Range Rover Sport L494 MY13-20 Accessories

Victorious Automotive · Range Rover Sport L494 · Exterior Styling Carbon Fibre Roof Light Pod with LED Lights — Range Rover Sport L494 (2014–2021) A handcrafted real carbon fibre roof pod with super-bright integrated LED lighting — engineered for a clean, non-destructive install that preserves every original switch and gauge on your Sport. Range Rover Sport L494 2014–2021 Real Carbon Fibre LED Roof Pod Wireless Remote Non-Destructive Fit Fuse Box Powered Aerodynamic Design Handcrafted Overview The Range Rover Sport L494 is a vehicle built around presence — commanding on the road, refined within the cabin, and unmistakable from any angle. For owners who want to push that presence further without compromising the factory aesthetic, the roof line remains one of the most underutilised styling opportunities on the platform. This carbon fibre roof light pod changes that entirely. Crafted from genuine woven carbon fibre and finished with a precision gloss coat, this roof pod is designed specifically for the Range Rover Sport 2014–2021. Its aerodynamic profile sits flush and purposeful on the roofline — reminiscent of the kind of accessory you'd expect to see on a factory SVR special edition. Integrated high-spec LED lights deliver a super-bright, even output that draws eyes day or night, whether parked on the street or moving through traffic. What separates this pod from lesser alternatives is the installation philosophy. There's no drilling, no permanent modification, and no interference with the Sport's OBD, infotainment, or switch panel. Power draws cleanly from the fuse box, and the lights are operated via a wireless remote control — leaving your factory switches, gauges, and interior trim completely untouched. It's a modification that looks like it was always meant to be there. What's Included 🪨 Carbon Fibre Roof Pod Handcrafted real carbon fibre shell with gloss finish 💡 Integrated LED Light Bar High-spec super-bright LEDs pre-fitted to pod housing 📡 Wireless Remote Control Operates the LED lights independently of factory switches 🔌 Wiring Loom Pre-terminated for direct fuse box connection — no error codes 🧲 Automotive 3M Mounting Tape Heavy-duty adhesive for secure non-destructive roof fitment 📋 Installation Guide Step-by-step fitting instructions included Product Highlights Genuine woven carbon fibre construction — not plastic wrap or vinyl Precision gloss coat finish that complements factory bodywork Super-bright high-spec LED lights integrated into pod housing Wireless remote operation — zero factory switch interference Fuse box powered — clean, direct draw with no dashboard errors Non-destructive installation — no drilling, no permanent modifications Aerodynamic low-profile form designed for Sport L494 roofline Handcrafted one at a time — individually finished to high standard Fits all L494 Sport variants across the full 2014–2021 model run Retains 100% factory interior and exterior OEM appearance Compatibility Vehicle Code Years Fit Range Rover Sport SE L494 2014–2021 Direct Fit Range Rover Sport HSE L494 2014–2021 Direct Fit Range Rover Sport HSE Dynamic L494 2014–2021 Direct Fit Range Rover Sport SVR L494 2014–2021 Direct Fit Range Rover Sport Autobiography L494 2014–2021 Direct Fit Range Rover Sport (New Gen) L461 2022–2026 Not Compatible Range Rover Vogue L405 / L460 All Years Not Compatible Range Rover Velar L560 All Years Not Compatible Defender L663 All Years Not Compatible Installation Notes Difficulty: Intermediate  ·  Estimated Time: 1–3 Hours Thoroughly clean the roof mounting area using an isopropyl alcohol wipe to ensure the surface is completely free of wax, grease, or dirt residue. Dry-fit the roof pod to confirm positioning and alignment before committing to the adhesive — mark reference points lightly with masking tape if needed. Apply the included automotive 3M double-sided tape to the underside of the pod, then press firmly into position on the roof and hold for 60 seconds. Route the wiring loom discreetly through the roof seal and into the cabin — this typically follows the A-pillar trim channel without requiring permanent trim removal. Connect the wiring loom to an appropriate fuse in the fuse box — refer to your vehicle's fuse diagram for a suitable auxiliary circuit. Pair the wireless remote receiver to the LED system following the instructions included in the guide. Test the LED function across all modes using the remote before refitting any trim panels you may have temporarily displaced. ⚠ Please Note: The roof pod itself can be mounted by most owners with basic DIY confidence. However, the electrical wiring requires competence with automotive electrics. If you are unsure, we recommend having the wiring completed by a qualified auto-electrician. Installation is the responsibility of the customer. This product is handmade from real carbon fibre — minor surface variations are a natural characteristic of the material and not considered defects. Upgrade Your Range Rover Sport Today Shop the full Range Rover Sport L494 collection at Victorious Automotive — premium accessories for owners who refuse to settle for standard. Shop Range Rover Sport L494 Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ reviews 🚚 Worldwide Shipping via DHL, FedEx & UPS 🔁 30-Day Money-Back Guarantee 📞 +44 203 943 9919 Mon–Fri, 9am–7pm Victorious Automotive is an independent aftermarket accessories retailer. We are not affiliated with, endorsed by, or connected to Land Rover, Range Rover, Jaguar Land Rover (JLR), or any of their subsidiaries. All vehicle names, model codes, and trademarks are the property of their respective owners and are used for fitment reference purposes only.

Victorious Automotive · Range Rover Sport L494 · Tail Lights Smoked LED Rear Tail Light Assembly – Range Rover Sport L494 (2014–2020) Facelift Style A smoked, 2018 facelift-style LED tail light upgrade that transforms the rear presence of your L494 Sport — sold as a direct-fit pair with no modification required. L494 2014–2020 Smoked Finish Full LED Facelift Style ABS + PC Sold as Pair 12V Aftermarket Direct Fit Overview The Range Rover Sport L494 is one of the most visually commanding SUVs on the road — and the rear light signature plays a defining role in that presence. Whether you're running a pre-facelift 2014–2017 Sport or a later model looking to refresh the aesthetic, these smoked LED tail lights deliver an instantly recognisable upgrade without compromising function. Styled to replicate the refined 2018 facelift rear light design, these units combine a blacked-out smoked lens with a full LED light cluster — bringing a darker, more purposeful look to the Sport's rear end. The ABS and polycarbonate construction ensures durability in all conditions, while the 12V LED technology guarantees crisp, bright output for indicators, brake lights, and running lights alike. For pre-facelift L494 owners (2014–2017), this is one of the most impactful visual upgrades available — effectively bringing your Sport's rear styling in line with the 2018+ facelift specification. For 2018–2020 models, these units serve as a direct-fit, smoked-lens alternative to the OE units. Both left and right units are included, with precision-fit housings designed around the original mounting points. What's Included 💡 Left Tail Light Unit Driver side — smoked LED assembly 💡 Right Tail Light Unit Passenger side — smoked LED assembly 🔌 Wiring Connectors OE-matching plug connectors pre-fitted 🔩 Mounting Hardware Fixings compatible with OE apertures Product Highlights 2018 facelift-style LED design for all L494 model years Smoked blacked-out lens for a stealth, aggressive rear aesthetic Full LED cluster — running, brake, and indicator functions Sold as a matched pair — left and right included ABS + polycarbonate construction for long-term durability Precision moulded to OE mounting points — no drilling required 12V compatible — plug-and-play with factory wiring harness CCC externally tested and certified Direct upgrade for pre-facelift 2014–2017 L494 models Aftermarket replacement option for 2018–2020 L494 models Compatibility Vehicle Model Code Year Range Fit Type Notes Range Rover Sport L494 2014–2017 Direct Fit Tuning upgrade to 2018 facelift style Range Rover Sport L494 2018–2020 Direct Fit OE replacement with smoked finish Range Rover Sport L461 2022–2026 Not Compatible Different platform and rear architecture Range Rover Vogue L405 2013–2021 Not Compatible Different vehicle model Range Rover Vogue L460 2022–2026 Not Compatible Different vehicle model Defender L663 2020–2026 Not Compatible Different vehicle model Installation Notes Difficulty: Beginner–Intermediate  |  Estimated Time: 30–60 Minutes  |  Tools Required: Basic Hand Tools Open the tailgate and locate the access panel or trim covering the tail light mounting area on each side. Remove the retaining nuts or bolts securing the original tail light unit — typically 2–3 fixings per side. Carefully pull the OE tail light assembly away from the body, taking care not to stress the wiring loom. Disconnect the OE wiring connector from the back of the original unit — note the orientation before removal. Connect the new smoked LED tail light unit to the factory wiring connector — it should click securely into place. Position the new unit against the body, aligning with the OE mounting points, and secure with the original fixings. Repeat for the opposite side, then test all light functions — running, brake, and indicator — before reassembling trim panels. Important: Always disconnect the vehicle battery before working with electrical components. If your vehicle is under warranty, consult your dealership before making modifications. Some 2014–2017 pre-facelift vehicles may require a resistor or coding adaptation to prevent indicator hyper-flash — test all functions before finalising installation. Upgrade Your L494 Sport's Rear Signature These smoked LED tail lights are one of the most impactful visual modifications available for the Range Rover Sport L494 — bringing facelift aesthetics and a darker, more purposeful stance to any model year. Explore more Sport L494 accessories at Victorious. Shop Range Rover Sport L494 → Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 📦 Worldwide Shipping via DHL, FedEx, UPS & TNT ↩️ 30-Day Money-Back Guarantee 📞 +44 203 943 9919 Mon–Fri, 9am–7pm Victorious Automotive is an independent aftermarket accessory retailer. We are not affiliated with, endorsed by, or in any way connected to Land Rover, Jaguar Land Rover (JLR), or any of their subsidiaries. All vehicle names, model codes, and trademarks referenced are used for fitment identification purposes only and remain the property of their respective owners. This product is an aftermarket part and is not manufactured by or sourced from JLR.

Victorious Automotive · Range Rover Sport L494 · Lighting Aftermarket LED Rear Tail Light Assembly for Range Rover Sport L494 (2014–2020) — 2018 Facelift Style A direct-fit LED tail light upgrade that brings the sharper, more contemporary lighting signature of the post-facelift Sport to pre-facelift models — without modification. Range Rover Sport L494 2014–2020 LED Lighting ABS + PC 12V Facelift Style Direct Fit Pair Included CCC Certified LR116468 / LR116471 Overview The Range Rover Sport L494 remains one of Land Rover's most compelling performance SUVs — a vehicle that balances genuine off-road capability with a presence on the road that few rivals can match. Whether you're running a pre-facelift 2014–2017 model or the refreshed 2018–2020 version, the rear end is central to how the Sport is perceived from behind. These aftermarket LED tail light assemblies are engineered to the proportions and mounting points of the L494 platform, offering a direct replacement or a stylistic upgrade to the 2018 facelift LED light signature. The result is a cleaner, more modern rear graphic — with no cutting, no rewiring, and no compromises to build quality. Constructed from impact-resistant ABS and optically clear polycarbonate, they're built to endure the same conditions your Sport handles every day. For owners looking to modernise the rear aesthetic of an early L494, or simply replace a damaged unit with something that performs and looks better than the original fitment, these lights represent a considered, high-value upgrade. Full LED operation means faster illumination response and longer service life compared to conventional halogen units — two qualities that matter whether you're on a motorway or a mountain pass. What's Included 🔴 Left LED Tail Light Driver-side assembly — LR116468 🔴 Right LED Tail Light Passenger-side assembly — LR116471 🔩 Mounting Hardware All necessary fixings for installation 📄 Installation Guide Basic fitting reference document Product Highlights Direct-fit replacement for Range Rover Sport L494 (2014–2020) — no modification required Emulates the 2018 facelift LED rear light signature for a modernised appearance Full LED construction across all functions — brake, tail, indicator, reverse Faster illumination response versus halogen for improved road safety ABS + polycarbonate construction resists impact, UV degradation and weathering 12V direct operation — plug-and-play with standard L494 wiring looms CCC certified — meets required electrical and safety standards Supplied as a matched pair — left and right included in every order Part references LR116468 (left) and LR116471 (right) for easy cross-referencing Lightweight at 3kg total — no impact on vehicle dynamics or boot access Compatibility Model Code Year Range Trim / Notes Fitment Range Rover Sport L494 2014–2017 Pre-facelift — upgrade to facelift style Direct Fit Range Rover Sport L494 2018–2020 Facelift — like-for-like replacement Direct Fit Range Rover Sport L461 2022–2026 New generation platform — different architecture Not Compatible Range Rover Vogue L405 2013–2021 Different body and mounting points Not Compatible Range Rover Velar L560 2017–2023 Distinct rear light architecture Not Compatible Defender L663 2020–2026 Entirely different platform and format Not Compatible Installation Notes Difficulty: Moderate  ·  Estimated Time: 45–75 minutes  ·  Tools: Standard trim tools, T20 Torx driver Open the boot and locate the interior trim panel behind each tail light cluster — carefully remove it using a trim pry tool to avoid damaging the lining. Disconnect the factory wiring connector from the existing tail light assembly by pressing the release tab and pulling the plug clear. Remove the retaining nuts (typically T20 Torx) securing the light unit to the body — there are usually three or four per side. Carefully withdraw the original light assembly from the rear of the vehicle, taking care not to scratch the surrounding bodywork. Align the new LED tail light unit with the mounting studs, ensuring the weatherstrip seal sits flush against the body panel before tightening. Reconnect the wiring loom connector until it clicks firmly into place, then refit the interior trim panel. Before closing the boot, test all functions — brake, tail, indicator, and reverse — to confirm full operation on both sides. ⚠ Important: If your vehicle displays a bulb failure warning after installation, this may be due to the lower current draw of LED units versus the original halogen lamps. A load resistor or LED-compatible flasher relay may be required to resolve this. Professional installation is recommended if you are unfamiliar with automotive electrical systems. Upgrade Your Sport's Rear End The right lighting upgrade changes how your Range Rover Sport is perceived — day and night. Browse the full L494 accessory range or get in touch with our team if you have compatibility questions. Shop Range Rover Sport L494 → Use code 22GET20 for 20% off when you buy any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 📦 Worldwide Shipping via DHL, FedEx, UPS & TNT ↩ 30-Day Money-Back Guarantee 📞 +44 203 943 9919 Mon–Fri, 9am–7pm Victorious Automotive is an independent aftermarket accessory retailer. We are not affiliated with, authorised by, or in any way connected to Land Rover, Jaguar Land Rover (JLR), or any of their subsidiaries. All vehicle names, model codes, and part numbers referenced on this page are used solely for compatibility identification purposes. This product is an aftermarket part and is not a genuine Land Rover OEM component.

Victorious Automotive · Range Rover · Interior Lighting Range Rover Additional Ambient Lighting Upgrade — Fiber Optic Door Panel Illumination Transform your Range Rover's interior atmosphere with precision-engineered fiber optic band lighting that wraps your door panels in a seamless, continuous glow — no harsh spots, no EL strips, just genuine ambient refinement. RR Classic MK1 P38A MK2 L322 MK3 L405 MK4 RR Sport 1970–2016+ Fiber Optic Door Panel Lighting Interior Atmosphere Direct Fit Not EL Light Overview The Range Rover has always set the benchmark for luxury SUV interiors — commanding, refined, and unmistakably premium. Whether you're driving a classic MK1, the iconic P38A, the sophisticated L322, a contemporary L405, or an RR Sport, the interior deserves lighting that matches the vehicle's standing. Factory ambient lighting, where fitted, is often limited in coverage and colour consistency — leaving door panels under-lit and the overall atmosphere short of what these vehicles are capable of. This fiber optic band ambient lighting kit fills that gap with precision. Unlike EL (electroluminescent) strips that can produce uneven glow and degrade quickly, genuine fiber optic bands distribute light uniformly and continuously along their entire length — no hot spots, no visible light sources, just a clean, elegant line of illumination that follows the contours of your door panel. Each of the four 1-metre bands comes paired with its own dedicated light source, making installation flexible and the end result consistent across all four doors. Fitting is straightforward for anyone comfortable removing door panel trim — the bands are routed behind the existing panel architecture and connected to a suitable 12V source. The result is a measurable step up in perceived interior quality: the kind of subtle, well-considered upgrade that Range Rover enthusiasts will appreciate immediately and notice every time they open a door after dark. What's Included 💡 4× Fiber Optic Bands 1 metre each — one per door panel 🔦 4× Dedicated Light Sources Individual unit per band for consistent output 📋 Installation Instructions Step-by-step fitting guide included Product Highlights Genuine fiber optic technology — not EL strip lighting Uniform, continuous glow along the full 1m band length Four individual light sources for consistent door-to-door output Covers all four door panels in a single kit Subtle, premium atmosphere — not garish or overloud Compatible with multiple Range Rover generations spanning 1970–present No visible hotspots or light source bleed-through Flexible band design routes easily behind door card trim Connects to standard 12V vehicle power — no specialist wiring Reversible installation — no permanent modification to factory trim Compatibility Model Generation / Code Years Fitment Range Rover Classic MK1 1970–1996 Direct Fit Range Rover P38A MK2 1994–2002 Direct Fit Range Rover L322 MK3 2002–2012 Direct Fit Range Rover Vogue L405 MK4 2012–2021 Direct Fit Range Rover Sport L320 / L494 2005–2022 Direct Fit Range Rover Sport L461 2022–2026 Verify Before Purchase Range Rover Vogue L460 2022–2026 Verify Before Purchase Range Rover Velar L560 2017–2024 Verify Before Purchase Installation Notes Difficulty: Moderate  ·  Estimated Time: 1.5–3 Hours  ·  Tools Required: Trim removal tools, panel clips, 12V power tap Remove each door card carefully using appropriate trim clips and plastic pry tools — avoid metal tools directly on the panel to prevent marking. Plan your routing path for each fiber optic band along the lower or mid-section of the door panel interior, following the natural contour lines of the trim. Position each light source unit in a concealed location within the door void — behind the armrest pocket or lower panel area works well on most Range Rover generations. Secure the fiber optic band along its intended route using the supplied adhesive or trim-safe tape, ensuring it lies flat and taut without kinks. Connect each light source to a suitable switched 12V feed — the interior door lamp circuit is the most commonly used tap point for a clean, ignition-controlled result. Refit the door card, test each panel before fully re-clipping, and adjust band positioning if any light bleed is visible at the panel edges. Repeat for all four doors, confirming consistent output and colour balance across the full set before completing the final fitment. ⚠ Note: Always disconnect the vehicle battery before accessing door wiring on vehicles with airbag-equipped door panels. On newer variants (L405, L494 and above), consult your vehicle's wiring diagram before tapping any low-current circuits. If in doubt, have a qualified auto electrician complete the connection work. Elevate Your Interior. Every Journey. Ambient lighting is one of the most impactful — and most underrated — interior upgrades available to Range Rover owners. This fiber optic kit delivers a factory-quality result at a fraction of the cost of a dealer-fitted solution. Browse our full Range Rover interior collection or speak with our team on +44 203 943 9919 (Mon–Fri, 9am–7pm) if you'd like guidance on compatibility for your specific model year. Shop Range Rover Interior Upgrades Use code 22GET20 for 20% off when you buy any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 🚚 Worldwide Shipping via DHL, FedEx, UPS & TNT ↩ 30-Day Money-Back Guarantee 📞 Expert Support Mon–Fri 9am–7pm Victorious Automotive is an independent aftermarket accessory retailer. This product is not manufactured by, endorsed by, or affiliated with Jaguar Land Rover Limited, Land Rover, or any of their subsidiaries. All vehicle model names, codes, and trademarks referenced are used for fitment identification purposes only and remain the property of their respective owners.

Victorious Automotive · Range Rover & Discovery · Mirror Indicators LED Dynamic Turn Signal Blinker Side Mirror Indicators — Range Rover & Discovery L405 L494 L462 Upgrade your side mirror indicators to a smooth, sequential LED blink — a direct OEM-style replacement that installs in minutes with zero coding required. L405 2013–2018 L494 2014–2018 L462 2017–2018 Evoque L538 2012–2013 Discovery 4 LR4 2014–2016 Dynamic Scroll Effect Plug & Play E8 Approved Semi-Smoke Lens 100% Waterproof Error-Free Overview The Range Rover L405, Range Rover Sport L494, and Land Rover Discovery models are already vehicles that command attention — but the factory mirror indicators on many of these builds are uninspiring at best. For an owner who has invested in a prestige SUV, the details matter, and the side mirror turn signals are one of the few exterior elements that catch the eye of anyone watching you signal off a junction or change lanes. These LED Dynamic Turn Signal Mirror Indicators replace your existing side mirror repeaters with a flowing, sequential LED sweep that moves outward in a single smooth arc — the same dynamic blink pattern you'll find on flagship European performance vehicles. The semi-smoke lens integrates cleanly into the mirror housing without looking aftermarket, complementing both stock and upgraded mirror finishes. E8 road-legal certification means these are built to standard, not just aesthetics. What sets these apart from cheap eBay alternatives is the genuine plug-and-play wiring harness that connects directly to your existing factory plug — no splicing, no relay adaptation, and crucially, no dashboard warning lights or coding visits to your Land Rover dealer. Waterproof construction and long-life LED technology mean once fitted, these are set for the lifetime of the vehicle. What's Included 💡 Driver Side Indicator (Left) Dynamic LED scroll, semi-smoke lens 💡 Passenger Side Indicator (Right) Dynamic LED scroll, semi-smoke lens 🔌 Factory-Match Plug Harness Direct OEM connector, no modification needed 📋 Fitting Instructions Step-by-step installation guide included Product Highlights Dynamic sequential LED sweep for a premium blink effect Semi-smoke matte lens finish for a stealth, understated look E8 road-legal certification — compliant for UK & EU roads Plug-and-play wiring directly into OEM factory connector 100% error-free — no bulb fault warnings on your dashboard No coding or dealer visit required after fitting IP-rated waterproof construction — suitable for all weather Long-life LED technology — significantly outlasts halogen repeaters Sold as a pair — left and right included in every set Direct OEM replacement — no drilling, cutting, or modification Vehicle Compatibility Vehicle Code Years Fitment Range Rover Vogue L405 MK IV 2013–2018 Direct Fit Range Rover Sport L494 2014–2018 Direct Fit Land Rover Discovery 4 / LR4 L319 Facelift 2014–2016 Direct Fit Land Rover Discovery 5 L462 2017–2018 Direct Fit Range Rover Evoque L538 Pre-Facelift 2012–2013 Direct Fit Range Rover Evoque L538 Post-Facelift 2014–2019 Verify Before Purchase Range Rover Vogue L460 2022–2026 Not Compatible Range Rover Sport L461 2022–2026 Not Compatible Defender L663 2020–2026 Not Compatible Installation Notes Difficulty: Easy  ·  Estimated Time: 20–35 minutes  ·  Tools Required: Trim removal tool Carefully fold in your wing mirror and use a trim removal tool to gently unclip the existing mirror indicator lens from the housing. Apply light, even pressure to avoid cracking the surrounding trim. Disconnect the factory plug from the back of the existing indicator unit — it will unclip with a gentle squeeze of the connector tab. Connect the new LED dynamic indicator's plug directly into the factory socket. The connector is keyed, so it will only seat in one orientation. Clip the new indicator unit into the mirror housing until it seats flush. Test the function by cycling the ignition on and checking both left and right turn signals. Repeat for the opposite side. No software coding or dealer intervention is required — the units are 100% plug-and-play. Note: Colour appearance may vary slightly from product images depending on ambient lighting and screen calibration. Always confirm your exact vehicle model code and build year before purchasing — some early and late production variants within the same model year may differ in connector type. Upgrade Your Indicators. Elevate the Detail. Small changes make a significant impression. These dynamic LED mirror indicators are one of the easiest, most impactful exterior upgrades you can make to your Range Rover or Discovery — and they're backed by our 30-day money-back guarantee. Shop Range Rover Accessories Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 🚚 Worldwide shipping via DHL, FedEx & UPS ↩️ 30-day money-back guarantee 📞 +44 203 943 9919 Mon–Fri 9am–7pm Victorious Automotive is an independent aftermarket accessory retailer. We are not affiliated with, endorsed by, or connected to Land Rover, Range Rover, Jaguar Land Rover (JLR), or any of their subsidiaries. All vehicle names, model codes, and trademarks referenced are used for fitment identification purposes only and remain the property of their respective owners.

Victorious Automotive · Range Rover · Lighting Upgrades LED Strobe Warning Lights for Range Rover – Multi-Mode Flash DRL Daytime Running Light High-visibility 12V LED strobe daytime running lights engineered for Range Rover fitment — delivering sharp spot-beam output and multiple flash modes for enhanced presence on road or off. Range Rover MZORANGE 32874137501 12V LED Strobe Flash Multi-Mode 9cm Diameter Spot Beam CE Certified 0.2kg Plastic Housing Lens Included DRL / Warning Light Overview Range Rover models are built around commanding presence — whether navigating urban environments or tackling demanding terrain. Keeping your lighting setup sharp, functional, and visually distinctive is a natural extension of that philosophy. Whether you're running an L405 Vogue, an L494 Sport, or the newer L460 and L461 generation, aftermarket LED lighting upgrades remain one of the most impactful ways to personalise and enhance your vehicle's front-end character. These LED strobe warning lights from MZORANGE are compact, 12V-compatible units that function as both daytime running lights and attention-grabbing strobe flash units. Running on a robust LED light source with spot beam output, they deliver a focused, crisp illumination pattern suited to both visibility and aesthetics. The 9cm diameter housing keeps the fitment discreet while still delivering a punchy light output that reads clearly even in daylight conditions. With multiple flash modes built in — including steady DRL and strobe flasher options — these lights give Range Rover owners the flexibility to configure their front lighting setup to suit the situation. CE certified and weighing just 200g per unit, they're a lightweight, reliable addition that installs cleanly and performs consistently across a broad operating voltage range. What's Included 💡 LED Strobe Light Units Pair of 12V LED strobe/DRL lights, 9cm diameter 🔭 Protective Lens Pre-fitted lens included on each unit 🔌 Wiring Harness 12V connection leads for direct vehicle integration 🔩 Mounting Hardware Fixings for secure installation to bumper or grille area 📋 Installation Guide Basic fitting instructions included in packaging Product Highlights 12V direct compatibility with Range Rover electrical systems Multiple flash modes including steady DRL and strobe patterns Compact 9cm diameter — discreet fitment on bumper or grille LED spot beam output — sharp, focused and highly visible CE certified for quality and safety compliance Lightweight at just 200g per unit — no added front-end load Durable plastic housing built to resist vibration and road debris Lens included — no additional purchase required to complete install Functions as both a daytime running light and warning flasher Plug-in wiring design for a straightforward, clean installation Compatibility Model Code Years Fitment Range Rover Vogue L405 2013–2020 Direct Fit Range Rover Sport L494 2013–2020 Direct Fit Range Rover Velar L560 2018–2022 Direct Fit Range Rover Vogue L460 2022–2026 Direct Fit Range Rover Sport L461 2022–2026 Direct Fit Defender L663 2020–2026 Direct Fit Range Rover Evoque L551 2019–2024 Direct Fit Discovery Sport L550 2015–2024 Verify Before Purchase Freelander 2 L359 2006–2015 Not Recommended Installation Notes Difficulty: Moderate  ·  Estimated Time: 45–90 Minutes  ·  Tools Required: Yes Disconnect the vehicle battery negative terminal before beginning any electrical work to prevent accidental short circuits. Identify your preferred mounting location — typically within the front bumper valance, lower grille surround, or fog light recess area depending on your specific Range Rover model. If cutting or drilling is required, mark and measure carefully before proceeding. Use a step drill bit for clean, consistent apertures in plastic bumper sections. Feed the wiring harness through the bumper cavity to the engine bay, routing away from hot components and moving parts. Use existing grommets or add your own for cable protection. Connect the positive lead to a switched 12V source (ignition-on circuit recommended) and the negative lead to a clean chassis ground point. Seat the light units firmly into position and secure with the included mounting hardware. Ensure the lens is properly seated and the housing is flush. Reconnect the battery, power on the ignition, and test all flash modes before closing up the bumper assembly. ⚠ Important: Always verify your local road traffic regulations regarding strobe and flashing lights on public roads before use. In many regions, strobe/flashing white or amber lights on the front of a vehicle are restricted to emergency or off-road use only. Use of these lights on public highways may be subject to legal restrictions. Installation involving significant bumper modification should be undertaken by a qualified automotive technician. Upgrade Your Range Rover's Lighting Join over 12,300 verified Range Rover and Land Rover owners who trust Victorious Automotive for precision-matched accessories. Browse our full lighting collection for your specific model below. Shop Range Rover Accessories Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 🚚 Worldwide Shipping via DHL, FedEx, UPS & TNT ↩ 30-Day Money-Back Guarantee 📞 +44 203 943 9919 Mon–Fri, 9am–7pm Victorious Automotive is an independent aftermarket accessory retailer. We are not affiliated with, endorsed by, or connected to Jaguar Land Rover Limited, Land Rover, Range Rover, or any of their subsidiaries. All brand names, model names, and vehicle codes referenced on this page are used for compatibility identification purposes only. Always verify fitment against your specific vehicle's trim level and build specification before purchase. Road use of strobe and flashing lights may be subject to local legislation — the buyer is solely responsible for ensuring compliance with applicable laws.

Victorious Automotive · Range Rover Evoque · Interior Lighting Interior LED Light Kit for Range Rover Evoque – Full Cabin Upgrade (2005–2023) Transform every journey inside your Evoque with a precisely engineered LED interior kit — brighter, cleaner light across every cabin zone, with zero error codes and no rewiring required. Range Rover Evoque L538 · L551 2005–2023 Canbus Error Free Plug & Play 50,000hr Lifespan Heat Resistant Direct Fit Overview The Range Rover Evoque has always stood apart for its design-led interior — low roofline, premium surfaces and a cabin built to impress. But the factory halogen interior bulbs do very little to complement that effort. They cast a dim, warm-yellow light that dates the interior and leaves door pockets, boot areas and vanity mirrors barely usable in low-light conditions. This LED kit is the single most effective low-cost upgrade you can make to the Evoque's interior presence. Engineered specifically for Land Rover applications across the 2005–2023 model range, each bulb in this kit is fully Canbus-compatible — meaning your instrument cluster will not register a fault, and you will not encounter the blinking or flicker that cheaper universal LEDs are notorious for. The output is a clean, neutral-to-cool white that transforms the cabin feel from factory-standard to genuinely modern, without touching a single wire. Whether you drive an early L538 Evoque or the current L551 generation, this kit has been verified for direct fitment across all trim levels. Installation requires no professional expertise — the complete kit including a pry tool can be fitted in under 30 minutes at home, making this one of the most rewarding upgrades in the Victorious range. What's Included 💡 Front Map / Dome Light Model-specific LED bulb for front overhead reading and dome positions 💡 Rear Map / Dome Light Rear passenger overhead illumination — direct replacement bulb 🪞 Vanity Mirror Lights Available in select packages — sun visor mirror illumination 🗄️ Glove Box Light Available in select packages — interior glove compartment LED 📦 Trunk / Boot Light Available in select packages — load area LED replacement 🔧 Installation Pry Tool Trim-safe removal tool included to protect interior panels Product Highlights Super bright LED output for a noticeably improved cabin ambiance 100% Canbus error-free — no dashboard warnings or fault codes True plug-and-play fitment — no wiring, no modifications Up to 50,000 hours operational lifespan — essentially lifetime fit Heat-resistant construction for safe long-term cabin use Clean neutral-white light output matching modern premium interiors Energy efficient — draws significantly less power than OEM halogens Engineered specifically for Land Rover / Range Rover electrical systems Compatible with all trim levels across 2005–2023 model years Includes trim-safe pry tool — no additional tools required Compatibility Model Code Years Fitment Range Rover Evoque L538 2011–2018 Direct Fit Range Rover Evoque L551 2019–2023 Direct Fit Range Rover Sport L320 2005–2013 Direct Fit Range Rover Sport L494 2013–2020 Direct Fit Range Rover Vogue L405 2013–2020 Direct Fit Land Rover Freelander 2 L359 2006–2014 Direct Fit Land Rover Discovery 3 L319 2005–2009 Direct Fit Land Rover Discovery 4 L319 2009–2016 Direct Fit Land Rover Discovery 5 L462 2017–2023 Direct Fit Range Rover Vogue L460 2022–2026 Verify Before Order Range Rover Sport L461 2022–2026 Verify Before Order Not sure which variant fits your vehicle? Call us on +44 203 943 9919 Mon–Fri, 9am–7pm and we'll confirm your fitment before you order. Installation Guide 🔧 Difficulty: Easy  ·  Estimated Time: 20–30 Minutes  ·  Tools Required: Included Pry Tool Only Ensure all interior lights are switched off and the ignition is fully off before beginning. Allow any existing bulbs a few minutes to cool if the vehicle has been recently used. Using the included trim-safe pry tool, carefully lever open the lens cover on each light fitting — start at one edge and work around gently to avoid cracking the housing. Remove the existing halogen or incandescent bulb from its socket. Twist or pull depending on your specific fitting type — refer to your Evoque owner's manual if unsure of bulb type. Insert the corresponding LED replacement bulb from this kit. Ensure the pins seat fully into the socket. If LEDs do not illuminate after testing, rotate the bulb 180° — polarity is the most common cause of non-illumination. Snap the lens cover back into position. Turn on the interior lights and verify full illumination. Repeat across all zones included in your selected package. If a bulb feels loose, use a small flat tool to gently widen the metal pin clips inside the socket for a more secure grip. ⚠ Caution: Do not handle removed halogen bulbs immediately after use — they retain significant heat. Allow cooling before disposal. Do not apply excessive force when removing lens covers on the L551 Evoque as the housings use a clip-and-slot retention system that can crack under pressure. Shop by Your Evoque Browse the full accessory range curated specifically for your generation of Range Rover Evoque: 🔗 Evoque L538 (2011–2018) Full accessory collection for first-gen Evoque 🔗 Evoque L551 (2019–2023) Full accessory collection for second-gen Evoque Upgrade Your Evoque Interior Today Thousands of Land Rover and Range Rover owners across the UK and worldwide have transformed their cabins with this exact kit. Join them — and see the difference quality LED lighting makes from the first switch-on. Shop Evoque Accessories Use code 22GET20 — 20% off any 2 items ⭐ 4.9/5 Stars — 12,300+ Verified Reviews 📦 Worldwide Shipping — DHL, FedEx, UPS, TNT ↩ 30-Day Money-Back Guarantee 📞 +44 203 943 9919 Mon–Fri, 9am–7pm Victorious Automotive is an independent aftermarket accessory retailer. We are not affiliated with, endorsed by, or connected to Jaguar Land Rover Limited, Land Rover, Range Rover, or any of their subsidiaries. All brand names and model references are used for fitment identification purposes only. All trademarks remain the property of their respective owners.