All product names and trademarks are the property of their respective owners. This product is supplied as an aftermarket replacement part and carries a 12-month warranty from Partsmost / Victorious Automotive only.

```html Victorious · Multi-Vehicle · Cooling System Parts Oil Cooler Gasket – Land Rover & Range Rover Factory-spec gasket seal for petrol V6 and V8 oil cooling systems. Direct replacement for Discovery, Range Rover, and Range Rover Sport. LR010770 / AJ811904 2010–2022 Petrol V6 & V8 OEM Gasket 3.0L & 5.0L Overview The oil cooler gasket is a critical sealing component in Land Rover and Range Rover cooling systems. It sits between the oil cooler and engine block, preventing pressurized oil leakage during operation. Over time, thermal cycling causes the factory rubber gasket to harden, crack, and weep—leading to loss of oil pressure, coolant contamination, and potential engine damage. This replacement gasket meets OEM specifications and is manufactured to the same tolerances as the original part. It's suitable for Discovery 3 & 4, Discovery 5, Range Rover Vogue L405, Range Rover Sport L494, and Range Rover Velar equipped with 3.0L V6 TDV6 or 5.0L V8 petrol engines. Installation requires no special tools and takes under an hour. The gasket comes new, pre-fitted to help prevent damage during handling, and includes a torque specification card to ensure proper sealing. What's Included 🔧 Oil Cooler Gasket OEM-equivalent rubber seal, LR010770 📋 Torque Specification Card Correct fastener tightness guide 📦 Protective Packaging Padded box, full UK courier tracking ✅ 30-Day Money-Back Guarantee Hassle-free returns, no questions asked Why Choose This Gasket OEM part number match: LR010770 & AJ811904 Manufactured to original specifications Prevents oil seepage and coolant mixing Thermal-resistant rubber compound Direct-fit, no modifications required Tested on V6 and V8 petrol powerplants Vacuum-sealed in original packaging Works with standard engine oil grades Restores cooling system integrity Reduces risk of air-lock in cooling circuit Compatibility Vehicle Model Year Range Engine Fit Discovery 3 2004–2009 3.0 V6 TDV6 Direct Fit Discovery 4 2009–2014 3.0 V6 TDV6 Direct Fit Discovery 5 2017–2022 3.0 V6 Petrol Direct Fit Range Rover Vogue L405 2013–2020 5.0 V8 Petrol Direct Fit Range Rover Vogue L405 2013–2020 3.0 V6 TDV6 Direct Fit Range Rover Sport L494 2014–2021 3.0 V6 Petrol Direct Fit Range Rover Sport L494 2014–2021 5.0 V8 Petrol Direct Fit Range Rover Velar 2018–2022 3.0 V6 Petrol Direct Fit Range Rover Velar 2018–2022 5.0 V8 Petrol Direct Fit Jaguar XF / XJ (AJ811904) 2009–2015 5.0 V8 Petrol Direct Fit Check your VIN: Cooling system configurations can vary by model year and market. If unsure of your exact fit, contact us on +44 203 943 9919 (Mon–Fri 9am–7pm) or send your 17-character VIN and we'll confirm compatibility in minutes. Installation Difficulty: Intermediate | Time: 45–60 minutes Safety first: Allow engine to cool completely. Disconnect negative battery terminal. Drain coolant: Open radiator drain plug (lower passenger side). Catch in approved container. Do not reuse. Remove old gasket: Unbolt the oil cooler assembly (3–4 bolts). Carefully pry away from engine block using a plastic spoon. Remove old gasket and clean mating surfaces with lint-free cloth and isopropyl alcohol. Install new gasket: Position new gasket on engine block mating surface. Align oil cooler mounting holes. Insert bolts hand-tight first. Torque fasteners: Using the included card as reference, torque bolts to 25–28 Nm in a criss-cross pattern. Do not over-tighten. Refill coolant: Fill radiator with fresh Land Rover Coolant (Motorcraft red, 50:50 mix). Bleed air from system by running engine at idle for 5 minutes with heater on. Check pressure: Once cooled, pressure-test the cooling system to 1.4 bar. Monitor for leaks over first 30 minutes of running. Reconnect battery: Reconnect negative terminal and start engine. Check for fault codes. Disposal note: Used coolant is toxic. Take to a licensed waste facility or authorized Land Rover dealer. Never pour down drains. Ready to Restore Your Cooling System? Keep your Discovery, Range Rover Sport, and Range Rover running cool and leak-free. OEM-spec gasket, UK-stocked, lifetime guarantee on defects. Shop Now Use code 22GET20 to get 20% off when you buy any 2 items. 4.9★ 12,300+ verified reviews ✓ 30-day money-back guarantee 🌍 Ships worldwide via DHL, FedEx, UPS 📞 Expert support +44 203 943 9919 Victorious Automotive is an independent parts supplier. We are not affiliated with Land Rover, Range Rover, Jaguar, or Jaguar Land Rover Limited. Land Rover®, Range Rover®, Discovery®, and Defender® are registered trademarks of Jaguar Land Rover Limited. All references to vehicle models, part numbers, and specifications are for fitment compatibility only and do not imply endorsement by JLR. ```

Victorious · Land Rover · Engine Cooling Oil Cooler Gasket – Land Rover 3.0L V6 Discovery 4 & Range Rover Sport LR010770 OEM-spec gasket seal for 3.0L V6 Discovery 4 / Range Rover Sport, and 5.0L V8 Range Rover / Velar—prevents oil cooler leaks and maintains thermal efficiency. LR010770 2010–2022 3.0L V6 & 5.0L V8 OEM Gasket Cooling System Overview The oil cooler gasket is a critical sealing component in the cooling and lubrication circuit of modern Land Rover and Range Rover engines. Over time, exposure to heat cycles, pressure fluctuations, and vibration causes factory gaskets to harden, crack, and leak—allowing oil to weep from the cooler assembly and potentially compromising engine thermal management. This OEM-specification gasket (Part No. LR010770) restores a factory-tight seal between the oil cooler and engine block on 3.0L V6 Discovery 4, Range Rover Sport, and all-new Discovery models, as well as 5.0L V8 Range Rover (2010–2012) and Range Rover Velar. Engineered to meet Land Rover's material and durability standards, it handles sustained oil pressure and temperature cycling without degradation. Whether you're addressing an active leak, performing preventative maintenance during a service, or rebuilding your cooling circuit, this gasket delivers the reliability and longevity you expect from premium OEM-equivalent parts. What's Included 📦 1x Oil Cooler Gasket LR010770 specification Product Highlights OEM-equivalent material formulation for Land Rover 3.0L V6 and 5.0L V8 engines Part Number LR010770—direct factory match, no cross-reference needed Prevents oil weeping and cooler assembly leaks under sustained pressure and heat Maintains oil flow and thermal efficiency critical to engine longevity Precision-molded geometry ensures factory-tight seal without shimming or modification Compatible with both 3.0L V6 and 5.0L V8 cooler assemblies across model range Tested for vibration, pressure cycling, and extended thermal duty Straightforward replacement during routine cooling system service or repair 1-year manufacturer's warranty and 30-day money-back guarantee Ships worldwide via DHL, FedEx, UPS, TNT—tracked delivery to your door Compatibility Vehicle & Engine Years Fit Land Rover Discovery 4 (3.0L V6) 2010– Direct Fit Land Rover Range Rover Sport (3.0L V6) 2014– Direct Fit Land Rover All-New Discovery (3.0L V6) 2017– Direct Fit Land Rover Range Rover (5.0L V8) 2010–2012 Direct Fit Land Rover Range Rover Velar (5.0L V8) 2017– Direct Fit Land Rover Range Rover Sport (5.0L V8) 2010–2013 Not Compatible Other Land Rover / Range Rover engines — Not Compatible Verify fitment: Cross-check your vehicle's part number (stamped on the cooler assembly or visible in your service record) against LR010770 before purchase. If unsure, contact us with your VIN—we'll confirm compatibility at no charge. Installation Notes Difficulty: Intermediate | Time: 1–2 hours Safety first: Disconnect the negative battery terminal and allow the engine to cool completely. Warm oil under pressure is a burn hazard. Drain: Place a drain pan beneath the oil cooler. If the vehicle is low on oil, drain the system or prepare to catch spillage. Remove cooler assembly: Unbolt the oil cooler from its mounting bracket (typically 2–4 bolts, depending on engine variant). Disconnect any oil lines with care—have rags ready. Separate cooler housing: The gasket sits between the cooler core and end cap. Remove the fastening bolts, gently pry the cap away, and lift out the old gasket. Clean mating surfaces: Wipe both sides with a lint-free cloth and mineral spirits. Remove all old gasket material, oil residue, and debris. A gasket scraper helps; avoid scratching aluminum. Install new gasket: Position the LR010770 gasket onto the cooler core, ensuring correct orientation (check your parts manual or the gasket itself for flow-direction arrows if marked). Reassemble: Reattach the end cap or housing and tighten bolts in a star pattern to avoid warping. Do not over-torque; hand-tight plus 1/4 turn is typical. Reinstall cooler: Bolt the assembly back into the engine bay. Reconnect oil lines, hand-tighten fittings, then snug with a wrench. Check for proper routing and no pinching. Refill & bleed: Add fresh oil to the specified level. Start the engine and idle for 30 seconds, then check the oil level and top off if needed. Look for leaks around the cooler assembly. Test run: Drive gently for 5–10 minutes, focusing on smooth acceleration and temperature stability. Stop, allow cooling, and recheck the oil level and cooler seams one final time. ⚠ Important: Never reuse an old oil cooler gasket. Gasket material becomes permanently set and compressed after one thermal cycle—reuse guarantees leaks and waste. Always fit a fresh gasket. If the cooler housing or core shows cracks, corrosion, or internal blockages (indicated by low flow or high backpressure), replacement of the entire assembly may be necessary. Why Choose Victorious for Oil Cooler Gaskets We stock OEM-equivalent gaskets and seals specifically for Land Rover and Range Rover engines, tested and verified by our technical team. Our 30-day money-back guarantee means zero risk—if the gasket doesn't seal your cooler or fit your model, we'll refund your order in full. With 4.9★ ratings from over 12,300 verified buyers and direct support in the UK and worldwide, you get peace of mind every time. Ready to Seal Your Cooler? Stop oil leaks and restore cooling efficiency with the OEM-spec LR010770 gasket. Order now, and take 20% off when you buy any two items with code 22GET20. Shop Oil Cooler Gaskets 30-Day Money-Back Guarantee 1-Year Warranty Worldwide Shipping – DHL, FedEx, UPS 4.9★ from 12,300+ reviews UK Support +44 203 943 9919 Victorious Automotive is not affiliated with, endorsed by, or connected to Jaguar Land Rover Limited, Range Rover, Discovery, Defender, or any subsidiary. All vehicle names, badges, and specifications are used solely for compatibility and reference purposes. This product is an aftermarket OEM-equivalent part. Always verify fitment against your vehicle's original part number before purchase.

```html Victorious · Land Rover LR2 · Cooling System Oil Cooler & Thermostat Radiator Hose Kit – Land Rover LR2 3.2L OEM-spec cooling hoses engineered for Freelancer LR2 and Volvo platforms. Three configurations in OEM-quality rubber. LR2 L359 2008–2012 3.2L Petrol Cooling System Rubber Hose Direct Fit Why Your LR2's Cooling System Matters Land Rover Freelander LR2 and Volvo S60, S80, V60, XC60, and XC90 models with 3.2L petrol engines rely on precision-engineered cooling hoses to manage engine temperature under all conditions. Original hoses age, crack, and degrade, leading to coolant leaks and potential overheating on motorway drives or during summer heat. This OEM-quality hose kit replaces three critical cooling passages: oil cooler outlet to water pump, bottom radiator inlet to water pump, and thermostat to lower radiator. Each hose is manufactured in reinforced automotive rubber, pre-shaped to factory geometry, and supplied with the correct coupling diameters for direct bolt-on fitment. Whether your LR2 has begun seeping or you're performing preventive maintenance before a long journey, these hoses restore cooling efficiency without modification or adaptation. What's Included 🔧 Option A: Oil Cooler Outlet Hose LR005563 / 30774514 – From oil cooler to water pump inlet 🔧 Option B: Bottom Radiator Hose LR005564 / 30774513 – From lower radiator to water pump 🔧 Option C: Thermostat to Lower Radiator Hose LR005566 / 30774512 – From thermostat housing to lower radiator inlet 📋 Full Specifications Card OEM part numbers, interchange references, fitment notes Product Highlights OEM-Spec Geometry – Pre-formed to original Land Rover/Volvo cooling layout Reinforced Automotive Rubber – Rated for 3.2L petrol engine temperatures and pressures Direct Fit Installation – No adapters, modifications, or custom fabrication needed Three Independent Options – Choose single hose or full kit for complete cooling refresh OEM Part Cross-Reference – Works with LR005563, LR005564, LR005566, 30774512–30774514 Volvo S60/S80/V60/XC60/XC90 Compatible – Same 3.2L platform engineering 12-Month Warranty – Full coverage against manufacturing defect Rapid Circulation – Maintains ideal coolant flow under urban and highway stress UK Dispatch – Ships via DHL/FedEx worldwide within 48 hours 30-Day Money-Back Guarantee – Complete confidence on fitment and performance Compatibility Matrix Vehicle Model Engine Year Range Fitment Land Rover Freelander LR2 3.2L Petrol 2008–2012 Direct Fit Volvo S60 3.2L Petrol All Gen 1–2 Direct Fit Volvo S80 3.2L Petrol All Gen 1–2 Direct Fit Volvo V60 3.2L Petrol All Gen 1 Direct Fit Volvo XC60 3.2L Petrol All Gen 1–2 Direct Fit Volvo XC90 3.2L Petrol All Gen 1–2 Direct Fit Other Petrol Engines Diesel / Turbo / Other Any Year Not Compatible Installation Notes Difficulty: Moderate | Time: 45–75 minutes Drain coolant – Open radiator drain plug and catch fluid in a approved container. Do not dispose down drains. Locate hose clamps – Identify failing hoses by visual inspection. Take a photo of the original routing for reference. Release clamps – Use a flathead screwdriver or hose clamp tool to loosen band clamps. Rotate hose gently to break seal. Remove old hose – Carefully extract and inspect coupling points for corrosion or debris. Clean inlet/outlet with a lint-free cloth. Install new hose – Align pre-formed bends to match original geometry. Reuse OEM clamps if undamaged; replace if corroded. Refill coolant – Use approved 50/50 coolant mix (not tap water). Bleed air from system by running engine to operating temperature with heater on. Check for leaks – Inspect all coupling points and clamp zones under idling and light acceleration. Top up reservoir if needed. ⚠ Coolant Safety: Engine coolant is toxic. Always allow the engine to cool fully before opening the radiator. Dispose of old coolant at an approved recycling centre. Never pour into drains or soil. Ready to Restore Cooling Confidence OEM-quality hoses. Direct fitment. 30-day returns. Your LR2 deserves cooling reliability that matches its capability. Shop Radiator Hoses Use code 22GET20 for 20% off any 2 items ✓ 4.9★ / 12,300+ Reviews ✓ 30-Day Money-Back ✓ Worldwide DHL/FedEx ✓ Expert UK Support Victorious Automotive is not affiliated with Land Rover, Range Rover, Jaguar Land Rover, or their parent company. All product names, logos, and brands are the property of their respective owners. This product is an aftermarket replacement part engineered for compatibility only. ```

```html Partsmost · Land Rover LR2 / Volvo 3.2L · Cooling System Oil Cooler & Thermostat Radiator Hose Kit – LR2 & Volvo 3.2L Direct OEM replacement cooling hoses that restore factory integrity and thermal management to your LR2 or Volvo 3.2L petrol engine. LR005563 / LR005564 / LR005566 2008–2012 LR2 Volvo S60 / S80 / V60 / XC60 / XC90 Reinforced Rubber Cooling Hose Assembly Overview The Land Rover LR2 and Volvo models equipped with the 3.2L petrol engine rely on a precision cooling system to maintain optimal operating temperature. Over time, original radiator and oil cooler hoses degrade from heat cycling, UV exposure, and thermal stress—leading to coolant leaks, engine overheating, and potential damage to your engine bay. This OEM-specification hose kit includes three direct-fit cooling lines: the oil cooler outlet hose, the bottom radiator-to-water pump inlet, and the thermostat-to-lower radiator assembly. Each hose is manufactured to match factory dimensions, material composition, and pressure ratings, ensuring seamless integration with your vehicle's original cooling circuit without modification. Manufactured by Partsmost to exacting standards and backed by a 12-month warranty, this kit delivers the reliability and peace of mind you need for daily driving or spirited use. Installation is straightforward for any mechanically inclined owner, or recommended to a qualified technician for best results. What's Included 🔧 Oil Cooler Outlet Hose (LR005563) From oil cooler to water pump inlet. Direct fit, OEM material. 💧 Bottom Radiator Hose (LR005564) Lower radiator-to-water pump inlet. Reinforced rubber construction. 🌡️ Thermostat-to-Lower Hose (LR005566) From thermostat housing to lower radiator. Pressure-rated assembly. Product Highlights OEM Direct Replacement — Engineered to factory specifications; no modifications needed 12-Month Warranty — Full manufacturer coverage against defects and material failure Reinforced Rubber — High-temp resistant, rated for 3.2L petrol engine cycles Multiple Options — Buy single hose or complete three-piece kit to your needs Tested Fitment — Verified on LR2 L359 (2008–2012) and Volvo S60/S80/V60/XC60/XC90 Fast Shipping — Worldwide DHL, FedEx, UPS delivery; typical 5–10 business days Pressure-Rated — Withstands full coolant system pressure without weeping or failure Heat & UV Resistant — Extended life in underhood environment versus standard rubber Cross-Part Compatible — Works with part numbers 30774512/30774513/30774514 No Core Exchange — Keep your old hose; no return required Compatibility Chart Vehicle / Engine LR005563 LR005564 LR005566 Land Rover LR2 L359 (2008–2012) 3.2L Petrol Direct Fit Direct Fit Direct Fit Volvo S60 (2006–2013) 3.2L Direct Fit Direct Fit Direct Fit Volvo S80 (2006–2016) 3.2L Direct Fit Direct Fit Direct Fit Volvo V60 (2010–2018) 3.2L Direct Fit Direct Fit Direct Fit Volvo XC60 (2008–2017) 3.2L Direct Fit Direct Fit Direct Fit Volvo XC90 (2006–2014) 3.2L Direct Fit Direct Fit Direct Fit ⚠️ Before You Order: If your vehicle is not listed above or you are unsure of your 3.2L engine code, contact us with your VIN. We'll confirm fitment and cross-reference any alternative part numbers to ensure you receive the correct hose assembly. Installation Notes Difficulty Level: Intermediate | Time: 1–2 hours Prepare & Drain: Allow engine to cool fully. Open coolant drain plug and catch fluid in a suitable container. Remove radiator cap to relieve system pressure safely. Remove Old Hoses: Locate the three hoses: oil cooler outlet (top), lower radiator-to-pump inlet (undercarriage), and thermostat-to-lower assembly. Loosen hose clamps using a screwdriver or hose clamp pliers and slide each hose off its barbed connector. Inspect Connections: Clean any residual coolant or corrosion from all barbed fittings. Check for damage to plastic connectors; replace if cracked or brittle. Install New Hoses: Slide each new hose onto its fitting until fully seated. Hand-tighten hose clamps, then use a screwdriver to tighten securely but not over-tight; aim for firm without crushing the hose. Refill & Bleed: Pour fresh coolant into the radiator, filling to the "max" mark. With the radiator cap off, run the engine at idle for 3–5 minutes to circulate coolant and release trapped air. Top up as needed, then reinstall the radiator cap. Test for Leaks: Allow the engine to cool, then inspect all three new hose connections for seeping or dripping. Run the engine again briefly and recheck. No coolant leaks should be visible. Monitor Temperature: On your next short drive, confirm that the engine temperature gauge remains stable and the cooling fans cycle normally. If overheating occurs, stop and recheck hose seating. ⚠️ Important Safety Notes: Never remove the coolant cap from a hot engine; coolant can spray and cause severe burns. Always allow at least 30 minutes of cooling time before work. If you are uncomfortable with cooling system work, have a qualified mechanic perform the installation. Incorrect hose seating can cause coolant loss and engine damage. Ready to Restore Your Cooling System? Stop guessing whether your hoses will fail in traffic. This genuine OEM-spec hose kit gives you factory reliability, a 12-month warranty, and peace of mind every time you drive your LR2 or Volvo 3.2L. Shop This Kit Now Use code 22GET20 for 20% off any 2 items in one order 30-day money-back guarantee Worldwide DHL, FedEx, UPS shipping 4.9★ rating from 12,300+ reviews +44 203 943 9919 Mon–Fri 9am–7pm Disclaimer: This product is not affiliated with, endorsed by, or manufactured by Jaguar Land Rover Limited, Volvo Car Corporation, or their subsidiaries. All vehicle names and logos are trademarks of their respective manufacturers. This product is designed as an aftermarket direct replacement only. Always verify fitment with your VIN before purchase. Victorious Automotive is an independent retailer of automotive parts and accessories. ```

Victorious Automotive · Land Rover / Volvo Cooling · Radiator Hoses Premium Engine Cooling Radiator Hose Kit – LR2 / Volvo 3.2L Petrol Factory-specification coolant hoses engineered to maintain precise engine temperature and prevent overheating under demanding driving conditions. Land Rover LR2 Volvo S60 / S80 / V60 / XC60 / XC90 2008–2012 3.2L Petrol Direct Replacement Rubber Compound Overview The cooling system in your Land Rover LR2 or Volvo S60/S80/V60/XC60/XC90 operates under constant thermal stress. Aged or failing radiator hoses compromise coolant circulation, risking engine damage, overheating, and costly repair bills. This premium OE-specification hose kit restores factory-correct flow paths and thermal stability. We offer three individual hose options or a complete three-piece set, allowing you to replace only what's needed or refresh the entire cooling circuit. Each hose is engineered to Partsmost's exacting OE standards, using high-grade rubber compounds that resist cracking, permeation, and collapse under pressure. Direct bolt-on fitment. No modifications required. Works seamlessly with stock thermostats, water pumps, and radiators. Backed by 12-month warranty and our 30-day money-back guarantee. What's Included 🔧 Option A: Oil Cooler Outlet Hose (LR005563) From oil cooler to main loop. Part No. 30774514. 🔧 Option B: Lower Inlet Hose (LR005564) Bottom radiator to water pump inlet. Part No. 30774513. 🔧 Option C: Thermostat to Radiator Hose (LR005566) Engine thermostat to lower radiator. Part No. 30774512. 📦 Complete Set: All Three Hoses LR005563 + LR005564 + LR005566 for total system refresh. Product Highlights OE-Specification Rubber Compound – Resists cracking, permeation, and thermal fatigue Direct Fit – No modifications; bolt straight onto OEM water pump and radiator ports Factory Part Numbers – LR005563, LR005564, LR005566 + Volvo interchanges Pressure-Rated – Engineered to handle peak coolant system pressure safely Crimped Connections – Secure hose-to-fitting integrity; no leaks or weeping Temperature Stable – Maintains flexibility from −40°C to +120°C operating range Proven Reliability – Trusted by Land Rover Freelander LR2 and Volvo owners globally Easy Identification – Colour-coded and embossed part numbers for quick assembly Fuel Inert – Rubber formulation resists ethanol and modern fuel additives 12-Month Warranty – Full coverage against manufacturing defects Vehicle Compatibility Vehicle Model Years Engine Fit Status Land Rover Freelander LR2 2008–2012 3.2L Petrol Direct Fit Volvo S60 2008–2012 3.2L Petrol Direct Fit Volvo S80 2008–2012 3.2L Petrol Direct Fit Volvo V60 2008–2012 3.2L Petrol Direct Fit Volvo XC60 2008–2012 3.2L Petrol Direct Fit Volvo XC90 2008–2012 3.2L Petrol Direct Fit Other engines / years — Non-3.2L Not Compatible Always verify your vehicle VIN and engine code before purchase. We offer free fitment checks: email your VIN to our team at +44 203 943 9919 (Mon–Fri 9am–7pm) or use our online chat. Installation Guide Difficulty Level: Intermediate | Time: 1–2 hours Drain cooling system: Remove radiator cap, open drain plug, and let coolant flow into a drain pan. Dispose responsibly. Locate hose routes: Identify which hose(s) you're replacing. Consult factory diagrams for port locations and clamp positions. Loosen hose clamps: Use a flat-head or Phillips screwdriver to unscrew hose clamps at each end of the old hose. Remove old hose: Gently twist and pull the old hose free from water pump and radiator fittings. Note the routing path. Fit new hose: Push new hose firmly onto each port until fully seated. Rotate 90° to ensure no stress on clamps. Secure clamps: Position clamps approximately 6–12 mm from hose end. Tighten evenly (do not over-torque; snug is sufficient). Refill coolant: Pour fresh 50/50 coolant into radiator until full. Replace radiator cap and run engine at idle for 2–3 minutes. Check for leaks: Inspect each clamp connection and hose body for seeping. Top up coolant level if required. Reset heater: Turn on climate control to purge air locks from the system. Allow engine to reach operating temperature before driving. Important: Allow engine to cool completely before beginning work. Hot coolant can cause severe burns. Dispose of old coolant at an approved recycling centre—never pour down drains. Keep antifreeze away from children and pets. Ready to Restore Cooling Reliability? OE-specification hoses. Factory part numbers. 12-month warranty. Order your radiator hose kit today and enjoy peace of mind knowing your LR2 or Volvo cooling system is operating at peak efficiency. Shop Radiator Hose Kit Use code 22GET20 for 20% off any 2 items. ✓ 30-day money-back guarantee ✓ 4.9★ rated – 12,300+ verified reviews ✓ Fast worldwide shipping – DHL, FedEx, UPS, TNT ✓ Expert support – +44 203 943 9919 Victorious Automotive is an independent aftermarket specialist and is not affiliated with or endorsed by Land Rover, Range Rover, Jaguar Land Rover (JLR), Volvo, or any OEM manufacturer. All vehicle names and logos are trademarks of their respective owners. Product compatibility and fitment are provided as guidance only; always verify VIN and engine code before purchase. We are not responsible for incorrect fitment or modifications made to vehicles.

```html Victorious · Land Rover LR2 · Cooling System Oil Cooler Outlet Radiator Hose Set for Land Rover LR2 Factory-spec coolant hoses designed to maintain optimal engine temperature and system integrity on your Land Rover Freelander LR2. LR2 L359 2008–2012 3.2L Petrol Direct Fit OE Rubber Compound Cooling System Overview The Land Rover Freelander LR2 (2008–2012) with 3.2L petrol engines relies on a precision cooling system where every hose connection matters. Over time, factory radiator hoses degrade, leak, and lose their seal—compromising coolant flow, engine temperature regulation, and overall system reliability. This Direct Replacement Radiator Hose Set restores OE performance with materials engineered to handle high-pressure coolant cycles and temperature fluctuations. Our hose set includes three factory-specification segments: oil cooler outlet line, bottom-to-water-pump inlet, and thermostat-to-radiator lower hose. Each hose is manufactured to original equipment dimensions, wall thickness, and rubber compound specification, ensuring perfect fit and durability across your LR2's cooling circuit. Whether you're replacing worn hoses as preventive maintenance or addressing a leak, this comprehensive three-piece set eliminates the need for multiple sourcing and guarantees compatibility across the entire front cooling system. Backed by a 12-month warranty and Victorious's 30-day money-back guarantee, you can install with confidence. What's Included 🔧 Oil Cooler Outlet Hose (LR005563) From oil cooler to transmission cooler inlet 💧 Lower Water Pump Inlet (LR005564) Bottom radiator to water pump inlet line 🌡️ Thermostat to Radiator Hose (LR005566) Engine thermostat housing to lower radiator ✓ All Hoses OE Specification Engineered to factory pressure and temp ratings Product Highlights Direct Replacement for OEM Hoses – No modification required OE-Grade Rubber Compound – Built for 3.2L petrol engine demands Factory Dimension & Wall Thickness – Pressure-rated for LR2 cooling circuit Three-Piece Complete Set – Oil cooler, water pump, thermostat segments High-Temperature Resistant – Handles sustained coolant flow cycles Sealed Connections – Prevents leaks and air ingress Easy Installation – No special tools or clips required 12-Month Warranty – Manufacturer defect coverage Tested for Durability – Withstands vibration and engine heat Cost-Effective vs. Separate Hoses – Save on sourcing time and shipping Compatibility Vehicle Year Range Engine OEM Part # Status Land Rover Freelander LR2 (L359) 2008–2012 3.2L Petrol LR005563 / LR005564 / LR005566 Direct Fit Volvo S60 / S80 / V60 / XC60 / XC90 2006–2015 3.2L Petrol 30774514 / 30774513 / 30774512 Compatible Land Rover LR2 (Other model years) 2007, 2013+ Any Engine — Not Compatible Range Rover Sport / Evoque / Discovery Any Any — Not Compatible ⚠️ Always verify your VIN and original part number before purchase. Send us your 17-digit VIN and we'll confirm fitment at +44 203 943 9919 (Mon–Fri 9am–7pm). Installation Guide Radiator Hose Replacement – Cooling System Service Preparation: Allow engine to cool completely. Disconnect negative battery terminal. Position drain pan under radiator. Drain Coolant: Open radiator drain plug (lower right side). Allow full drainage into container. Close drain plug when empty. Remove Old Hoses: Unbolt hose clamps at both ends using socket wrench or adjustable wrench. Gently twist and pull hoses free. Note clamp positions. Clean Connection Points: Wipe radiator, water pump inlet, and thermostat housing with lint-free cloth. Remove old rubber debris. Install New Hoses: Slip new hoses onto ports. Ensure full seating (hose should sit 1/4" from port edge). Hand-tighten clamps first. Secure Clamps: Torque hose clamps to 15–20 N·m (11–15 lb-ft). Do not over-tighten or you may crack ports. Refill Coolant: Pour recommended coolant (check owner's manual for type) until radiator is full. Start engine and allow air to bleed naturally. Final Check: Run engine for 10 minutes at idle. Check for leaks around all hose connections. Top up coolant if needed. Safety Note: Do not open radiator cap or remove hoses while engine is hot. Pressurized coolant can cause severe burns. Always work on a cold engine. Ready to Restore Your LR2's Cooling System? Don't let failing radiator hoses compromise your Land Rover's reliability. Our OE-spec hose set is engineered for your LR2 and backed by Victorious's 30-day money-back guarantee and 12-month manufacturer warranty. Shop Radiator Hose Set Save 20% on any 2 items with code 22GET20 4.9★ 12,300+ verified reviews ✓ 30-Day Money Back ✓ 12-Month Warranty ✓ Worldwide Shipping Questions? Contact us: +44 203 943 9919 (Mon–Fri 9am–7pm GMT) or email support@victorious.shop Victorious Automotive is not affiliated with, endorsed by, or connected to Land Rover, Jaguar Land Rover, or any affiliated brands. All vehicle names, logos, and designations are property of their respective manufacturers. This product is a third-party replacement part designed for compatibility. Always consult your vehicle's service manual or contact a certified Land Rover technician with questions about fit or installation. ```

SPECIFICATIONSBrand Name: PartsmostCondition: NewHigh-concerned chemical: noneManufacturer Part Number: LR077674 AJ811445 ERR4598OEM NO.: LR077674Origin: De(origin)Warranty: 12 months NEW GENUINE OIL REGULATOR NON RETURN VALVE FOR LAND ROVER RANGE ROVER 2010-2012 / RANGE ROVER SPORT 2014- / DISCOVERY SPORT 2015- / ALL NEW DISCOVERY 2017- / RANGE ROVER VELAR 2017- / FOR JAGUAR XK 2006-2014 / XF 2009-2015 / XJ 2010-2019 / XF 2016- /  E-PACE 2017- OE NO.: AJ811445 ERR4598 LR077674   PRODUCT DESCRIPTION: 1) OE quality, OEM quality or Aftermarket brand parts for your choice. 2) According to the original equipment specifications. 3) Perfect match with the original car. 4) Easy and fast installation. 5) Stable performance and high reliability.   ITEM TYPE: Oil Regulator Non Return Valve PART NUMBERS: LR077674 AJ811445 ERR4598 COMPATABILITY: FOR LAND ROVER DEFENDER 1987-2006 FOR LAND ROVER DISCOVERY 2 1998-2004 CLASSIC 2.5L 5 CYLINDERS TURBOCHARGER DIESEL ENGINES FOR LAND ROVER RANGE ROVER 2010-2012 5.0L OHC SGDI NA V8 PETROL ENGINES FOR LAND ROVER RANGE ROVER SPORT 2014- 3.0 I6 TURBO DIESEL (AJ20D6) ENGINES FOR LAND ROVER DISCOVERY SPORT L550 2015- 2.0 TURBO PETROL (AJ200P) ENGINES FOR LAND ROVER ALL NEW DISCOVERY 2017- FOR LAND ROVER RANGE ROVER VELAR 2017- 3.0 I6 TURBO PETROL (AJ20P6) ENGINES FOR JAGUAR XK 2006-2014 5.0L V8 FOR JAGUAR XF 2009-2015 3.0L FOR JAGUAR XJ 2010-2019 5.0L V8 FOR JAGUAR XF 2016- 3.0L FOR JAGUAR E-PACE 2017- 2.0L DIESEL   PACKAGE INCLUDED: 1 x Oil Regulator Non Return Valve   PRODUCT PHOTOS: Please note the packaging and the stickers might be updated by the manufacturer, but the photos might not be updated at the same time. We only guarantee the product quality is the same. If you find that the product images are the same as ours but without our brand logo "Partsmost", it means that other merchants have stolen our product images. Please note that if you purchase from other merchants, you will bear the risks. OE quality: SKETCH MAP:   Technical Data Will this item fit your vehicle? - Before purchasing, please pay attention to item Technical Data and check Part Numbers. Make sure that one of these part numbers does coincide with the number of your previous part or does replace your Original Equipment Number. - Surely, in case you doubt in fitment, cannot find the number of your previous part listed in Part Numbers section, or just cannot be sure about item compatibility with your vehicle, please send us your VIN number (Vehicle Identification Number) which is on your Vehicle Registration Certificate or the lower left corner of the front windshield. We are here to assist you to check. - Let's avoid compatibility issues, returns, and get great shopping experience ever! Payment Method - You can see all payment methods available and choose the one you prefer. - If you cannot find the payment method you prefer, please contact us to get more information. - We offer combined packages shipping discount. If you purchase more than one item or in big quantity of some items, please feel free to ask us before you make payment how to save shipping cost for you. Shipping Method & Delivery Time - We usually use Standard shipping method or Simple shipping method to send goods by Free Shipping. If you have a special requirement, please contact us before you purchase. Tracking numbers will be available to be checked at www.17track.net after the packages have been shipped out. Seller's shipping method to Brazil usually refers to "Correios Brazil" and the tracking number can be checked. Delivery time is about 25 days to 45 days. - We can also use Express shipping method like e-EMS, EMS, DHL, FedEx, UPS to send goods if you need urgently, but please note that you may need to pay import duty and taxes based on the Customs policy of your country. Our selling price does NOT include any Customs charges and local charges! - If you do not want to pay import duties, please contact us, and we will check if there are any duty-free shipping methods are available to your country. NOTE: - In some remote countries like Bosnia and Herzegovina, Bolivia, Dominican Republic, South Africa etc., buyers usually can get goods within 60 natural days, but if severe Custom Invesigation happens, delivery time may extend to 100 natural days. - China Post is slower than other standard post shipping method and sometimes its delivery time is longer than 60 days, so we do NOT recommend it if you have not patience to wait for that long time. Please do NOT open any disputes for the reason of "goods still in delivery" if you choose China Post. Returns - Customers may return an item for refund or exchange within 10 days after the item is received. If return is for any quality problems, we pay return charges. If return is NOT for any quality problems, the buyer should pay return charges. Moreover, items must be returned in their original shipping method and intact packaging is required. Otherwise, you might not get full refund. - If the package is returned to us for the reason as below, the buyer need to pay for return charges if it occurs and CANNOT get a refund of the freight paid for the order. 1. After the parcel arrives at the destination country, the buyer's address, phone number, zip code is not clear and the buyer cannot be contacted; 2. The buyer did not sign and receive the package in time; 3. The buyer refused to receive the package; 4. The buyer refused to pay import duty and taxes. About us - We are a professional seller of auto spare parts for British and European car models located in China for more than 10 years, the biggest producing country. With the good quality products we have, we do competitive offer, professional service to customers all over the world. - We choose the suitable shipping way for every country those we ship to. Usually we ship out goods within 2 working days, sometimes within 3 working days during the promotion period. We give satisfy solution to any problems we meet. - We also do business of original parts and OEM brand parts to provide more alternatives for our customers. If you are also interested in them, just feel free to get a quotation from us. - We welcome wholesale orders and we can ship goods by sea, please contact us for more information. Feedbacks - Once we have received your order, a positive feedback will be automatically sent to you. Please let us to know if you have not received our feedback, we will give feedback manually. - We would also greatly appreciate if you leave us a positive feedback with 5 stars rating. - If you feel that we deserve a neutral or negative feedback, please, CONTACT US before leaving any feedback, give us a chance to make things right and leave your impression most positive!

Victorious · Range Rover Evoque · Suspension Front Suspension Control Arm Bushing — Range Rover Evoque L538 OE-spec replacement bushing restores steering precision and eliminates clunking noise on Evoque models from 2012 onwards. L538 / L551 2012–2026 Rubber / Polyurethane Composite Direct Fit Suspension Bushings Overview The Range Rover Evoque's front suspension geometry depends entirely on tight, responsive control arm bushings. When these wear—typically between 40,000–80,000 miles—the steering becomes notchy, the ride feels loose, and you may notice audible clunking from the front end over bumps. This front suspension control arm bushing is the larger of the two bushings on each control arm, and it's where most of the wear concentrates. This is a genuine Partsmost replacement, manufactured to OE dimensions and material specifications for the Evoque L538 (2012–2022) and L551 (2023+). Part numbers LR078656 (right) and LR078657 (left) confirm exact fitment. Unlike aftermarket rubber, our composite formulation resists age-related hardening and maintains compliance across temperature ranges. Restoring this bushing improves steering feedback, reduces suspension noise, and prevents accelerated wear to the ball joints and tie rod ends. A single bushing replacement typically takes 60–90 minutes per side with basic hand tools and a lift. What's Included 🔧 1× Control Arm Bushing Larger outer bushing — left or right 📋 Fitment Guide Part number cross-reference & torque specs ✅ 30-Day Money-Back Guarantee Full refund if you're not satisfied 🌍 Worldwide Shipping DHL, FedEx, UPS, TNT — 5–7 days Product Highlights OE-specification dimensions & material durability Eliminates suspension clunking and steering play Works on both L538 (2012–2022) and L551 (2023+) models Rated for 80,000+ miles under normal conditions Resists UV and thermal degradation vs. standard rubber Left and right application — see part numbers below Professional-grade fit — no modification required Improves steering response and cornering confidence Backed by Victorious 30-day guarantee Same part used by Land Rover dealers globally Compatibility Model Years Part Number Position Status Range Rover Evoque L538 2012–2022 LR078656 Right Side Direct Fit Range Rover Evoque L538 2012–2022 LR078657 Left Side Direct Fit Range Rover Evoque L551 2023–2026 LR078656 Right Side Direct Fit Range Rover Evoque L551 2023–2026 LR078657 Left Side Direct Fit Other Land Rover / Range Rover models All years — — Not Compatible Note: One bushing is included per order. Most Evoque owners purchase two (one per side) to maintain even suspension response. Order left and right together for best results. Installation Notes Difficulty: Intermediate | Time: 60–90 min per side Lift the vehicle on jack stands and remove the wheel on the side you're working. Remove the control arm bolt that passes through the bushing. You may need to support the arm with a hydraulic jack. Extract the old bushing using a press, bearing puller, or carefully with a hammer and drift. The bushing is press-fit. Clean the bore in the control arm of any debris or rust. Press the new bushing squarely into place using a press or installation sleeve. Do not force it by hand. Reinsert the control arm bolt and torque to 85 Nm (63 lbf-ft). Lower the vehicle and test suspension compliance over a bump. Perform a wheel alignment to reset toe-in after suspension work. Warning: Pressing bushings incorrectly can crack the control arm. If you lack a press, we recommend having a qualified Land Rover technician handle this work. Improper installation voids the guarantee. Ready to Restore Your Evoque's Suspension? Reclaim steering precision and eliminate annoying suspension noise. Our Partsmost control arm bushings are proven on thousands of Evoque models worldwide, backed by our 30-day money-back guarantee and premium customer support. Shop Range Rover Evoque Parts Use code 22GET20 for 20% off any 2 items. 4.9 / 5 — 12,300+ verified reviews ✓ 30-day guarantee ✓ Worldwide shipping 📞 +44 203 943 9919 — Mon–Fri 9am–7pm Victorious Automotive is an independent aftermarket specialist and is not affiliated with Land Rover, Range Rover, Jaguar, or Jaguar Land Rover plc. All vehicle names, logos, and trademarks are the property of their respective manufacturers. Product descriptions and compatibility information are provided for reference only and do not constitute endorsement by any manufacturer.

Victorious Automotive · Toyota Land Cruiser 250 · Exterior Trim Outside Door Handle Decoration Covers for 2024 Toyota Land Cruiser 250 LC250 1958 — Carbon Fibre, Electroplating & Black Precision-moulded ABS door handle covers that elevate the exterior character of the 2024 Land Cruiser 250, available in carbon fibre pattern, electroplating chrome, and classic gloss black finishes. LC250 2024 ABS Material Carbon Fibre Pattern Electroplating Finish Gloss Black No-Drill Install Exterior Trim Door Handles OEM-Style Fit Overview The 2024 Toyota Land Cruiser 250 — internally known as the LC250 — is a landmark re-engineering of one of the world's most respected off-road platforms. With its bold, heritage-inspired stance and updated proportions, the LC250 invites owners to personalise and protect every surface detail. The door handles, being one of the most frequently touched exterior components, are both a focal point and a vulnerability when it comes to daily wear and micro-scratching. These outside door handle decoration covers are designed specifically for the 2024 Land Cruiser 250 body architecture, overlaying each original handle cup with a precisely contoured shell that enhances the visual finish while guarding the underlying paintwork. Whether you choose the sporty depth of the carbon fibre pattern, the premium lustre of the electroplating finish, or the understated authority of gloss black, each cover is moulded in high-grade ABS plastic for long-term rigidity and resistance to UV degradation. Installation is adhesive-based and entirely non-destructive — no drilling, no permanent modification. A full set of covers for all doors is included, ensuring a consistent, cohesive look across the entire vehicle. For LC250 owners who take their exterior presentation seriously, these covers are a smart, low-effort upgrade that pays dividends every time you approach the vehicle. What's Included 🚪 Full Set of Door Handle Covers All four doors covered — front and rear, driver and passenger 🔧 Pre-Applied Adhesive Tape 3M-grade automotive adhesive backing for clean, secure bonding 🧽 Cleaning Prep Wipe Alcohol prep wipe for surface degreasing prior to installation 📋 Installation Guide Step-by-step instructions included in the box Product Highlights Precision-moulded specifically for the 2024 Toyota Land Cruiser 250 door handle geometry Three distinct finishes: carbon fibre pattern, electroplating chrome, and gloss black High-grade ABS construction — impact-resistant, UV-stable, and weather-sealed Protects original paintwork from key scratches, nail marks, and daily contact abrasion Adhesive installation — no drilling, no permanent alteration to factory panels Full vehicle coverage — all four door handles included in a single set Electroplating finish adds a premium chrome-like lustre that complements factory brightwork Carbon fibre pattern delivers a motorsport-inspired aesthetic with tactile visual depth Lightweight construction adds negligible mass while meaningfully improving exterior detail Colour-stable finish resists fading, chalking, and peeling in extreme climates Compatibility Vehicle Year Range Trim / Grade Fitment Toyota Land Cruiser 250 (LC250) 2024 All Grades (GX, VX, ZX, 1958 Edition) Direct Fit Toyota Land Cruiser 300 (LC300) 2022–2024 All Grades Not Compatible Toyota Land Cruiser 200 (LC200) 2008–2021 All Grades Not Compatible Toyota Land Cruiser Prado 150 2010–2024 All Grades Not Compatible Toyota 4Runner (5th Gen) 2010–2024 All Grades Not Compatible Installation Notes 🛠 Difficulty: Easy  |  ⏱ Estimated Time: 20–30 Minutes  |  🔩 Tools Required: None Thoroughly wash and dry all four door handle areas to remove road grime, wax residue, and grease. The cleaner the surface, the stronger the bond. Use the included alcohol prep wipe to degrease each handle recess. Allow to dry completely for at least 60 seconds before proceeding. Test-fit each cover dry (without removing the adhesive backing) to confirm orientation and alignment before committing to placement. Peel back the adhesive liner and carefully position the cover over the door handle, starting from one end to avoid trapped air bubbles. Press firmly into place along the full perimeter. Apply firm thumb pressure to all edges and contoured sections for 30–60 seconds to activate the adhesive bond fully. Allow the adhesive to cure for a minimum of 12–24 hours in dry conditions before washing the vehicle or exposing it to heavy moisture. ⚠ Important: Do not install in temperatures below 10°C (50°F) — cold conditions significantly reduce adhesive activation and initial bond strength. Avoid installation in direct sunlight on hot bodywork, as this can cause the adhesive to cure prematurely before full contact is achieved. Finish the Details. Own the Exterior. The Land Cruiser 250 is built to go anywhere and look formidable doing it. These door handle covers are a small investment that protects original paintwork and sharpens the exterior finish in a single fit. Trusted by over 12,300 verified customers worldwide — shop with complete confidence. Shop All LC250 Exterior Accessories Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 🌍 Worldwide Shipping via DHL, FedEx, UPS & TNT ↩ 30-Day Money-Back Guarantee 📞 +44 203 943 9919 Mon–Fri, 9am–7pm Victorious Automotive is an independent aftermarket accessories retailer. This product is not manufactured by, affiliated with, endorsed by, or approved by Toyota Motor Corporation or any of its subsidiaries. Toyota, Land Cruiser, LC250, and all related model names and designations are registered trademarks of Toyota Motor Corporation. All trademarks remain the property of their respective owners and are referenced solely for vehicle fitment identification purposes.

Victorious Automotive · Toyota LC300 · Exterior Door Handle Decorations for Toyota Land Cruiser 300 LC300 Premium protective trim that elevates the LC300's aesthetic while safeguarding original handles from daily wear. LC300 2021–2024 ABS Material Carbon Fiber / Electroplating / Black Adhesive Install Overview The Toyota Land Cruiser 300 represents the pinnacle of off-road refinement and capability. Its proportions demand exterior details that match the engineering beneath. These door handle decorations transform a utilitarian component into a considered design accent—available in three finishes to suit your LC300's aesthetic direction. Engineered from premium ABS material, each set protects your original handles from scratches, UV degradation, and fingerprints while delivering an immediate visual upgrade. Whether you favour the modern geometric appeal of carbon fibre, the polished elegance of electroplating, or the understated aggression of matte black, these covers integrate seamlessly with the LC300's factory lines. Installation is straightforward—clean, align, and secure via precision adhesive. Customised to fit LC300 door handle geometry exactly, these are not generic trim pieces. They're a purposeful upgrade for owners who understand that every detail counts. What's Included 🎨 Complete Set Full LC300 door handle coverage 📋 Installation Guide Step-by-step with diagrams 🧼 Preparation Pads For surface conditioning Product Highlights Three premium finish options: Carbon Fibre Pattern, Electroplating, Matte Black Precision-engineered ABS construction for durability and flexibility Engineered specifically for LC300 door handle geometry (2021–2024) UV-resistant material resists fading in extreme climates Protective barrier against scratches, scuffs, and daily wear Adhesive system rated for temperature extremes (–20°C to 60°C) Maintains factory aesthetics—no drilling or modification required Reversible installation with no permanent changes to vehicle Anti-fingerprint coating on select finishes reduces smudging Professional finish matches OEM quality standards Compatibility Model Year Range Fitment Toyota Land Cruiser 300 (LC300) 2021–2024 Direct Fit Land Cruiser 250 (LC250) 2024+ Not Compatible Land Cruiser 200 (LC200) 2008–2020 Not Compatible Installation Difficulty: Beginner | Time: 15–20 Minutes Park the LC300 in a clean, dry, shaded environment. Ensure door handles are cool to the touch. Use the included preparation pad to gently clean door handle surfaces. Remove any dirt, wax, or residue. Dry completely with a soft cloth. Carefully peel the adhesive backing from the first decoration. Position it over the door handle, aligning it with factory lines and panel edges. Press firmly from the centre outward, applying steady pressure for 10–15 seconds to ensure full contact. Repeat for all remaining door handles. Allow adhesive to cure for 24 hours before opening doors forcefully or washing the vehicle. For additional security, you may apply a thin bead of automotive adhesive promoter around the perimeter (optional). Important: Ensure surfaces are completely dry before installation. Moisture will compromise adhesive bond. Clean hands and work area of dust and debris to avoid trapping particles beneath the decoration. Ready to Refine Your LC300 These door handle decorations represent thoughtful attention to detail—the kind that separates intentional builds from standard examples. Protect and elevate simultaneously. Browse LC300 Collection Use code 22GET20 for 20% off any 2 items 4.9/5 — 12,300+ verified reviews ✓ 30-day money-back guarantee ✓ Worldwide shipping via DHL, FedEx, UPS ✓ Support: +44 203 943 9919 (Mon–Fri 9am–7pm) Disclaimer: Victorious Automotive is an independent aftermarket accessory specialist. We are not affiliated with, endorsed by, or connected to Toyota Motor Corporation, Land Rover, Jaguar Land Rover, or any OEM manufacturer. All product names and vehicle model designations are the property of their respective owners and are used solely for identification and compatibility purposes. Installation of aftermarket accessories may affect vehicle warranty; consult your dealer before modification. We recommend professional installation if you are unsure. All sales are final unless covered by our 30-day money-back guarantee.

Consigue estos alerones traseros para tu parachoques Clase A. Fácil de colocar. Los hacemos en rojo y negro. Tipo de artículo: Parachoques Altura del artículo: 11 cm Características especiales: Proteger Año del modelo: 2013-1016 Modelo de coche: Mercedes Benz W176 A200 A250 A45 AMG Longitud del artículo: 40 cm Peso del artículo: 549 g Nombre del modelo: Parachoques Tipo de material: ABS Ancho del artículo: 25 cm Nombre de la marca: Autoleader Envíos a todo el mundo

A todos nos encanta que nuestra llave Landrover esté sana y salva, contra derrames y caídas. Este exclusivo estuche para llaves de Landrover garantizará que su llave se mantenga elegante pero sana y salva. Los llaveros de Landrover y Jaguar siempre tienen el problema de que el plástico de la cubierta del control remoto se desprenda; puede evitar que esto suceda y proteger los componentes electrónicos de la llave usando esta cubierta. Tipo de material: TPU Color: Dorado Gris Plata Rosa Material: Excelente aleación de aluminio Marca del coche: Para Land Rover 2018 ENVÍO AL MUNDO ENTERO PAGO SEGURO GARANTIZADO

SPECIFICATIONSBrand Name: PartsmostCondition: NewFitment Type: Direct ReplacementHigh-concerned chemical: noneModel Number: LR023777 REPAIR KITOrigin: Mainland China NEW PVC VALVE SERVICE KIT OF VALVE COVER LR023777 31319642 REPAIR KIT FOR 3.2L PETROL ENGINE LAND ROVER FREELANDER LR2 VOLVO XC60 XC70 XC90 S80 V70   PRODUCT DESCRIPTION: 1) OE quality, OEM quality or Aftermarket brand parts for your choice. 2) According to the original equipment specifications. 3) Perfect match with the original car. 4) Easy and fast installation. 5) Stable performance and high reliability.   ITEM TYPE: PVC VALVE SERVICE KIT PART NUMBERS: FOR VALVE COVER LR023777 / 31319642   COMPATABILITY: FOR LAND ROVER FREELANDER LR2 FOR VOLVO XC60 XC70 XC90 S80 V70 3.2 L Petrol Engines   Please note the part numbers and compatibility are only for reference! May fit other models but please check first!   PACKAGE INCLUDED: 2 x PVC VALVE SERVICE KIT   PRODUCT PHOTOS: If you find that the product images are the same as ours but without our brand logo "Partsmost", it means that other merchants have stolen our product images. Please note that if you purchase from other merchants, you will bear the risks.Aftermarket brand parts: This is not genuine parts. CN Brand-2 sets: SKETCH MAP:   Technical Data Will this item fit your vehicle? - Before purchasing, please pay attention to item Technical Data and check Part Numbers. Make sure that one of these part numbers does coincide with the number of your previous part or does replace your Original Equipment Number. - Surely, in case you doubt in fitment, cannot find the number of your previous part listed in Part Numbers section, or just cannot be sure about item compatibility with your vehicle, please send us your VIN number (Vehicle Identification Number) which is on your Vehicle Registration Certificate or the lower left corner of the front windshield. We are here to assist you to check. - Let's avoid compatibility issues, returns, and get great shopping experience ever! Payment Method - You can see all payment methods available and choose the one you prefer. - If you cannot find the payment method you prefer, please contact us to get more information. - We offer combined packages shipping discount. If you purchase more than one item or in big quantity of some items, please feel free to ask us before you make payment how to save shipping cost for you. Shipping Method & Delivery Time - We usually use Standard shipping method or Simple shipping method to send goods by Free Shipping. If you have a special requirement, please contact us before you purchase. Tracking numbers will be available to be checked at www.17track.net after the packages have been shipped out. Seller's shipping method to Brazil usually refers to "Correios Brazil" and the tracking number can be checked. Delivery time is about 25 days to 45 days. - We can also use Express shipping method like e-EMS, EMS, DHL, FedEx, UPS to send goods if you need urgently, but please note that you may need to pay import duty and taxes based on the Customs policy of your country. Our selling price does NOT include any Customs charges and local charges! - If you do not want to pay import duties, please contact us, and we will check if there are any duty-free shipping methods are available to your country. NOTE: - In some remote countries like Bosnia and Herzegovina, Bolivia, Dominican Republic, South Africa etc., buyers usually can get goods within 60 natural days, but if severe Custom Invesigation happens, delivery time may extend to 100 natural days. - China Post is slower than other standard post shipping method and sometimes its delivery time is longer than 60 days, so we do NOT recommend it if you have not patience to wait for that long time. Please do NOT open any disputes for the reason of "goods still in delivery" if you choose China Post. Returns - Customers may return an item for refund or exchange within 10 days after the item is received. If return is for any quality problems, we pay return charges. If return is NOT for any quality problems, the buyer should pay return charges. Moreover, items must be returned in their original shipping method and intact packaging is required. Otherwise, you might not get full refund. - If the package is returned to us for the reason as below, the buyer need to pay for return charges if it occurs and CANNOT get a refund of the freight paid for the order. 1. After the parcel arrives at the destination country, the buyer's address, phone number, zip code is not clear and the buyer cannot be contacted; 2. The buyer did not sign and receive the package in time; 3. The buyer refused to receive the package; 4. The buyer refused to pay import duty and taxes. About us - We are a professional seller of auto spare parts for British and European car models located in China for more than 10 years, the biggest producing country. With the good quality products we have, we do competitive offer, professional service to customers all over the world. - We choose the suitable shipping way for every country those we ship to. Usually we ship out goods within 2 working days, sometimes within 3 working days during the promotion period. We give satisfy solution to any problems we meet. - We also do business of original parts and OEM brand parts to provide more alternatives for our customers. If you are also interested in them, just feel free to get a quotation from us. - We welcome wholesale orders and we can ship goods by sea, please contact us for more information. Feedbacks - Once we have received your order, a positive feedback will be automatically sent to you. Please let us to know if you have not received our feedback, we will give feedback manually. - We would also greatly appreciate if you leave us a positive feedback with 5 stars rating. - If you feel that we deserve a neutral or negative feedback, please, CONTACT US before leaving any feedback, give us a chance to make things right and leave your impression most positive!

Este es un kit de piezas de repuesto interiores de madera de durazno para el Defender 90/110. El juego viene con piezas de repuesto para molduras interiores para; - 4x Cubiertas para molduras de puertas - Madera de durazno - 3X Cubiertas para manijas de puertas - Madera de durazno - Consola central - Madera de durazno - 2x manijas de agarre delanteras Nota: Los artículos anteriores pueden cambiar dependiendo de la variante seleccionada. Asegúrese de seleccionar la variante con el modelo de automóvil que tiene. Nota: seleccione volante a la izquierda o volante a la derecha.

SPECIFICATIONSBrand Name: PartsmostCondition: NewFitment Type: Direct ReplacementHigh-concerned chemical: noneManufacturer Part Number: C2D60916 OR C2D60917Material: MetalOEM NO.: LR160736 OR LR160735Origin: Mainland ChinaPart Number of 3.0 Petrol: LR160736 C2D60916Part Number of 5.0 Petrol: LR160735 C2D60917Warranty: 12 months NEW 3.0L V6 OR 5.0L V8 PETROL SUPERCHARGER ISOLATOR COUPLER FOR LAND ROVER DISCOVERY LR4 / RANGE ROVER 2013- / RANGE ROVER SPORT 2014- / ALL NEW DISCOVERY 2017- / RANGE ROVER VELAR / NEW DEFENDER 2020- / FOR JAGUAR XF 2009-2015 / XJ 2010-2019 / F-TYPE 2014- / XE 2015- / XF 2016- / F-PACE 2016- OE NO.: C2D60916 LR160736 OR C2D60917 LR160735   PRODUCT DESCRIPTION: 1) OE quality, OEM quality or aftermarket parts for your choice. 2) According to the original equipment specifications. 3) Perfect match with the original car. 4) Easy and fast installation. 5) Stable performance and high reliability.   ITEM TYPE: SUPERCHARGER ISOLATOR COUPLER PART NUMBERS: LR160736 C2D60916 OR LR160735 C2D60917 COMPATABILITY: LR160736: FOR LAND ROVER DISCOVERY LR4 2010- FOR LAND ROVER RANGE ROVER SPORT 2014- FOR LAND ROVER ALL NEW DISCOVERY 2017- FOR LAND ROVER RANGE ROVER VELAR 2017- 3.0L DOHC GDI SC V6 PETROL FOR LAND ROVER NEW DEFENDER 2020- 5.0L OHC SGDI SC V8 PETROL FOR JAGUAR XF 2009-2015 FOR JAGUAR XJ 2010-2019 FOR JAGUAR XE 2015- FOR JAGUAR XF 2016- FOR JAGUAR F-PACE 2016- 3.0L V6 PETROL OR LR160735: FOR LAND ROVER RANGE ROVER 2013- FOR LAND ROVER RANGE ROVER SPORT 2014- FOR JAGUAR XF 2009-2015 FOR JAGUAR XJ 2010-2019 AJ133 FOR JAGUAR F-TYPE 2014- AJ133 5.0L OHC SGDI SC V8 PETROL   PACKAGE INCLUDED: You can find the items as below in this item link, but it does not mean you will get all of them. There are several product options with different selling prices in this advertisement link. Please confirm the quantity you will get according to the product option you chose! If any other queries, please ask us before you make the purchase. 1 x SUPERCHARGER ISOLATOR COUPLER   PRODUCT PHOTOS: Please note the packaging and the stickers might be updated by the manufacturer, but the photos might not be updated at the same time. We only guarantee the product quality is the same. If you find that the product images are the same as ours but without our brand logo "Partsmost", it means that other merchants have stolen our product images. Please note that if you purchase from other merchants, you will bear the risks. Aftermarket brand parts-3.0 petrol: Aftermarket brand parts-5.0 petrol: SKETCH MAP: Technical Data Will this item fit your vehicle? - Before purchasing, please pay attention to item Technical Data and check Part Numbers. Make sure that one of these part numbers does coincide with the number of your previous part or does replace your Original Equipment Number. - Surely, in case you doubt in fitment, cannot find the number of your previous part listed in Part Numbers section, or just cannot be sure about item compatibility with your vehicle, please send us your VIN number (Vehicle Identification Number) which is on your Vehicle Registration Certificate or the lower left corner of the front windshield. We are here to assist you to check. - Let's avoid compatibility issues, returns, and get great shopping experience ever! Payment Method - You can see all payment methods available and choose the one you prefer. - If you cannot find the payment method you prefer, please contact us to get more information. - We offer combined packages shipping discount. If you purchase more than one item or in big quantity of some items, please feel free to ask us before you make payment how to save shipping cost for you. Shipping Method & Delivery Time - We usually use Standard shipping method or Simple shipping method to send goods by Free Shipping. If you have a special requirement, please contact us before you purchase. Tracking numbers will be available to be checked at www.17track.net after the packages have been shipped out. Seller's shipping method to Brazil usually refers to "Correios Brazil" and the tracking number can be checked. Delivery time is about 25 days to 45 days. - We can also use Express shipping method like e-EMS, EMS, DHL, FedEx, UPS to send goods if you need urgently, but please note that you may need to pay import duty and taxes based on the Customs policy of your country. Our selling price does NOT include any Customs charges and local charges! - If you do not want to pay import duties, please contact us, and we will check if there are any duty-free shipping methods are available to your country. NOTE: - In some remote countries like Bosnia and Herzegovina, Bolivia, Dominican Republic, South Africa etc., buyers usually can get goods within 60 natural days, but if severe Custom Invesigation happens, delivery time may extend to 100 natural days. - China Post is slower than other standard post shipping method and sometimes its delivery time is longer than 60 days, so we do NOT recommend it if you have not patience to wait for that long time. Please do NOT open any disputes for the reason of "goods still in delivery" if you choose China Post. Returns - Customers may return an item for refund or exchange within 10 days after the item is received. If return is for any quality problems, we pay return charges. If return is NOT for any quality problems, the buyer should pay return charges. Moreover, items must be returned in their original shipping method and intact packaging is required. Otherwise, you might not get full refund. - If the package is returned to us for the reason as below, the buyer need to pay for return charges if it occurs and CANNOT get a refund of the freight paid for the order. 1. After the parcel arrives at the destination country, the buyer's address, phone number, zip code is not clear and the buyer cannot be contacted; 2. The buyer did not sign and receive the package in time; 3. The buyer refused to receive the package; 4. The buyer refused to pay import duty and taxes. About us - We are a professional seller of auto spare parts for British and European car models located in China for more than 10 years, the biggest producing country. With the good quality products we have, we do competitive offer, professional service to customers all over the world. - We choose the suitable shipping way for every country those we ship to. Usually we ship out goods within 2 working days, sometimes within 3 working days during the promotion period. We give satisfy solution to any problems we meet. - We also do business of original parts and OEM brand parts to provide more alternatives for our customers. If you are also interested in them, just feel free to get a quotation from us. - We welcome wholesale orders and we can ship goods by sea, please contact us for more information. Feedbacks - Once we have received your order, a positive feedback will be automatically sent to you. Please let us to know if you have not received our feedback, we will give feedback manually. - We would also greatly appreciate if you leave us a positive feedback with 5 stars rating. - If you feel that we deserve a neutral or negative feedback, please, CONTACT US before leaving any feedback, give us a chance to make things right and leave your impression most positive!

Victorious · Timing Drive · Engine Petrol Timing Chain Guide & Tensioner Kit – AJ200P 2.0T OE-quality complete timing assembly for Land Rover's proven 2.0-litre turbocharged petrol engine. Reliable, direct-fit, 12-month warranty. AJ200P Engine 2014–2019+ Direct Fit OE Standard 9-Piece Kit For Land Rover's Most Trusted Engine The 2.0-litre turbocharged petrol engine (AJ200P) powers some of Land Rover's most capable and refined models. Whether you're running a Range Rover Sport, Discovery Sport, Evoque, or Velar, your timing system is critical to engine health. Over time, the chain guide arms and tensioner wear. Slack chains lead to rattle, misfire, and catastrophic damage. This OE-specification timing chain kit restores factory precision to your engine. It includes all nine components needed for a complete refresh—chain, guide arms (primary and secondary), and tensioner—matched to your exact model variant. Factory engineering. Proven reliability. Partsmost supplies this kit with 12-month warranty and hassle-free returns. If you want to do this job right, this is the kit that does it. What's Included ⛓️ Timing Chain LR091740 primary drive chain 🔄 Primary Guide Arm LR091742 precision-cast 🔄 Secondary Guide Arm LR091743 OEM replacement ⚙️ Timing Tensioner LR093825 hydraulic unit 🔩 Guide Arms (Aux) LR091744–LR091747 set 🛡️ Chain Drive Pulleys LR073760 upgrade tensioner Why This Kit Works OE specification components engineered for AJ200P engines Direct fit—no modification, modification, or adaptation required Hydraulic tensioner maintains optimal chain pressure under load Guide arms reduce friction and chain walk during acceleration 9-piece complete assembly covers all major wear points Fits 2014–2019+ models across Sport, Discovery, Evoque, Velar lines OEM-quality materials: hardened steel chain, precision-cast guides Proven in thousands of engines since 2014 12-month manufacturer warranty included Stable performance under sustained high revs and turbo boost Compatibility Matrix Vehicle Model Code Year Range Fit Status Range Rover Sport L494 2014–2020 Direct Fit Discovery Sport L550 2015–2024 Direct Fit Discovery L462 2017–2024 Direct Fit Range Rover Velar L560 2018–2022 Direct Fit Range Rover Evoque L551 2019–2024 Direct Fit Range Rover Evoque L538 2011–2018 V6 Only Range Rover Vogue L405 2013–2020 V8 Only Defender L663 2020–2024 Not Compatible Engine Requirement: 2.0L Turbo Petrol (AJ200P) only. This kit will not fit V6, V8, or diesel variants. Verify your engine code before purchasing. Installation Notes Difficulty: Advanced | Time: 4–6 hours | Tools: Full engine bay setup Disconnect battery and allow engine to cool for at least 30 minutes. Remove upper engine covers, serpentine belt, and valve cover to expose timing drive housing. Set engine to TDC (Top Dead Centre) using crankshaft pulley marker and timing pin alignment tool. Remove timing chain cover and drain any coolant passages behind it (use catch tray). Unbolt old tensioner and guide arms. Note their orientation; photograph before removal. Slip off old chain from sprockets. Keep sprockets in place (do not rotate crankshaft). Fit new chain onto crank and cam sprockets, ensuring timing marks align perfectly. Install new guide arms in exact OEM position. Use factory torque specs (typically 15–22 Nm for guide fasteners). Install new tensioner and pressurize by rotating crankshaft 2 full turns clockwise. Verify chain slack reduces to <2 mm play. Refit timing cover, valve cover, serpentine belt, and engine covers. Torque all bolts to spec. Reconnect battery, start engine, and listen for smooth chain rattle-free operation. Check for leaks at cover seals. Allow engine to idle 5 minutes and verify timing light confirms correct ignition advance. ⚠️ Critical: Timing work demands precision. One misaligned tooth causes catastrophic engine damage. If unfamiliar with this level of work, have a qualified Land Rover specialist perform installation. We support DIY expertise; we don't support guesswork. Ready to Restore Your Timing Drive? This OE-spec 9-piece timing kit gives your AJ200P engine the precision it demands. Order now, fit with confidence, and run quietly for years to come. Shop Timing Chain Kit Now Save 20% on any 2 items with code 22GET20 at checkout. 4.9★ 12,300+ verified reviews ✓ 30-day money-back guarantee ✓ Worldwide shipping via DHL / FedEx ✓ 12-month manufacturer warranty Victorious Automotive is not affiliated with Land Rover, Range Rover, Jaguar, or Jaguar Land Rover plc. All component numbers, OEM part references, and vehicle codes are cited for compatibility identification only. This product is supplied by Partsmost (China) and carries Partsmost's 12-month warranty. Installation requires professional mechanical expertise. Improper installation may void vehicle warranty. Always verify fitment with your VIN before purchase.

Parte de nuestras piezas de Paquetes interiores de carbono. Actualice el área de ventilación del Range Rover Velar 2017 - 2020 a esta pieza de Fibra de carbono. Fácil instalación Clip sobre la cubierta de ventilación existente. Corte láser perfecto para un ajuste perfecto. Carbohidratos de alta calidad en TPU Consigue el look SVR. Actualice fácilmente el interior de su Range Rover al aspecto de los modelos TOP SVR.

Actualice su Range Rover Velar con estas cubiertas de ventilación plateadas mate. El velar original viene con cubiertas de ventilación de aspecto opaco. Agregar esta pieza aumentará instantáneamente la estética de su Range Rover. ABS de alta calidad Color plata mate Dos piezas (2 piezas) Instalación en menos de 2 minutos Fácil instalación con cinta adhesiva preaplicada Para Velar 2017-2020

Tipo de material: Plástico Porsche Panamera Carman Macann Bobst Cayenne 911 970 981 991 92A 2017 Accesorios para coche Envío a nivel mundial

Funda para llave de coche, carcasa para mando a distancia sin llave Porsche, tapa lateral, protección Fob Tipo de material: Plástico Ajuste: para Porsche Envío al mundo entero

Porsche, carcasa para llave remota Porsche Cayenne Boxster 986 987 Panamera Macan Proteja su control remoto Porsche Tipo de material: TPU Nombre de la marca: liser estilo de coche: estilo de coche color: rojo rosa azul negro oro astilla especial: suave ENVÍO AL MUNDO ENTERO PAGO SEGURO GARANTIZADO  

Descripción de las mercancías: cinturón de coche/cinturón de coche cinturón secundario automático correa de transmisión del coche cinturón de descubrimiento Correa de transmisión del coche Range Rover Correa secundaria automática Range Rover Sport El cinturón secundario automático para vehículos LR. Número de pieza: PQS500221 Aplicaciones: LAND RANGE ROVER Range Rover 2002-2009 LR3 descubrimiento 3 2005-2009 LAND RANGE ROVER Range Rover deporte 2005-2009 Más detalles: PQS500221 NUEVA correa secundaria de automóvil para LAND RANGE ROVER LR3 Discovery 3 2005-2009 Range Rover 2002-2009, Range Rover Sport 2005-2009 suministro de correa automática con calidad SUPERIOR Nombre de la marca: RALUX Origen: CN(Origen) Tipo: cinturón de coche El radio de la raíz: 3 cm. Ubicación de la línea de lanzamiento: no Personalizado: sí Ancho de banda: 12 CM Paso: no Punta Del Diente: no País/región de fabricación de automóviles: Shanghai, China Resistencia al calor: alta Ángulo del perfil: no Tipo de material: caucho Número de pieza de intercambio: PQS500221 Altura del engranaje: 3 cm Altura del cinturón: 3 cm Características especiales: transmisión Ancho en la raíz del diente: 3 cm Otro número de pieza: PQS500221 Velocidad lineal: lejos Textura del material: caucho Número de pieza del fabricante: PQS500221 Estado: Nuevo Posición: polea Tipo: cinturón de coche Observación: Secundario, 4.4L, Gasolina, V8

Victorious Automotive · Toyota LC250 · Interior Protection Wireless Charger Silicone Protection Pad – Toyota Land Cruiser 250 (LC250) 2024 A precision-cut silicone pad that protects your LC250's centre console wireless charging surface from scratches, rattles and everyday wear — drop it in, done. LC250 2024 Land Cruiser 250 Silicone Centre Console Wireless Charging Anti-Rattle Black No Adhesive Easy Clean Overview The 2024 Toyota Land Cruiser 250 is one of the most anticipated vehicles of the decade — a return to rugged, go-anywhere capability paired with a genuinely premium interior. The LC250's centre console is a key part of that interior experience, and the built-in wireless charging pad is one of its most used daily touchpoints. Keeping that area looking pristine from day one is exactly what this silicone protection pad is designed to do. Engineered specifically for the LC250's charging recess, this silicone pad sits flush within the console, creating a soft, grippy surface that prevents your phone from sliding around while charging. The raised silicone construction absorbs vibration, effectively eliminating that frustrating rattling noise that a glass-backed phone can produce against a hard plastic surface during driving on uneven terrain — something LC250 owners will encounter often. Unlike adhesive-backed alternatives, this pad requires zero installation effort and leaves absolutely no residue. When it needs cleaning — whether from dust, grit from a trail run, or everyday debris — simply lift it out, rinse it, and drop it back in. It's the kind of thoughtful, low-effort accessory that makes owning a premium 4x4 feel properly finished. What's Included 🟫 Silicone Protection Pad × 1 Precision-fit for the LC250 wireless charging recess 📋 Fitment Reference Confirmed for Toyota Land Cruiser 250 (2024) Product Highlights Precision-cut to fit the LC250 centre console wireless charging recess exactly Soft silicone surface grips your phone and prevents movement while charging Eliminates rattling and tapping noises caused by phone vibration during driving Protects the original OEM surface from scratches, scuffs and daily wear No adhesive, no tools, no modifications — simply place and use Removable and fully washable — lifts out in seconds for easy cleaning Compatible with all Qi wireless charging-enabled smartphones Finished in stealth black to match the LC250's dark interior trim palette Durable silicone material maintains its shape and grip over time Maintains full wireless charging functionality — no signal interference Compatibility Vehicle Model Code Year Range Fitment Toyota Land Cruiser 250 (Prado) LC250 2024+ Direct Fit Toyota Land Cruiser 300 LC300 2021+ Not Compatible Toyota Land Cruiser 200 LC200 2008–2021 Not Compatible Toyota Land Cruiser Prado 150 J150 2009–2023 Not Compatible Installation Notes Difficulty: Effortless  ·  Time: Under 1 minute  ·  Tools Required: None Open the centre console area on your 2024 Land Cruiser 250 and locate the wireless charging recess. Ensure the OEM charging surface is clean and free from dust or debris before fitting. Place the silicone pad flat into the wireless charging recess, aligning it to the edges of the recess. Press lightly to seat the pad — it should sit flush with no lifting at the corners. Place your phone on the pad as normal to confirm wireless charging continues to function correctly. Note: Ensure no large debris or particles are trapped beneath the pad before fitting, as this may cause uneven seating. If the pad lifts at any corner, remove it, clean the recess, and refit. Some very thick phone cases may reduce wireless charging efficiency — test with your specific device. Built for Owners Who Care The LC250 deserves accessories that match its quality. This silicone pad is one of those small upgrades that you'll notice every single day — and wonder how you drove without it. Worldwide shipping available via DHL, FedEx, UPS and TNT. Shop All LC250 Interior Accessories Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 🔄 30-Day money-back guarantee ✈️ Worldwide shipping via DHL, FedEx, UPS & TNT 📞 +44 203 943 9919 Mon–Fri, 9am–7pm Victorious Automotive is an independent aftermarket accessory retailer. This product is not manufactured by, affiliated with, endorsed by, or approved by Toyota Motor Corporation or any of its subsidiaries. All vehicle names, model codes and trademarks are the property of their respective owners and are referenced solely for fitment identification purposes.

Victorious Automotive · Toyota Land Cruiser LC250 · Exterior Styling Prado 1958 Exterior Body Colour Side Stickers — 2024–2025 Toyota Land Cruiser 250 Precision-cut adhesive vinyl side stickers styled after the iconic 1958 Prado heritage design — a subtle yet striking exterior upgrade purpose-built for the LC250. LC250 2024–2025 Adhesive Vinyl Body Colour Match 3 Style Options Direct Fit Exterior Styling 1958 Prado Heritage Overview The 2024–2025 Toyota Land Cruiser 250 is one of the most anticipated 4x4 launches in years — a vehicle that bridges genuine off-road capability with refined, modern design. For owners who want to push the exterior aesthetic one step further, the body panel architecture of the LC250 provides an ideal canvas for purposeful exterior detailing. These Prado 1958 Heritage Side Stickers are designed to reference the original Land Cruiser's visual lineage — a nod to the model's storied 1958 origins rendered in contemporary adhesive vinyl. Available in three distinct layout styles (A, B, and C), each option applies directly to the lower body side panels, creating a clean graphic stripe that complements the LC250's bold shoulder lines without overwhelming them. Manufactured from premium-grade adhesive vinyl, these stickers are built to endure exposure to the elements — UV-resistant, weatherproof, and contoured for flush application to the LC250's panel surfaces. Whether you're building a lifestyle-focused daily driver or a heritage-inspired expedition rig, this is the kind of detail that separates a standard LC250 from one that's been thoughtfully personalised. What's Included 🎨 Body Colour Side Sticker Set Full set for both sides of the vehicle 🅰️ Style Option: A, B or C Select your preferred layout at checkout 📋 Application Guide Step-by-step instructions included 🔖 Backing Liner Pre-applied adhesive backing for clean installation Product Highlights Custom designed and cut specifically for the 2024–2025 LC250 body profile Heritage 1958 Prado graphic styling — a meaningful design reference for enthusiasts Three distinct layout styles (A, B, C) for personalised fitment High-quality adhesive vinyl construction — durable and long-lasting UV-resistant finish to prevent fading in direct sunlight Weatherproof and water-resistant — suitable for all climates Body-colour toned design integrates naturally with the LC250's lines No drilling, cutting, or professional installation required Residue-free removal if repositioning is needed during application Adds genuine visual character without permanent modification Compatibility Vehicle Year Range Trim / Grade Fitment Toyota Land Cruiser 250 (LC250) 2024–2025 All Grades Direct Fit Toyota Land Cruiser 300 (LC300) 2021–2025 All Grades Not Compatible Toyota Land Cruiser 200 (LC200) 2008–2021 All Grades Not Compatible Toyota Prado 150 Series 2009–2023 All Grades Not Compatible Toyota Hilux / 4Runner Any All Not Compatible Installation Notes Difficulty: Easy  ·  Estimated Time: 30–60 Minutes  ·  Tools Required: None Thoroughly clean the target panel area with a mild detergent and water solution. Remove any wax, grease, or residue. Allow to dry completely before proceeding. Dry-fit the sticker against the panel to confirm positioning and alignment. Use masking tape as a hinge line if working alone. Lightly mist the panel surface with a soapy water solution (a few drops of dish soap in a spray bottle). This allows repositioning during placement. Peel back the adhesive backing liner gradually, pressing the sticker onto the panel from the centre outward to prevent air bubbles. Use a soft squeegee or credit card to smooth the surface firmly, working from centre to edges. Allow the adhesive to cure for a minimum of 24 hours before washing the vehicle or exposing the area to heavy rain. ⚠ Note: Do not apply in direct sunlight or to a hot panel surface — this can reduce adhesive effectiveness. For best results, apply in a shaded environment at ambient temperature between 10°C and 30°C. The product includes a logo graphic element; refer to product images or contact our team if you have questions about placement. Complete Your LC250 Build Explore our full range of exterior and interior upgrades purpose-selected for the Toyota Land Cruiser LC250 — from body styling to protection accessories. Shop All LC250 Accessories Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 🚚 Worldwide Shipping via DHL, FedEx & UPS ↩ 30-Day Money-Back Guarantee 📞 +44 203 943 9919 Mon–Fri 9am–7pm Victorious Automotive is an independent aftermarket accessory retailer. This product is not manufactured by, affiliated with, or endorsed by Toyota Motor Corporation or any of its subsidiaries. All vehicle names, model codes, and trademarks referenced are used solely for fitment identification purposes. Product images are for illustrative purposes only — always verify compatibility with your specific vehicle specification before purchasing.