Victorious · Cooling System · Repair Kits
Coolant Water Pipe Repair Kit – LR049990
OEM-specification replacement for Range Rover, Range Rover Sport, Discovery, and Velar cooling systems. Copper and rubber construction ensures durability and thermal reliability.
LR049990
2010–2022
Copper & Rubber
Engine Cooling
Direct Fit
Multiple Vehicles
Overview
The coolant water pipe assembly is a critical component in the engine cooling circuit of modern Range Rovers, Range Rover Sports, Discoveries, and Velars. Over time, rubber gaskets and seals degrade under thermal stress, leading to coolant leaks, overheating, and potential engine damage. This comprehensive repair kit addresses those wear points with OEM-specification copper and rubber parts, restoring coolant integrity without requiring a full system replacement.
Built to factory standards, this kit is engineered for the 5.0L V8 engines in Range Rover (2010–2012) and Range Rover Sport (2014–), as well as the 3.0L V6 petrol engines found in Discovery 4 (LR4), all-new Discovery (2017–), and Range Rover Velar (2017–). The premium copper components resist corrosion and maintain compatibility with all coolant types, while the reinforced rubber ensures a lasting seal under sustained heat and pressure.
Professional installation is recommended, though the modular design allows for staged replacement of individual components if needed. A complete restoration kit—available in single, 5-pack, or 10-pack quantities—makes this ideal for workshop environments or fleets requiring preventive cooling system overhauls.
What's Included
🔧
Main Pipe Assembly
Copper construction with reinforced threads and fittings
⭕
Rubber Gaskets & Seals
Heat-resistant compound rated for 130°C+ operation
📋
Installation Guide
Clear diagrams and torque specifications included
✓
12-Month Warranty
Full replacement coverage on manufacturing defects
Key Highlights
- OEM Part Number LR049990 – direct replacement for factory-spec cooling systems
- Copper and premium rubber construction resists corrosion and thermal degradation
- Compatible with all OEM and approved aftermarket coolants
- Temperature rated to 130°C; maintains seal integrity under sustained load
- Modular design allows component-by-component installation or full-system overhaul
- Fits Range Rover L405 (2010–2012) with 5.0L V8 petrol
- Fits Range Rover Sport L494 (2014–) with 5.0L V8 petrol
- Fits Discovery 4 LR4 (2010–) and all-new Discovery (2017–) with compatible engines
- Fits Range Rover Velar (2017–2022) with 3.0L V6 petrol
- Available in single unit, 5-pack, or 10-pack quantities for fleet maintenance
Compatibility Chart
| Vehicle Model |
Years |
Engine |
Fit |
| Range Rover Vogue L405 |
2010–2012 |
5.0L V8 Petrol |
Direct Fit |
| Range Rover Sport L494 |
2014–2021 |
5.0L V8 Petrol |
Direct Fit |
| Discovery 4 LR4 |
2010–2016 |
3.0L V6 Petrol |
Direct Fit |
| Discovery (All-New) |
2017–2022 |
3.0L V6 Petrol |
Direct Fit |
| Range Rover Velar |
2017–2022 |
3.0L V6 Petrol |
Direct Fit |
| Range Rover Diesel Models |
All Years |
Diesel Engines |
Not Compatible |
Installation Guide
Difficulty Level: Intermediate | Time: 1–2 hours
- Disconnect the negative battery terminal and allow the engine to cool completely.
- Locate the coolant water pipe assembly beneath the inlet manifold (upper driver's side on V8 engines; center intake area on V6 engines).
- Unbolt the old pipe assembly using a 10mm socket and secure the engine block with a jack and wood block if needed for access.
- Remove all old gaskets and rubber seals; use a gasket scraper to clean the mating surfaces down to bare metal.
- Inspect the new copper pipe for any manufacturing burrs; smooth with fine emery cloth if present.
- Install new rubber gaskets on both ends, then slide the copper pipe into place, aligning all threaded holes.
- Reinstall bolts in a star pattern, tightening to 24 Nm (18 ft-lb) on V8 engines and 20 Nm (15 ft-lb) on V6 engines.
- Top up coolant reservoir with OEM-approved coolant and bleed the system at the highest bleed screw (typically on the thermostat housing).
- Run the engine at idle for 10 minutes, then check all connection points for weeps under load.
- Allow the engine to cool, then top up coolant level once more before road testing.
⚠ Important: Never open the coolant system on a hot engine. Always drain and dispose of coolant responsibly at an approved recycling facility. Check your vehicle's service manual for exact torque settings and bleed screw locations, as these vary by engine type.
Get Your Cooling System Back to Factory Spec
Coolant leaks don't resolve themselves—they escalate into overheating, head gasket failure, and expensive engine repairs. Order this OEM-specification repair kit now and restore your Range Rover, Discovery, or Velar to reliable, leak-free operation.
Shop Now
Use code 22GET20 for 20% off any 2 items
✓ 30-Day Money-Back Guarantee
✓ 12-Month Warranty
✓ Worldwide DHL Shipping
✓ 4.9★ — 12,300+ Reviews
✓ UK Support: +44 203 943 9919
Victorious Automotive is an independent aftermarket retailer. We are not affiliated with Land Rover, Range Rover, Jaguar Land Rover, or any OEM manufacturer. All product names, logos, and trademarks are the property of their respective owners. This product is designed to meet or exceed OEM specifications and is compatible with the listed vehicles; fitment responsibility rests with the end user or installer. Always verify compatibility with your vehicle's VIN or service manual before purchase.
