Defender L663 Accessories

Victorious Automotive · Defender L663 · Interior Trim Carbon Fiber Central Console Panel Trim for Land Rover Defender 110 L663 (2020–2021) Real carbon fiber construction with a peel-and-stick fit — a clean, purposeful upgrade to one of the Defender's most visible interior touchpoints. Defender L663 2020–2021 Real Carbon Fiber 110 Wheelbase Central Console Trim Self-Adhesive Fit Interior Upgrade No Drilling Required Overview The 2020–2021 Land Rover Defender 110 L663 marked a defining moment in the Defender's history — a vehicle that balanced modern engineering with unmistakable character. The interior reflects that ambition, but for owners who want to push the cabin one step further, the central console area presents an obvious opportunity. It's a high-visibility zone, touched constantly and seen immediately by anyone who steps inside. This Real Carbon Fiber Central Console Panel Trim is designed specifically for the Defender 110 (2020–2021) interior layout, covering the console panel with precision-cut genuine carbon fiber that sits flush against the factory surface. The weave pattern is consistent and tightly finished, lending the kind of texture and depth that aftermarket plastic overlays simply cannot replicate. The result is a subtle but unmistakable elevation — one that reads as considered rather than accessorised. Installation requires no tools, no modification, and no permanent alteration to the vehicle. The trim arrives pre-backed with automotive-grade adhesive tape, the same category used across professional-fit interior applications. Clean the surface, peel the backing, and align carefully — the entire process takes minutes. For Defender owners who value the vehicle's integrity as much as its appearance, this is precisely the kind of upgrade worth making. What's Included 🪶 Carbon Fiber Console Trim 1 × real carbon fiber panel, pre-cut to fit 🔲 Pre-Applied Adhesive Tape Automotive-grade, factory-bonded to reverse side 📋 Installation Guide Step-by-step fitting instructions included Product Highlights Genuine real carbon fiber construction — not vinyl wrap or ABS plastic Consistent 2×2 twill weave pattern with high-gloss resin finish Precision-cut for exact fitment on Defender 110 L663 (2020–2021) Pre-applied automotive-grade 3M-style adhesive tape on reverse Tool-free, no-drill installation — completely reversible Lightweight material — adds zero meaningful weight to the cabin Resistant to heat, UV fading, and interior wear over time Colour-fast finish that won't yellow or peel under normal use Seamlessly integrates with factory Defender interior aesthetics Compatible with both standard and upgraded Defender 110 interior trims Compatibility Model Code Year Range Fit Land Rover Defender 110 L663 2020–2021 Direct Fit Land Rover Defender 90 L663 2020–2021 Verify Before Purchase Land Rover Defender 130 L663 2022–2026 Not Compatible Land Rover Defender 110 L663 2022–2026 Not Compatible Range Rover Sport L494 2013–2020 Not Compatible Range Rover Vogue L405 2013–2020 Not Compatible Installation Notes Difficulty: Easy  ·  Estimated Time: 10–20 Minutes  ·  Tools Required: None Park your Defender 110 in a clean, dry environment at room temperature. Cold or humid conditions can compromise adhesive bonding. Thoroughly clean the central console panel surface using an isopropyl alcohol wipe or equivalent. Remove all dust, grease, and residue and allow to dry completely. Test-fit the carbon fiber trim panel against the console surface without removing the adhesive backing. Confirm alignment and panel coverage before committing. Peel back a small section of the adhesive liner from one edge of the trim. Carefully align that edge with the console panel and press firmly into position. Slowly peel the remaining liner away while pressing the trim down progressively across its full length. Work from one edge to avoid air pockets. Apply firm, even pressure across the entire surface for 30–60 seconds. Pay particular attention to corners and edges to ensure full adhesion. Allow the adhesive to cure for a minimum of 24 hours before exposing the trim to direct heat, direct sunlight, or cleaning products. ⚠ Important: Do not attempt installation on a cold or freshly cleaned surface that has not fully dried. Adhesive performance is significantly reduced below 15°C (59°F). If the trim requires repositioning, work carefully to avoid stretching or creasing the carbon fiber panel. Complete Your Defender Interior This trim is one of the most immediate upgrades you can make to the Defender 110 cabin — real material, proper finish, zero compromise. Browse the full Defender L663 interior collection to find everything designed to the same standard. Shop Defender 110 (2020–2021) Collection Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 🔄 30-Day money-back guarantee 🌍 Worldwide shipping via DHL, FedEx, UPS & TNT 📞 Mon–Fri 9am–7pm · +44 203 943 9919 Victorious Automotive is an independent aftermarket accessories retailer. This product is not manufactured by, affiliated with, endorsed by, or approved by Land Rover, Jaguar Land Rover (JLR), or any of their subsidiaries. All vehicle names, model codes, and trademarks referenced are the property of their respective owners and are used solely for fitment identification purposes.

Victorious Automotive · Defender L663 · Interior Protection ABS Carbon Fiber Anti-Kick Tailgate Protection Panel Stickers — Land Rover Defender 110 (2020–2021) Precision-fit ABS carbon fiber trunk tailgate protection panels that guard your Defender 110's rear door from scuffs and kicks while adding a sharp, purposeful finish to the interior. Defender L663 2020–2021 ABS Carbon Fiber Anti-Kick Protection Tailgate Panel No-Drill Install Interior Trim Adhesive Fit Overview The Land Rover Defender 110 L663 reintroduced a legend for a new generation — blending rugged capability with a distinctly modern, purposeful interior. Every detail inside the Defender communicates intent, which makes the tailgate area — one of the most frequently used and most exposed surfaces in the cabin — worth protecting properly. These ABS carbon fiber anti-kick protection panels are designed specifically for the 2020–2021 Defender 110 trunk tailgate. Acting as a barrier against the everyday wear caused by loading, unloading, boots, and gear, they shield the factory trim from scratches, scuffs, and impact marks that accumulate over time. The carbon fiber texture finish integrates cleanly with the Defender's interior aesthetic without looking afterthought. Installation requires no drilling, no specialist tools, and no modification to the vehicle. Each panel arrives pre-cut to follow the exact profile of the Defender 110 tailgate and is backed with automotive-grade adhesive tape for a secure, residue-free bond. If you're particular about keeping your Defender's interior in the condition it deserves, this is a simple, effective upgrade. What's Included 🛡️ Carbon Fiber Tailgate Protection Panel 1× ABS carbon fiber anti-kick cover panel, pre-cut for Defender 110 trunk tailgate 🔧 Automotive Adhesive Tape Pre-applied 3M-style tape on the reverse for immediate, tool-free installation 📄 Installation Guide Step-by-step fitment instructions for a clean, bubble-free application Product Highlights Precision cut to fit the 2020–2021 Defender 110 trunk tailgate profile exactly ABS substrate with carbon fiber texture finish — lightweight yet impact-resistant Protects factory trim from kicks, scuffs, boot contact, and loading damage Sleek carbon fiber aesthetic complements the Defender's modern interior design Tool-free installation — no drilling, no cutting, no modifications required Automotive-grade adhesive backing ensures a strong, long-lasting bond Residue-free removal if repositioning is needed during installation UV-stable finish — will not fade, yellow, or crack over time Does not interfere with tailgate operation, hinges, or locking mechanism Adds a premium, purposeful look to a frequently overlooked area of the interior Compatibility Vehicle Code Year Range Fitment Land Rover Defender 110 L663 2020–2021 Direct Fit Land Rover Defender 90 L663 2020–2021 Verify Before Purchase Land Rover Defender 130 L663 2022–2024 Not Compatible Land Rover Defender 110 L663 2022–2024 Not Compatible Range Rover Sport L494 2013–2020 Not Compatible Range Rover Vogue L405 2013–2020 Not Compatible Installation Notes ⏱ Estimated Time: 15–20 minutes  |  🛠 Difficulty: Easy — No Tools Required Open the Defender 110 tailgate fully and ensure the interior panel surface is clean, dry, and free from dust, grease, or wax residue. Use an isopropyl alcohol wipe for best results. Dry-fit the carbon fiber panel against the tailgate trim area to confirm alignment and positioning before committing to adhesive contact. Peel back a small section of the adhesive backing tape, align one edge of the panel carefully, and press firmly into position. Gradually peel the remaining backing tape whilst pressing the panel flat against the surface — work from the centre outward to avoid trapping air bubbles. Apply firm, even pressure across the entire panel surface for 30–60 seconds. Allow the adhesive to cure for at least 2 hours before loading the vehicle. ⚠ Note: Do not install in temperatures below 10°C / 50°F — cold conditions reduce adhesive bond strength. Ensure the surface is completely dry before application. Once bonded, avoid removing and re-applying the panel as this may compromise adhesive performance. Complete Your Defender 110 Interior Explore our full range of precision-fit interior trim and protection accessories for the Defender L663 — every piece designed to complement the vehicle without compromise. Shop Defender 110 Accessories Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 📦 Worldwide Shipping via DHL, FedEx & UPS ↩ 30-Day Money-Back Guarantee 📞 +44 203 943 9919 Mon–Fri 9am–7pm Victorious Automotive is an independent retailer of aftermarket and accessory products for Land Rover and Range Rover vehicles. This product is not manufactured by, endorsed by, or affiliated with Land Rover, Jaguar Land Rover Limited (JLR), or any of their subsidiaries. All vehicle names, model codes, and trademarks referenced are used solely for fitment identification purposes and remain the property of their respective owners. Always verify compatibility with your specific vehicle specification before purchase.

Victorious · Defender L663 · Storage Tailgate Window Storage Bag for Defender 90, 110 & 130 Keep essential gear organised and accessible with this purpose-built tailgate window storage solution for your modern Defender. L663 2020–2026 Multi-Pocket Design Direct Fit Tool Storage Overview Whether you're driving a Defender 90, 110, or 130, managing loose items in the cabin can become frustrating quickly. Tools, recovery gear, and daily essentials need a dedicated home—not rolling around the footwell or sliding across the dashboard during rough terrain. This Tailgate Window Storage Bag mounts directly to your Defender's rear window frame, transforming unused space into intelligent, accessible storage. The multi-pocket design keeps items organised and within arm's reach, while the purpose-engineered fit ensures no interference with visibility or functionality. Made to ISO9001 standards in premium facilities, it's built to withstand the demands of serious Defender ownership. Ideal for recovery kit components, tools, charging cables, maps, or emergency supplies—this is the kind of practical upgrade that makes every expedition feel more prepared and professional. What's Included 🎒 Storage Bag Assembly Multi-pocket organiser with mounting hardware 🔧 Fixing Brackets Stainless steel or polymer attachment points 📋 Installation Guide Step-by-step instructions for L663 models ✓ Quality Assurance ISO9001 certified manufacturing standard Product Highlights Tailgate window-mounted design—zero impact on cabin layout Multiple organised pockets for efficient gear separation Engineered for Defender 90, 110, and 130 models Durable materials built for off-road and daily use Tool and recovery kit ready—practical load capacity Easy installation without permanent modifications Direct-fit compatibility with 2020–2026 L663 generation Maintains full rear visibility and operational access ISO9001 factory quality—export-standard durability Protects cargo from road spray and weather exposure Compatibility Vehicle Model Year Range Fit Status Defender 90 (L663) 2020–2026 Direct Fit Defender 110 (L663) 2020–2026 Direct Fit Defender 130 (L663) 2020–2026 Direct Fit Defender (Pre-L663) 2004–2019 Not Compatible Range Rover / Sport All Not Compatible Installation Difficulty: Easy | Time: 15–20 minutes Open your Defender's tailgate fully and secure in position. Locate the window frame attachment points on the upper tailgate panel. Align the storage bag brackets with the mounting holes—brackets should sit flush against the frame. Fasten using the provided hardware (no drilling required); tighten evenly to ensure level installation. Load your gear gradually, testing that the bag sits securely and does not rattle during movement. Confirm rear visibility is unobstructed and the tailgate closes freely. Note: Avoid exceeding the designed load capacity to maintain structural integrity and prevent frame stress. Always check fitment after the first off-road outing to ensure hardware remains secure. Ready to Organise Your Defender? Smart storage transforms your Defender from a capable truck into a prepared, mission-ready companion. This tailgate window bag delivers exactly that—accessible, secure, and built to the standards Defender owners demand. Shop Defender Accessories Save 20% on two items with code 22GET20 4.9★ 12,300+ reviews ✓ 30-day money-back guarantee 📦 Worldwide DHL, FedEx, UPS 📞 +44 203 943 9919 Mon–Fri 9am–7pm Victorious Automotive is an independent aftermarket specialist and is not affiliated with Land Rover, Range Rover, Jaguar Land Rover, or any official Land Rover subsidiary. All product names and vehicle designations are used for compatibility reference only. Always consult your vehicle handbook and contact our team with any compatibility questions before purchase.

Victorious · Defender 110 · Storage Aluminum Alloy Trunk Right Storage Basket – Defender 110 L663 Premium multifunctional cargo organization for your 2020–2024 Defender 110, engineered from aerospace-grade aluminum alloy with precision fit and effortless installation. L663 2020–2024 Aluminum Alloy Trunk Storage Right Side Multifunctional Direct Fit Overview The Defender 110 L663 demands storage solutions that match its capability and character. Victorious has engineered this aluminum alloy trunk basket specifically for your 2020–2024 model, designed to maximize cargo capacity while maintaining the refined aesthetics your Defender deserves. Built from high-grade aluminum alloy, this storage basket combines lightweight durability with genuine resistance to scratches, wear, and corrosion. The right-side trunk placement provides intuitive access to frequently used gear, tools, or recovery equipment—without compromising interior space or comfort. Every basket is manufactured to ISO9001 standards in certified facilities and tested across thousands of Defenders worldwide. Installation takes minutes. The double-sided 3M adhesive backing requires zero drilling, modifications, or professional fitting. Simply clean, apply, and secure—your Defender's factory finish remains completely untouched. This is direct-fit engineering at its finest: no compromise on quality, no headache on installation day. What's Included 📦 Aluminum Alloy Basket Right trunk, finished black 🔧 3M Adhesive Backing Pre-applied, no tools needed 📋 Installation Guide Step-by-step, with fitment photos 🎁 Retail Packaging 100% new, boxed, ready to gift Product Highlights Aerospace-grade aluminum alloy – lightweight yet rigid Scratch and wear resistant – engineered for expedition use ISO9001 certified manufacturing – global quality standard 3M double-sided adhesive – no drilling, no tools required Right-side trunk placement – optimized cargo flow Black powder-coated finish – matches modern Defender interiors Precision-fit design – engineered for L663 2020–2024 only Multifunctional storage – tools, recovery, adventure gear Corrosion-resistant – tested in harsh climates worldwide Reversible fitment – returns to factory state with adhesive remover Compatibility Model Years Code Fitment Defender 110 2020–2024 L663 Direct Fit Defender 110 2016–2019 L550 Not Compatible Defender 90 2020–2024 L663 Not Compatible Defender 130 2020–2024 L663 Not Compatible Before ordering: Cross-reference your VIN or vehicle documentation with the L663 code and 2020–2024 production date. Fitment is specific to Defender 110 models only. If unsure, contact us at +44 203 943 9919 (Mon–Fri 9am–7pm). Installation Difficulty: Beginner | Time: 5–10 minutes Prepare the surface. Clean the trunk area thoroughly with a lint-free cloth. Remove any dust, dirt, or residue. Allow 10 minutes for full drying. Verify fitment. Position the basket against the right trunk wall. Confirm alignment matches factory contours. Do not apply adhesive yet. Peel backing. Carefully remove the 3M adhesive backing from the rear face of the basket. Apply basket. Press firmly into position, starting from the top and working downward. Hold for 30 seconds to ensure full contact. Cure time. Do not wash, vacuum, or stress the adhesive for 48 hours. Allow the 3M bond to reach full strength. Load gradually. Start with light loads (5–10 kg) in the first week, then increase to full capacity as needed. Important: Do not install in temperatures below 10°C or above 40°C. Adhesive performance is optimized at room temperature. If removal is necessary later, use 90% isopropyl alcohol and a plastic scraper to gently lift the basket without damaging trim. Ready to Organize Your Defender 110? This aluminum alloy storage basket is built for explorers, weekend warriors, and everyday drivers who refuse to compromise on quality. Every basket is tested, certified, and backed by our 30-day money-back guarantee and worldwide shipping via DHL, FedEx, or UPS. Shop Defender 110 Accessories Save 20% on any 2 items. Use code 22GET20 at checkout. 4.9/5 · 12,300+ reviews 30-day money-back guarantee Worldwide shipping included Expert support Mon–Fri 9am–7pm Victorious Automotive is an independent aftermarket specialist. This product is not manufactured, endorsed, or affiliated with Land Rover, Jaguar Land Rover, or any official Land Rover subsidiary. All vehicle names and model codes are used for identification and compatibility purposes only. Fitment and performance are guaranteed for Defender 110 L663 models (2020–2024) only. Always verify your specific vehicle variant before purchase.

Victorious Automotive · Defender L663 · Interior Trim Land Rover Defender L663 110 Carbon Fibre Centre Console Air Outlet Frame (2020–2021) A precision-cut carbon fibre style trim that upgrades the Defender 110's centre console air vents with a refined, performance-inspired finish — installed in minutes, no tools required. Defender L663 2020–2021 Carbon Fibre ABS Centre Console Trim Air Outlet Frame No-Drill Install ISO9001 Certified Model: LLK2928 Overview The 2020–2021 Land Rover Defender 110 (L663) was engineered as a modern reinterpretation of one of the world's most iconic 4x4s. Its interior marked a dramatic shift — functional, purposeful, and built around a driver-first philosophy. For enthusiasts who want that interior to reflect their standards as much as their vehicle's capability, every detail matters. This centre console air outlet frame is designed specifically for the L663 Defender 110's 2020 and 2021 model years, fitting neatly over the factory air vent surrounds to deliver a clean carbon fibre aesthetic. The ABS substrate is finished with a genuine carbon fibre weave pattern, giving it the visual depth and texture of real carbon — at a weight and cost that makes sense for an interior upgrade of this nature. Where the factory plastic surround blends into the dashboard, this trim immediately draws the eye and grounds the centre console with a more purposeful, motorsport-influenced character. It complements both dark and light interior colour packs equally well, and pairs naturally with other carbon fibre or brushed metal interior upgrades throughout the L663 cabin. What's Included 🖤 Carbon Fibre Air Outlet Frame 1 x centre console trim piece, model LLK2928 🔧 Pre-Applied Adhesive Tape Automotive-grade 3M-style mounting tape 📄 Installation Guide Basic fitting reference included in packaging Product Highlights Precision-engineered for the Defender L663 110 (2020–2021) centre console air vent surround Carbon fibre weave ABS construction — lightweight, durable, and heat-resistant Retains full vent functionality — no impact on airflow or adjustment No drilling, cutting, or modification to factory components required Adhesive mounting system allows clean removal without residue damage ISO9001-certified manufacturing for consistent quality and fit tolerances Dimensions: 40cm (L) × 15cm (W) × 10cm (H) — engineered to OEM proportions Weighs just 300g — adds zero meaningful mass to the vehicle Pairs seamlessly with other L663 carbon fibre interior trim upgrades Direct, like-for-like fitment tested against 2020 and 2021 production Defender 110 interiors Compatibility Vehicle Code Years Fitment Land Rover Defender 110 L663 2020–2021 Direct Fit Land Rover Defender 90 L663 2020–2021 Verify Before Purchase Land Rover Defender 110 L663 2022–2026 Not Confirmed Range Rover Vogue L405 / L460 All Years Not Compatible Range Rover Sport L494 / L461 All Years Not Compatible Range Rover Velar L560 All Years Not Compatible Installation Notes ⏱ Estimated Time: 10–15 minutes  |  🛠 Difficulty: Beginner Begin with the vehicle at rest and the interior at room temperature — avoid fitting in direct sunlight or cold conditions where the adhesive may not bond correctly. Identify the centre console air outlet surround on your Defender 110. This sits centrally between the front seats, framing the horizontal vent array. Thoroughly clean the factory plastic surface using an isopropyl alcohol wipe or panel prep solution. Remove all dust, oils, and residue. Allow to dry completely. Test-fit the carbon fibre frame without removing the adhesive backing to confirm alignment and positioning. Note any reference points. Peel the adhesive backing and carefully position the trim, pressing firmly from the centre outward to eliminate air pockets. Apply sustained pressure for 30–60 seconds across the full surface. Allow the adhesive to cure for a minimum of 2 hours before touching or stressing the trim. Full bond strength is typically achieved within 24 hours. ⚠ Note: Ensure the adhesive surface is fully dry before fitting. Do not attempt installation immediately after cleaning — residual moisture will compromise the bond. If fitting in winter, warm the panel gently with a hairdryer before applying the trim. Upgrade Your Defender's Interior Explore our full range of Defender L663 interior accessories — from carbon fibre dash trim to instrument cluster surrounds — and build the cabin your Defender deserves. Shop Defender L663 Collection → Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 🚚 Worldwide Shipping via DHL, FedEx, UPS & TNT 🔁 30-Day Money-Back Guarantee 📞 +44 203 943 9919 Mon–Fri, 9am–7pm Victorious Automotive is an independent aftermarket accessories retailer. This product is not manufactured by, affiliated with, or endorsed by Land Rover, Jaguar Land Rover Limited (JLR), or any of their subsidiaries. All vehicle names, model codes, and trademarks are the property of their respective owners and are used solely for compatibility reference purposes.

Victorious Automotive · Defender L663 · Interior Trim Land Rover Defender 110 & 130 Aluminum Alloy Silver Door Speaker Cover Panel Trim — Set of 8 A precision-machined set of eight aluminum alloy speaker cover trims that replace the factory plastic finish with a refined, industrial-grade silver aesthetic — purpose-built for the 2020-onwards Defender L663. Defender L663 2020–2026 Set of 8 Aluminum Alloy Silver Door Speaker Trim Peel & Stick ISO9001 Certified Model: XYL0341 Overview The Land Rover Defender L663 was engineered to be capable without compromise — and its interior deserves the same standard. Whether you're driving a 110 or the longer-wheelbase 130, the cabin is a space you spend serious time in, and every surface matters. The door speaker surrounds are a subtle but consistently visible detail, and the factory plastic finish — functional as it is — leaves room for meaningful improvement. These aluminum alloy speaker cover panel trims are machined to match the precise dimensions and mounting geometry of the Defender L663's door speaker housings. Finished in a clean, brushed silver tone, they complement the Defender's utilitarian-meets-refined design language without trying to over-style it. The result is a cohesive upgrade that looks factory-correct but noticeably more premium. The complete set of eight covers every speaker position across the front and rear doors of the 110 and 130, meaning the cabin reads as consistently upgraded throughout — not a piecemeal modification. Installation requires no tools and no permanent modification to your vehicle: each trim bonds cleanly using a professional-grade peel-and-stick adhesive system, making this one of the most impactful interior changes you can make in under an hour. What's Included 🔊 8× Speaker Cover Trims Full set — front and rear door positions covered 🔩 Pre-Applied Adhesive 3M-grade peel-and-stick backing on each trim 📋 Installation Guide Step-by-step fitting instructions included 📦 Protective Packaging Each piece individually wrapped to prevent transit damage Product Highlights Precision-formed aluminum alloy construction for lasting rigidity and a quality-forward feel Brushed silver finish complements the Defender's interior design language naturally Complete set of 8 trims covers every door speaker position in the 110 and 130 Peel-and-stick installation — no drilling, no screws, no permanent modifications ISO9001 certified manufacturing ensures consistent dimensional accuracy across every piece Engineered specifically for the 2020-onwards Defender L663 body and door profile Lightweight at 300g total, with no impact on door close feel or weight distribution Resistant to everyday cabin wear — UV stable and easy to wipe clean Each trim measures 14cm × 14cm × 3cm for a precise, flush fit against factory panels Immediately reversible — no trace left on the original panels if removed Compatibility Vehicle Model Code Year Range Compatibility Land Rover Defender 110 L663 2020–2026 Direct Fit Land Rover Defender 130 L663 2020–2026 Direct Fit Land Rover Defender 90 L663 2020–2026 Verify Before Purchase Range Rover Sport L461 L461 2022–2026 Not Compatible Range Rover Vogue L460 L460 2022–2026 Not Compatible Range Rover Vogue L405 L405 2013–2020 Not Compatible Range Rover Sport L494 L494 2013–2020 Not Compatible Range Rover Velar L560 2018–2022 Not Compatible Installation Notes Difficulty: Easy  ·  Estimated Time: 30–45 minutes  ·  Tools Required: None Start with a clean, dry cabin — allow the vehicle to reach ambient room temperature if possible. Cold interiors (below 10°C) can reduce initial adhesive bond strength. Using a microfibre cloth lightly dampened with isopropyl alcohol, clean each factory speaker panel surface to remove any dust, oils, or residue. Allow to dry fully for 2–3 minutes. Dry-fit each trim piece against its corresponding speaker panel before committing. Confirm alignment and confirm the trim sits flush with no gaps at the edges. Peel the protective backing from the adhesive layer on the first trim. Position carefully over the speaker panel — the adhesive bonds on first contact, so take your time aligning before pressing. Apply firm, even pressure across the full surface of the trim for 30–60 seconds to activate the adhesive bond. Work outward from the centre to avoid air pockets. Repeat for all remaining trims, working systematically across front doors before moving to rear doors. Allow 24 hours before exposing the trims to moisture or direct sunlight, giving the adhesive time to fully cure for a permanent hold. ⚠ Important: Confirm fitment for the Defender 90 before purchasing — speaker panel geometry may differ from the 110 and 130 variants. If you are unsure, contact our team on +44 203 943 9919 (Mon–Fri, 9am–7pm) and we'll confirm compatibility for your specific build date and specification. Upgrade Your Defender's Interior Today Explore our full range of Defender L663 interior accessories — designed by enthusiasts, built to the standard your Land Rover deserves. Shop All Defender L663 Accessories Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 Stars from 12,300+ verified reviews 🔄 30-Day money-back guarantee 🚚 Worldwide shipping via DHL, FedEx, UPS & TNT 📞 Expert support +44 203 943 9919 Victorious Automotive is an independent aftermarket accessories retailer. This product is not manufactured by, affiliated with, or endorsed by Land Rover, Jaguar Land Rover Limited (JLR), or any of their subsidiaries. All vehicle model names, codes, and trademarks referenced are the property of their respective owners and are used solely for fitment identification purposes. Please verify compatibility with your specific vehicle before purchasing.

Victorious · Defender L663 · Interior Storage Aluminum Central Control Side Storage Bag Rack for Defender 90 & 110 Premium multi-function storage solution engineered to maximize cabin organization and interior refinement across the modern Defender range. Defender 90 / 110 2020–2024 Aluminum Alloy Direct Fit Adhesive Mount ISO 9001 Overview The Defender 90 and 110 (2020–2024) represent a decisive modernization of Land Rover's most iconic platform. Retaining uncompromising off-road pedigree, today's Defender demands cabin solutions that blend heritage practicality with contemporary aesthetics. This aluminum central control side storage rack addresses a genuine constraint: usable cabin storage that doesn't compromise design integrity. Constructed from aerospace-grade aluminum alloy and finished in subtle black, this multi-function rack mounts directly to the central control panel, creating dedicated storage for essentials—phones, cards, small accessories, navigation aids. Unlike flimsy clip-on alternatives, it becomes a permanent architectural element of your cabin, improving visual depth whilst eliminating dashboard clutter. Manufactured to ISO 9001 standards and already deployed across Land Rover markets globally, it's engineered for durability: scratch-resistant, wear-resistant, and purposefully designed to complement Defender's interior language. Simple adhesive installation means no drilling, no permanent modification, and reversibility if required. What's Included 📦 Aluminum Storage Rack Central control side-mounted module 🔧 3M Adhesive Strip Dual-sided mounting tape, pre-applied 📋 Installation Guide Step-by-step instructions included 🎁 Retail Packaging 100% new, factory-sealed box Key Features Aerospace-grade aluminum alloy construction Scratch- and wear-resistant surface treatment Direct-fit design for Defender 90 & 110 (2020–2024) Integrated multi-function storage compartments Matte black finish—integrates seamlessly with modern Defender interiors No drilling required—3M adhesive installation only ISO 9001 certified manufacturing Globally proven design—exported to 50+ markets Easy to install and reversible Improves cabin organization and visual tidiness Compatibility Model Year Range Fitment Defender 90 2020–2024 Direct Fit Defender 110 2020–2024 Direct Fit Defender 130 2021–2024 Verify Fit Older Defender (1983–2016) Pre-2020 Not Compatible Note: Always confirm fitment by comparing your vehicle's central control panel layout with provided images before ordering. Contact our team (+44 203 943 9919) with photos if unsure. Installation Difficulty: Beginner | Time: 10–15 minutes Prepare the surface: Clean the central control panel mounting area thoroughly with a microfibre cloth. Ensure no dust, dirt, or residue remains. Allow to dry completely. Remove adhesive backing: Gently peel the 3M protective film from the pre-applied dual-sided tape on the rear of the rack. Position and align: Carefully align the rack with your central control panel. Reference the provided images to confirm exact placement. Press firmly for 20–30 seconds to establish initial adhesion. Allow cure time: Do not wash or stress the vehicle for 48 hours. The adhesive requires full curing time to achieve maximum bond strength. Test security: After 48 hours, gently press and flex the rack to confirm stable mounting. It should move minimally if at all. ⚠️ Important: Failure to clean the mounting surface thoroughly will compromise adhesion. If your Defender has a textured or heavily contoured central control panel, the rack may not sit flush. Contact us before installation if you're uncertain about panel geometry. Ready to Refine Your Cabin Transform your Defender's central console into a purpose-built storage hub. This premium aluminum rack eliminates clutter, enhances interior organization, and restores cabin elegance—all without permanent modification. Shop Defender Storage Solutions Use code 22GET20 for 20% off any 2 items 4.9★ 12,300+ verified reviews ✓ 30-day money-back guarantee ✓ Worldwide shipping via DHL/FedEx ✓ +44 203 943 9919 (Mon–Fri 9am–7pm) Disclaimer: Victorious Automotive is an independent aftermarket specialist and is not affiliated with, endorsed by, or connected to Land Rover, Jaguar Land Rover Holdings, or any official Land Rover entity. All references to Land Rover, Defender, and related trademarks are for identification purposes only. Product fitment is the customer's responsibility; please verify compatibility before purchase.

Victorious Automotive · Defender L663 · Interior Protection ABS Carbon Fiber Rear Armrest Box Anti-Kick Cover for Land Rover Defender 110 & 130 (2020+) A precision-formed ABS carbon fibre kick cover that guards the rear armrest box of your Defender L663 against everyday scuffs, scratches, and heel damage — with a factory-finish aesthetic that looks entirely at home. Defender L663 2020–2026 High-Quality ABS Carbon Fibre Finish Anti-Kick Protection No-Drill Install Rear Armrest Box Model: XYL1446 Overview The Land Rover Defender 110 and 130 (L663, 2020 onwards) represents an entirely new chapter for one of the most iconic vehicles ever made — and its interior reflects that ambition. Clean lines, purposeful surfaces, and a level of refinement that earlier Defenders never offered. Protecting those surfaces from the inevitable wear of daily life is where this rear armrest box anti-kick cover comes in. Engineered specifically for the rear centre armrest box panel area of the L663 Defender, this cover wraps the lower section in a durable, high-quality ABS shell finished in a striking carbon fibre texture. This is the zone that takes the most punishment from rear passengers — boots, bags, and casual contact all take their toll. Without protection, scuffs and scratches accumulate quickly and are disproportionately noticeable on an otherwise clean interior. The fit is precise and purposeful. Using automotive-grade adhesive tape, this cover applies cleanly without drilling, cutting, or any modification to the vehicle's original trim. The carbon fibre finish integrates naturally with the Defender's utilitarian-premium aesthetic, adding a layer of visual intent without looking out of place. A small upgrade with a quietly significant impact on the long-term condition of your interior. What's Included 🛡️ Anti-Kick Cover 1 × ABS carbon fibre rear armrest box protection panel 🔧 Adhesive Tape Pre-applied automotive-grade 3M-style mounting tape 📋 Installation Guide Step-by-step fitting instructions included Product Highlights Designed exclusively for the Defender L663 110 & 130 (2020+) Premium ABS construction — rigid, lightweight, and durable Carbon fibre texture finish for a refined, sporty aesthetic Guards against scuffs, heel strikes, and surface scratches No-drill, no-modification installation — fully reversible Automotive-grade adhesive tape pre-applied for clean fitment Exact dimensions: 34cm (L) × 30cm (W) × 6cm (H) Lightweight at just 366g — no impact on vehicle dynamics Complements factory trim without looking aftermarket Maintains original panel access and armrest functionality Compatibility Vehicle Code Year Range Fit Land Rover Defender 110 L663 2020–2026 Direct Fit Land Rover Defender 130 L663 2020–2026 Direct Fit Land Rover Defender 90 L663 2020–2026 Verify Before Purchase Defender (Original) Pre-2016 All Years Not Compatible Range Rover Sport L494 / L461 All Years Not Compatible Range Rover Vogue L405 / L460 All Years Not Compatible Installation Notes Difficulty: Easy  ·  Estimated Time: 15–20 minutes  ·  Tools Required: None Begin by thoroughly cleaning the rear armrest box panel surface using an isopropyl alcohol wipe. Remove all dust, grease, and moisture, and allow to dry completely before proceeding. Offer the cover up to the panel to confirm alignment and fitment before removing any adhesive backing. Note the orientation and any contour points. Peel back a small section of the adhesive backing to expose the tape. Carefully position the cover from one edge, pressing firmly as you work across the surface to avoid air pockets. Once fully seated, apply firm and even pressure across the entire cover for 30–60 seconds to ensure maximum adhesive contact with the panel surface. Allow at least 72 hours before subjecting the cover to heavy use or pressure, giving the adhesive bond time to fully cure. Note: Do not apply in temperatures below 10°C — cold surfaces significantly reduce adhesive performance. Ensure the vehicle has been at room temperature for at least one hour before fitting. If your vehicle has been recently detailed or treated with a silicone-based product, clean the surface thoroughly before installation. Complete Your Defender's Interior Browse our full collection of Defender L663 interior accessories — from carbon fibre trims and armrest covers to dashboard overlays and door panel protectors. Every piece is selected to complement the Defender's character without compromising it. Shop Defender L663 Interior → 22GET20 — 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 📦 Worldwide Shipping via DHL, FedEx & UPS ↩️ 30-Day Money-Back Guarantee 📞 +44 203 943 9919 Mon–Fri, 9am–7pm Victorious Automotive is an independent aftermarket accessory retailer. We are not affiliated with, endorsed by, or an authorised dealer of Land Rover, Jaguar Land Rover (JLR), or any of their subsidiaries. All vehicle names, model codes, and trademarks referenced are the property of their respective owners and are used solely for fitment identification purposes. Always verify compatibility with your specific vehicle variant before purchase.

Victorious Automotive · Defender 110 · Interior Trim Stainless Steel Black Interior Door Decorative Panel Trim for Defender 110 Premium stainless steel door panel upgrade that elevates your Defender 110's cabin aesthetic with a seamless, factory-quality finish. Defender 110 L663 2020–2025 Stainless Steel Direct Fit Adhesive Install Overview The Defender 110 is built for adventure, but the cabin deserves refinement. This stainless steel interior door trim panel upgrade transforms your door cards with a sophisticated black-finished accent that catches light beautifully and complements both modern and classic Defender interiors. Manufactured from premium-grade stainless steel and finished with a durable black coating, these panels are engineered to resist daily wear, scratches, and UV fading. The 3M adhesive backing ensures a permanent, rattle-free installation without drilling, fasteners, or modification to factory components. Whether you're refining your daily driver or building a bespoke expedition rig, this upgrade delivers a proportionate, understated luxury touch that Defender enthusiasts appreciate—subtle enough to feel authentic, striking enough to turn heads at the car park. What's Included 📦 Interior Door Panels (Set) Stainless steel with black finish 🔧 3M Adhesive Backing Pre-applied, ready to install 📋 Installation Guide Step-by-step, with prep tips ✓ Factory Packaging 100% new, unboxed condition Product Highlights Premium stainless steel construction with corrosion resistance Durable black anodized finish resists fingerprints and UV fade Direct fit for Defender 110 L663 (2020–2025) 3M adhesive backing—no drilling or fasteners required ISO 9001 certified manufacturing and quality control Scratch and wear resistant for long-term durability Seamless integration with factory door card design Quick, tool-free installation in under 30 minutes Improves visual appeal and perceived cabin quality Worldwide shipping via DHL, FedEx, UPS, or TNT Compatibility Vehicle Model Year Range Fitment Status Land Rover Defender 110 (L663) 2020–2025 Direct Fit Land Rover Defender 110 (L663) Pre-2020 Not Compatible Land Rover Defender 90 All Years Not Compatible Range Rover / Range Rover Sport All Years Not Compatible Note: Always verify fitment against your VIN and door card profile before ordering. Contact our team at +44 203 943 9919 if unsure. Installation Difficulty Level: Beginner | Time: 20–30 minutes Prepare the surface. Clean the door card thoroughly with a dry cloth to remove all dust, fingerprints, and debris. A clean surface is essential for adhesive bonding. Position and align. Dry-fit the panel against your door card to confirm placement and alignment. Use the factory geometry and any trim lines as guides. Remove adhesive backing. Carefully peel the 3M protective film from the rear of the stainless steel panel. Apply firmly. Press the panel onto the door card with steady, even pressure, starting from one edge and working across to avoid air pockets. Allow cure time. Do not wash, wipe, or apply moisture to the vehicle for 48 hours. This allows the adhesive to fully set and cure. ⚠️ Important: Confirm the panel matches your door card profile before removing the adhesive backing. Once applied, adhesive removal may damage the door card trim. If misaligned, carefully peel back slowly and reposition before the adhesive fully sets. Why Choose Victorious Automotive We specialise exclusively in Land Rover, Range Rover, and Defender accessories. Every product is vetted for quality, compatibility, and real-world durability by our in-house enthusiast team. This trim panel has been tested across thousands of Defender 110 builds and delivers consistent, professional results. Your satisfaction is guaranteed: if this panel doesn't meet your expectations, we'll refund or replace it within 30 days—no questions asked. Ready to Refine Your Cabin? Add this premium stainless steel interior door trim to your Defender 110 and experience the subtle luxury that sets your rig apart. Direct fit, durable, and designed for enthusiasts. Shop Defender 110 Accessories Save 20% when you buy any 2 items. Use code: 22GET20 ✓ 4.9/5 stars from 12,300+ verified reviews ✓ 30-day money-back guarantee ✓ Worldwide shipping via DHL, FedEx, UPS, TNT ✓ Expert support +44 203 943 9919 (Mon–Fri 9am–7pm) Victorious Automotive is an independent aftermarket specialist and is not affiliated with Land Rover, Jaguar Land Rover, or any official Land Rover dealer. All vehicle names, logos, and trademarks are the property of their respective manufacturers. This product is designed for aftermarket enhancement only.

Victorious Automotive · Defender L663 · Cargo Organisation Trunk Divider Net for Land Rover Defender 110 & 90 (2020–2024) — L663 Custom-Fit Cargo Isolation Net A precision-engineered trunk divider net built exclusively for the L663 Defender — keeping luggage contained, pets separated, and your load bay organised on every journey. Defender L663 2020–2024 110 & 90 Premium Mesh Custom Fit Cargo Divider No-Drill Install Pet & Luggage Safe Overview The Land Rover Defender L663 was engineered for those who go further — whether that's a weekend trail, a cross-country overland build, or a daily drive that demands total practicality. The load bay of the Defender 110 and 90 is generous by design, but without the right organisation, loose cargo shifts, slides, and compromises both safety and the integrity of your interior. This Trunk Divider Net is purpose-built for the 2020–2024 Defender L663 platform, designed to slot precisely into the rear cargo area and create a defined barrier between luggage, equipment, and passengers or pets. The high-tensile mesh construction absorbs impact forces without stretching out of shape, and the mounting hardware integrates cleanly with existing anchor points — no drilling, no modification, and no permanent alteration to your vehicle. For Defender owners who treat their vehicle as a tool as much as a statement, this net delivers the kind of quiet, reliable functionality that simply works. It installs in minutes, disappears into the cabin aesthetic, and gives you confidence that what's behind the rear seats stays exactly where you put it — whatever the terrain. What's Included 🕸️ Trunk Divider Net Custom-fit mesh net for L663 Defender load bay 🔩 Mounting Hardware Set All fixings and clips required for installation 🪝 Anchor Hooks Heavy-duty hooks for load point attachment 📋 Installation Guide Step-by-step instructions included — manual available on request Product Highlights Custom-engineered fit for the Defender L663 110 and 90 load bay dimensions High-tensile premium mesh retains shape under sustained load and impact Tool-free installation — mounts to existing anchor points with no drilling Effectively isolates pets, luggage, and equipment from the passenger cabin Discreet low-profile design integrates with the Defender's utilitarian interior Reinforced edge stitching and durable border framing for long-term durability Fully adjustable tensioning to suit varying cargo heights and configurations Compatible with Defender 110 five-seat and seven-seat load configurations Removable and re-installable without tools — collapses flat for easy storage Ideal for overlanding, family travel, working vehicles, and pet transport Compatibility Model Year Range Variant Fit Defender 110 (L663) 2020–2024 5-Seat & 7-Seat Direct Fit Defender 90 (L663) 2020–2024 Standard Direct Fit Defender 130 (L663) 2022–2024 8-Seat Not Compatible Defender 110 (Pre-2020) Pre-2020 Previous Generation Not Compatible Range Rover Sport (L461) 2022–2026 All Variants Not Compatible Range Rover Vogue (L460) 2022–2026 All Variants Not Compatible Installation Notes Difficulty: Easy  ·  Estimated Time: 10–15 Minutes  ·  Tools Required: None Open the Defender's rear tailgate and fold or remove any rear seat configurations as needed to access the full load bay area. Locate the existing OEM cargo anchor points and load loops in the boot — these are the primary attachment locations for the divider net. Attach the anchor hooks from the mounting hardware set to the designated load anchor points on both the floor and the upper load area brackets. Unroll and position the trunk divider net vertically across the desired separation point in the load bay, aligning the top and bottom edges with the hook attachment positions. Clip the net border to each anchor hook, working from one side to the other to ensure even tension across the full width of the net. Adjust the tensioning where applicable to ensure the net sits taut, upright, and flush — confirming there is no excess slack that could allow cargo movement. Close the tailgate and perform a brief check from the passenger cabin side to confirm the net is secure and correctly positioned before driving. ⚠ Important: Always verify your specific Defender variant and model year before purchasing. The Defender 90 and 110 share this net's compatibility, but load bay dimensions may vary slightly between seating configurations. Contact us on +44 203 943 9919 (Mon–Fri, 9am–7pm) if you have any fitment questions before ordering. Complete Your Defender L663 Interior Explore our full range of Defender 110 and 90 accessories — from boot liners and cargo organizers to interior protection and styling upgrades, all engineered to the same standard. Shop Defender L663 Accessories → Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 🚚 Worldwide Shipping via DHL, FedEx & UPS ↩️ 30-Day Money-Back Guarantee 📞 Expert Support Mon–Fri, 9am–7pm Victorious Automotive is an independent aftermarket accessories retailer and is not affiliated with, endorsed by, or connected to Land Rover, Jaguar Land Rover Limited (JLR), or any of their subsidiaries. All vehicle names, model codes, and trademarks referenced — including Defender, Land Rover, and L663 — are the property of their respective owners and are used solely for the purpose of product fitment identification.

Victorious Automotive · Defender L663 · Interior Trim ABS Carbon Fibre Seat Adjustment Frame Side Covers – Land Rover Defender 110 (2020–2021) A precision-fit interior upgrade that shields your Defender's seat adjustment frames from daily wear while delivering a sharp, purposeful carbon fibre aesthetic. Defender L663 2020–2021 ABS Carbon Fibre Seat Frame Covers Peel & Stick No Drilling Interior Trim Direct Fit Overview The Land Rover Defender 110 in its L663 generation brought a genuinely modern interior to a vehicle that had long traded on its raw mechanical character. For owners who have invested in that interior — whether in SE, S, X-Dynamic, or First Edition trim — maintaining the quality of every surface matters. The seat adjustment frame area, subject to constant contact from shoes, bags, and daily use, is one of the first places wear begins to show. These ABS carbon fibre seat adjustment frame side covers are engineered specifically for the 2020 and 2021 model year Defender 110. Each piece is formed from high-grade ABS and finished in a woven carbon fibre texture that reads as genuinely premium in person. They sit flush against the seat frame surround, covering the exposed base sections on both the driver and front passenger sides, protecting the original plastic from scuffs, scrapes, and UV fading without altering the seat's adjustability in any way. Installation requires no tools, no drilling, and no professional fitting — automotive-grade adhesive tape is pre-applied to the reverse of each cover, creating a bond that holds firmly through temperature variation and vibration. It's the kind of detail that Defender owners notice immediately, and that passengers simply assume was there from the factory. What's Included 🪑 Driver Side Cover Carbon fibre ABS, left-hand seat frame 🪑 Passenger Side Cover Carbon fibre ABS, right-hand seat frame 🔧 Pre-Applied Adhesive Automotive-grade tape, no tools required 📄 Installation Guide Step-by-step fitting instructions included Product Highlights Precision-moulded for the 2020–2021 Defender 110 seat frame geometry High-grade ABS construction with woven carbon fibre surface finish Protects original seat frame plastic from scuffs, scratches, and wear Pre-applied automotive adhesive tape for a clean, tool-free installation Does not impede seat adjustment levers, rails, or mechanisms Colour-consistent carbon texture that complements factory interior trim Resistant to temperature fluctuation and interior UV exposure Low-profile fit — no visible gaps, no lifting edges once bonded Covers both front seats — driver and passenger included as a pair Reversible installation — removable without damage to original surfaces Compatibility Vehicle Code Years Fit Land Rover Defender 110 L663 2020–2021 Direct Fit Land Rover Defender 90 L663 2020–2021 Verify Before Purchase Land Rover Defender 130 L663 2022–2026 Not Compatible Range Rover Sport L494 / L461 All Years Not Compatible Range Rover Vogue L405 / L460 All Years Not Compatible Range Rover Velar L560 All Years Not Compatible Installation Notes ⏱ Estimated Time: 15–20 minutes  ·  🟢 Difficulty: Beginner Begin with both front seats fully accessible. Push each seat back to expose the lower frame surround and give yourself clear working space. Thoroughly clean the seat frame surface using an isopropyl alcohol wipe or equivalent. Remove all dust, grease, and residue — adhesion quality depends entirely on surface preparation. Allow the cleaned surface to dry completely for at least 2–3 minutes before proceeding. Test-fit each cover dry before removing the adhesive backing. Confirm alignment with the seat frame contours on both sides. Peel the protective film from the adhesive tape on the reverse of the cover. Align carefully and press firmly into position, applying sustained pressure across the full surface for 30–45 seconds. Repeat for the second cover on the opposite seat. Avoid adjusting the seat aggressively for at least one hour to allow the adhesive to cure fully. ⚠ Note: Do not attempt installation in temperatures below 10°C / 50°F as cold conditions significantly reduce initial adhesive bond strength. If fitted in winter, allow additional curing time before use. Complete Your Defender Interior Explore our full range of Defender 110 L663 interior accessories — designed for owners who hold their vehicle to a higher standard. Shop Defender 110 Collection Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 🚚 Worldwide Shipping via DHL, FedEx, UPS & TNT ↩ 30-Day Money-Back Guarantee 📞 +44 203 943 9919 Mon–Fri 9am–7pm Victorious Automotive is an independent retailer and is not affiliated with, endorsed by, or connected to Jaguar Land Rover Limited, Land Rover, or any of their subsidiaries. All vehicle names, model codes, and trademarks referenced are the property of their respective owners and are used solely for fitment identification purposes.

Victorious Automotive · Defender L663 · Interior Trim Dashboard Decoration Trim in Chrome & Carbon Fiber Texture — Land Rover Defender 90/110 (2020+) A precision-cut ABS trim panel finished in silver chrome or carbon fiber texture, designed to elevate the Defender L663 dashboard with a refined, sports-inspired aesthetic — no drilling, no cutting, no compromise. Defender L663 2020–2024 90 & 110 ABS Material Chrome Finish Carbon Fiber Texture ISO9001 Certified Adhesive Fit Model: LLK2806 Overview The 2020 Land Rover Defender L663 redefined what a modern off-road icon could look like — utilitarian in form, yet unmistakably contemporary on the inside. The dashboard, in particular, is a prominent focal point of the cabin, and for owners who want to push that interior feel a step further, the standard trim panels leave meaningful room for personalisation. This Dashboard Decoration Trim from Victorious Automotive is purpose-engineered for the Defender 90 and 110 (2020 onwards). Available in a polished silver chrome or a deep carbon fiber texture finish, the panel is precision-moulded from high-grade ABS to align exactly with the factory contours of the Defender dashboard — delivering a seamless, factory-quality result without any modification to your vehicle. Whether you're building a more urban-premium aesthetic with the chrome finish or leaning into a performance-inspired look with carbon fiber texture, this trim integrates naturally with the Defender's existing interior language. It's a small upgrade with a genuinely noticeable impact — the kind of detail that Defender owners notice immediately and appreciate for years. What's Included 🪄 Dashboard Decoration Trim 1x ABS trim panel — chrome or carbon fiber finish 🔧 Automotive Adhesive Tape Pre-cut 3M-style double-sided tape for clean fitment 📄 Installation Guide Step-by-step fitment reference included Product Highlights Precision-moulded ABS for exact Defender L663 dashboard fitment Available in silver chrome or carbon fiber texture finish Adhesive installation — no drilling, no permanent modification ISO9001-certified manufacturing for consistent quality standards Lightweight at 300g — no impact on cabin ergonomics Compatible with both Defender 90 and Defender 110 (2020+) Resistant to everyday cabin heat and UV exposure Matches factory interior trim lines for a seamless OEM look Reversible fitment — can be removed without damaging the dashboard Dimensions: 30cm (L) × 15cm (W) × 10cm (H) for ideal panel coverage Compatibility Vehicle Code Year Range Fitment Land Rover Defender 90 L663 2020–2024 Direct Fit Land Rover Defender 110 L663 2020–2024 Direct Fit Land Rover Defender 130 L663 2022–2024 Verify Before Purchase Land Rover Defender (Pre-2020) L316 Pre-2020 Not Compatible Range Rover Sport L494 / L461 All Years Not Compatible Range Rover Vogue L405 / L460 All Years Not Compatible Installation Notes Difficulty: Easy  ·  Estimated Time: 15–30 Minutes  ·  Tools Required: None Before beginning, ensure the Defender dashboard surface is clean and free from dust, grease, or moisture. A quick wipe with an isopropyl alcohol cloth is recommended for best adhesive performance. Dry-fit the trim panel against the dashboard to confirm alignment and verify the fitment before committing to installation. Peel back a small section of the adhesive tape backing, carefully align the panel to the dashboard contour, and press firmly from the centre outward to avoid air pockets. Remove the remaining tape backing as you press the panel fully into place, maintaining even pressure across the entire surface for 30–60 seconds. Allow the adhesive to cure at ambient cabin temperature for a minimum of 1–2 hours before exposing the vehicle to extreme heat or cold. ⚠ Note: While installation is straightforward for most owners, professional fitment is recommended if you are unfamiliar with automotive interior trim work. Ensure the vehicle interior is at room temperature before fitting — cold surfaces significantly reduce adhesive performance. Complete Your Defender Interior This trim pairs beautifully with our full range of Defender L663 interior accessories. Explore the complete collection and build the cabin your Defender deserves. Shop Defender L663 Accessories → Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 📦 Worldwide Shipping via DHL, FedEx, UPS & TNT ↩ 30-Day Money-Back Guarantee 📞 +44 203 943 9919 Mon–Fri, 9am–7pm Victorious Automotive is an independent aftermarket accessories retailer. This product is not manufactured by, affiliated with, or endorsed by Jaguar Land Rover Limited (JLR), Land Rover, or any of their subsidiaries. All vehicle model names, codes, and trademarks referenced are used solely for fitment identification purposes and remain the property of their respective owners. Please verify compatibility with your specific vehicle variant before purchase.

Victorious Automotive · Defender L663 · Interior Trim Land Rover Defender 110 Steering Wheel Trim Insert — Black / Oak Grain / Carbon Fiber (2020+) A precision-cut ABS steering wheel trim insert that brings a distinct, tailored finish to the Defender 110's cabin — available in three curated styles to complement any interior build. Defender L663 2020–2026 ABS Plastic Model: YW-1652 ISO9001 Certified Pre-Applied Adhesive Black / Oak Grain / Carbon Fiber 75g No-Drill Install Overview The 2020 Land Rover Defender L663 represented a complete reimagining of an icon — a vehicle that blends utilitarian heritage with genuinely modern interior design. The steering wheel sits at the centre of that experience, the point of contact between driver and machine on every journey. It deserves to look the part. This steering wheel trim insert (model YW-1652) is precision-cut from high-grade ABS plastic to slot flush into your Defender 110's steering wheel, filling the factory surround with a clean, refined finish. Choose from gloss Black for a stealthy, understated look, Oak Grain for a warmer, more distinguished character, or Carbon Fiber for a performance-forward aesthetic that pairs particularly well with darker cabin tones. Weighing just 75g and engineered with pre-applied adhesive backing, this is a trim upgrade that requires no tools, no drilling, and no specialist knowledge — just careful alignment and light pressure. ISO9001 manufacturing certification ensures the finish, fitment tolerances, and material quality are held to a consistent standard throughout production. What's Included 🎛️ Steering Wheel Trim Insert × 1 YW-1652 — available in Black, Oak Grain, or Carbon Fiber finish 🔖 Pre-Applied Adhesive Backing Factory-applied for a clean, no-mess install 📄 Installation Guide Step-by-step fitting instructions included Product Highlights Precision-cut ABS plastic for an exact, flush fitment on the Defender 110 steering wheel Three finish options — Black, Oak Grain, and Carbon Fiber — to suit every interior specification Pre-applied adhesive backing for a clean, tool-free installation ISO9001 certified manufacturing for consistent quality and finish tolerances Lightweight at just 75g — no impact on steering feel or airbag deployment clearance ABS plastic construction provides durability and resistance to everyday wear and heat Seamless OEM-style appearance that looks factory-fitted, not aftermarket Compatible with all trim levels of the 2020+ Defender 110 L663 No drilling, cutting, or permanent modification required Reversible upgrade — can be removed without damaging the original steering wheel Compatibility Vehicle Model Code Year Range Fitment Land Rover Defender 110 L663 2020–2026 Direct Fit Land Rover Defender 90 L663 2020–2026 Verify Before Purchase Land Rover Defender 130 L663 2022–2026 Verify Before Purchase Range Rover Sport L494 L494 2013–2022 Not Compatible Range Rover Vogue L405 L405 2013–2021 Not Compatible Range Rover Velar L560 L560 2018–2022 Not Compatible Installation Notes 🛠️ Difficulty: Easy  ·  Estimated Time: 10–15 minutes  ·  Tools Required: None Park your Defender 110 on a level surface and ensure the steering wheel is in its natural centre position before beginning. Clean the steering wheel trim surround thoroughly using an isopropyl alcohol wipe to remove any dust, oils, or residue. Allow to dry fully — this step is critical for adhesive bond quality. Dry-fit the trim insert without removing the adhesive backing to confirm alignment and fitment before committing to the final placement. Carefully peel back the protective film from the pre-applied adhesive layer, taking care not to touch the adhesive surface. Align the trim insert precisely with the steering wheel surround, starting from one edge and pressing firmly along the entire surface to ensure full contact and a bubble-free bond. Apply firm, even pressure across the full length of the insert and hold for 30–60 seconds to activate the adhesive. Allow a minimum of 2 hours before driving to allow the adhesive to fully cure before the trim experiences vibration or movement. ⚠ Important: Do not install in temperatures below 10°C (50°F) as this can significantly reduce adhesive bond strength. Avoid cleaning the area with silicone-based products prior to installation. Always verify your exact vehicle model and year against the compatibility table before purchase — steering wheel designs can vary between trim levels and model years. Complete Your Defender Interior This steering wheel trim is just the start. Explore our full range of Defender L663 interior upgrades — from dashboard trim panels to gear surround inserts — all precision-engineered to the same standard. Shop Defender 110 Accessories Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 📦 Worldwide Shipping via DHL, FedEx, UPS & TNT ↩️ 30-Day Money-Back Guarantee 📞 +44 203 943 9919 Mon–Fri, 9am–7pm Victorious Automotive is an independent aftermarket accessory retailer. This product is not manufactured by, affiliated with, endorsed by, or approved by Land Rover, Jaguar Land Rover (JLR), or any of their subsidiaries. All vehicle names, model codes, and trademarks referenced are the property of their respective owners and are used solely for the purpose of identifying product compatibility. Always verify fitment with your specific vehicle model and year before purchase.

Victorious Automotive · Defender L663 · Interior Trim Black ABS Steering Wheel Trim for Land Rover Defender L663 110 (2020–2026) A precision-engineered ABS steering wheel trim that instantly elevates the cockpit of your Defender L663 with a clean, blacked-out finish — no tools, no fuss. Defender L663 2020–2026 110 Wheelbase High-Grade ABS Gloss Black Peel & Stick Interior Trim Direct Fit Overview The Defender L663 110 represents Land Rover's boldest reinterpretation of an icon — a vehicle that blends serious off-road capability with a cabin that's increasingly expected to meet modern luxury standards. For owners who want every detail of their interior to reflect that ambition, the steering wheel is one of the most tactile touchpoints in the entire cabin and one of the first places where a considered upgrade makes an immediate difference. This black ABS steering wheel trim is designed from the ground up to suit the specific geometry of the L663's steering wheel, sitting flush against the existing surfaces without gaps, overhang, or misalignment. Moulded from high-grade ABS thermoplastic, it delivers a consistently matte-black or gloss-black aesthetic that complements the Defender's utilitarian-premium design language — whether your vehicle is trimmed in Ebony, Kvadrat, or the standard cloth finish. The installation method is intentionally simple: a clean peel-and-stick adhesive system means no drilling, no harness interference, and no risk to your vehicle's electronics or airbag system. It's the kind of upgrade that takes minutes but looks like it came from the factory — exactly what a well-specced Defender deserves. What's Included 🖤 Steering Wheel Trim × 1 Black ABS, pre-shaped for L663 steering wheel 🔧 Pre-Applied Adhesive High-bond 3M-grade backing tape included 🧹 Cleaning Prep Wipe For surface preparation before fitment 📄 Fitment Guide Step-by-step printed installation instructions Product Highlights Precision-moulded to match the exact profile of the L663 Defender steering wheel High-grade ABS construction — resistant to heat, UV exposure, and everyday wear Gloss black finish complements both dark and light interior colour schemes Tool-free peel-and-stick installation — no removal of steering wheel required Does not interfere with airbag deployment, buttons, or paddle shifters Lightweight design adds no perceptible weight or bulk to the wheel Colour-stable finish — resists fading and yellowing over time 100% brand new — not refurbished or remanufactured Easy to remove cleanly without leaving residue if needed Ships worldwide via DHL, FedEx, UPS, or TNT — tracked and insured Compatibility Vehicle Code Year Range Fitment Land Rover Defender 110 L663 2020–2026 Direct Fit Land Rover Defender 90 L663 2020–2026 Verify Before Purchase Land Rover Defender 130 L663 2022–2026 Verify Before Purchase Range Rover Sport L494 / L461 2013–2026 Not Compatible Range Rover Vogue L405 / L460 2013–2026 Not Compatible Range Rover Velar L560 2018–2022 Not Compatible Installation Notes Difficulty: Easy  ·  Estimated Time: 10–15 minutes  ·  Tools Required: None Park your Defender on a level surface with the engine off. Ensure the steering wheel is in its default centre position. Use the included prep wipe to thoroughly clean the area of the steering wheel where the trim will be applied. Allow to dry completely — at least 2 minutes. Dry-fit the ABS trim piece against the steering wheel to confirm alignment and orientation before committing to adhesion. Peel back the adhesive backing film gradually as you position and press the trim firmly onto the steering wheel surface. Work from one end to the other to avoid air bubbles. Apply firm, even pressure across the entire trim piece for 30–60 seconds to fully activate the adhesive bond. Allow a minimum of 2 hours before driving to let the adhesive cure fully, particularly in cooler ambient temperatures. ⚠ Important: Do not attempt to install this trim while the engine is running or the vehicle is in motion. This trim is designed for the steering wheel surround only — keep clear of all airbag cover seams, controls, and horn pad areas. If you are unsure of any stage, contact our support team on +44 203 943 9919 before proceeding. Complete Your Defender Interior Thousands of Defender owners have trusted Victorious Automotive to deliver premium trim upgrades that look factory-fitted and last. Browse the full Defender L663 interior collection and finish what you started. Shop Defender L663 Accessories → Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 📦 Worldwide Shipping via DHL, FedEx, UPS & TNT 🔄 30-Day Money-Back Guarantee 📞 Mon–Fri 9am–7pm · +44 203 943 9919 Victorious Automotive is an independent aftermarket retailer and is not affiliated with, endorsed by, or connected to Land Rover, Jaguar Land Rover (JLR), or any of their subsidiaries. All vehicle names, model codes, and trademarks referenced on this page are used solely for fitment identification purposes and remain the intellectual property of their respective owners. Product imagery is for illustrative purposes only — always verify compatibility with your specific vehicle variant before purchase.

Victorious Automotive · Defender L663 · Interior Trim Right-Hand Drive ABS Plastic Window Lift Switch Buttons Frame Cover for Land Rover Defender 110 (2020+) A precision-cut ABS trim cover that upgrades the window switch panel on your Defender 110, available in four finishes to complement any interior style. Defender L663 2020–2026 Right-Hand Drive ABS Plastic ISO9001 Certified 4 Colour Options Adhesive Fit Interior Trim No Drilling Model LLK2782 Overview The 2020 Land Rover Defender L663 redefined the nameplate — sharper lines, a more driver-focused cabin, and a degree of modernity that the original series never attempted. But even on a vehicle at this price point, the stock interior trim leaves room for personalisation. The window switch panel is one of the most frequently touched surfaces in the cabin, and it's one of the first areas where owners look to introduce a finish that better reflects their taste. This Window Lift Switch Buttons Frame Cover is engineered specifically for right-hand drive Defender 110 models from 2020 onwards. Manufactured from high-grade ABS plastic certified to ISO9001 standards, it wraps cleanly around the existing switch housing without modification to the vehicle's wiring or switchgear. The cover installs using pre-applied automotive adhesive tape, forming a solid bond to the factory trim beneath. Available in four distinct finishes — Gloss Black, Oak Wood Grain, Silver, and Carbon Fiber — this cover allows you to tailor the interior character of your Defender from understated to boldly accented. Whether you're building a clean all-black cockpit or layering in warm wood tones for a more expedition-touring feel, this is a low-effort, high-impact upgrade that makes an immediate difference to the way the cabin presents itself. What's Included 🪟 Window Switch Frame Cover × 1 ABS plastic, pre-cut for RHD Defender 110 (2020+) 🔲 Adhesive Tape Pre-Applied Automotive-grade 3M-style backing tape included on reverse 📋 Installation Guide Step-by-step fitting instructions included in packaging Product Highlights Precision-cut ABS plastic for a seamless OEM-style fit over the factory switch housing Right-hand drive specific — designed exclusively for RHD Defender 110 2020 models Available in four finishes: Gloss Black, Oak Wood Grain, Silver, and Carbon Fiber ISO9001 certified manufacturing — consistent quality and dimensional accuracy guaranteed Adhesive tape installation — no drilling, no cutting, no damage to the vehicle Lightweight at 200g — no added bulk or interference with switch operation Compact profile: 30cm × 15cm × 10cm — sits flush with surrounding trim surfaces Durable ABS construction resists UV fading, daily wear, and temperature fluctuation Reversible upgrade — can be removed and replaced without permanent alteration An immediate visual upgrade to one of the cabin's most frequently interacted surfaces Compatibility Vehicle Code Year Range Drive Side Fitment Land Rover Defender 110 L663 2020–2026 Right-Hand Drive Direct Fit Land Rover Defender 90 L663 2020–2026 Right-Hand Drive Verify Before Purchase Land Rover Defender 130 L663 2022–2026 Right-Hand Drive Verify Before Purchase Land Rover Defender 110 L663 2020–2026 Left-Hand Drive Not Compatible Land Rover Defender (Pre-2020) Classic Pre-2020 All Not Compatible Range Rover Sport L494 / L461 All All Not Compatible Range Rover Vogue L405 / L460 All All Not Compatible Installation Notes Difficulty: Easy  ·  Estimated Time: 15–25 Minutes  ·  Tools Required: None Park the vehicle on a level surface and ensure the interior is at a stable temperature — avoid fitting in direct sunlight or extreme cold, as this affects adhesive performance. Thoroughly clean the existing window switch panel surround using an isopropyl alcohol wipe or a clean microfibre cloth. Allow to dry completely before proceeding. Dry-fit the frame cover over the switch housing to confirm alignment and positioning before committing. Check that all switch cutouts align precisely with the factory buttons. Peel the protective film from the pre-applied adhesive tape on the reverse of the cover, taking care not to touch the adhesive surface. Align the cover carefully with the switch housing, then press firmly and evenly across the entire surface for 30–60 seconds to activate the adhesive bond. Allow 24 hours for the adhesive to fully cure before applying pressure to the switch area or wiping the surface down. ⚠ Important: This cover is designed for right-hand drive Defender 110 (2020+) only. Verify your vehicle's drive configuration and model year before installation. Incorrect fitting on an incompatible vehicle may result in misalignment or interference with switch operation. If in doubt, contact our team on +44 203 943 9919 before purchase. Complete Your Defender Interior Join over 12,300 Land Rover and Defender owners who trust Victorious Automotive for interior upgrades that actually fit, finish properly, and last. Browse the full Defender L663 collection for matching trim pieces and cabin accessories. Shop Defender 110 (2020+) Collection Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 Stars · 12,300+ Verified Reviews 🔄 30-Day Money-Back Guarantee 🌍 Worldwide Shipping via DHL, FedEx, UPS & TNT 📞 +44 203 943 9919 · Mon–Fri 9am–7pm Victorious Automotive is an independent aftermarket accessory retailer. This product is not manufactured by, affiliated with, endorsed by, or approved by Land Rover, Jaguar Land Rover (JLR), or any of their subsidiaries. All vehicle names, model codes, and trademarks referenced are the property of their respective owners and are used solely for fitment identification purposes. Always verify compatibility with your specific vehicle before purchase.

Victorious Automotive · Defender L663 · Interior Trim Oak Wood Grain ABS Window Lifter Switch Trim – Left-Hand Drive Defender 110 (2020+) A precision-fitted interior trim panel that brings warm, natural oak wood grain texture to the door switch surround of your 2020+ Land Rover Defender 110 or 130 — no drilling, no modification, just a refined finish. Defender L663 2020–2026 Left-Hand Drive Oak Wood Grain ABS Material Window Lifter Trim ISO9001 Certified Adhesive Fit Model: XYL1596 Overview The 2020 Land Rover Defender L663 was engineered as a capable, forward-thinking reinterpretation of an icon — and its interior reflects that ambition. The cabin is clean, purposeful, and increasingly being personalised by owners who want to move beyond the factory-standard black plastics and inject a sense of warmth and character into their daily environment. This Oak Wood Grain Window Lifter Switch Trim is designed specifically for the door panel of the Defender 110 and 130. Manufactured in durable ABS with a convincing oak wood grain surface finish, the trim wraps the inner window lifter switch area with a material that reads as premium without being ostentatious — a natural complement to the Defender's earthy, adventure-ready aesthetic. Installation requires no specialist tools and no permanent modification to your vehicle. A pre-applied automotive-grade adhesive backing bonds the trim cleanly to the factory surface, making it a reversible, weekend-friendly upgrade that delivers a visually significant result. If you're building out a fully personalised Defender interior, this piece ties in seamlessly with other wood grain or dark accent trim options across the cabin. What's Included 🪵 Window Lifter Switch Trim 1 × Oak wood grain ABS trim panel — LHD fitment 🔧 Pre-Applied Adhesive Automotive-grade 3M-style tape pre-installed on reverse 📦 Protective Packaging Individual protective wrap to prevent transit damage Product Highlights Precision-cut to match the Defender 110 / 130 door panel profile exactly Oak wood grain ABS finish — warm, natural tone with consistent grain texture Manufactured to ISO9001 quality standards for consistent production quality Durable ABS construction resists warping, cracking, and UV discolouration Pre-applied automotive adhesive tape — no drilling or permanent fixing required Left-hand drive specific — correct switch layout alignment for LHD vehicles Lightweight at 148g — no added bulk or rattle risk to the door panel Compatible with both Defender 110 and Defender 130 body variants Clean, reversible installation — removable without damage to OEM panels Pairs naturally with other oak wood grain interior trim pieces across the cabin Compatibility Vehicle Year Range Drive Body Fitment Land Rover Defender L663 2020–2026 Left-Hand Drive 110 Direct Fit Land Rover Defender L663 2020–2026 Left-Hand Drive 130 Direct Fit Land Rover Defender L663 2020–2026 Right-Hand Drive 110 / 130 Not Compatible Land Rover Defender L663 2020–2026 Left-Hand Drive 90 Not Compatible Land Rover Defender (Pre-2020) Pre-2020 All All Not Compatible Range Rover / Discovery / Other All All All Not Compatible Installation Notes 🛠 Difficulty: Easy  ·  Estimated Time: 10–15 Minutes  ·  Tools Required: None Begin with the vehicle parked, interior lighting on. Ensure the door panel and window switch surround area are at room temperature — cold surfaces reduce adhesive performance. Thoroughly clean the target surface using an isopropyl alcohol wipe or similar degreasing agent. Remove any dust, oil, or residue. Allow to dry completely before proceeding. Dry-fit the trim panel over the window lifter switch surround to confirm alignment and check that all edges sit flush against the factory panel before committing. Peel back the adhesive liner from the reverse of the trim, starting from one corner. Take care not to touch the adhesive surface with bare fingers. Position the trim carefully from one end, pressing down firmly as you work across the full length. Apply sustained pressure for 30–60 seconds across the entire surface to fully activate the adhesive bond. Allow the adhesive to cure for a minimum of 24 hours before operating the window switches vigorously or exposing the trim to moisture or temperature extremes. ⚠ Important: This trim is designed for Left-Hand Drive vehicles only. Installing on a Right-Hand Drive Defender will result in misaligned switch cutouts. If you are unsure of your vehicle's drive configuration, check the position of the steering wheel — LHD vehicles have the steering wheel on the left side of the cabin. Upgrade Your Defender Interior Browse our full collection of Defender L663 interior trim accessories — from dashboard surrounds to gear selector frames — all engineered for the 2020–2026 platform. Shop Defender L663 Interior → Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 🔄 30-Day money-back guarantee ✈️ Worldwide shipping via DHL, FedEx, UPS & TNT 📞 +44 203 943 9919 Mon–Fri, 9am–7pm Victorious Automotive is an independent retailer of aftermarket and compatible accessories for Land Rover and Jaguar Land Rover vehicles. This product is not manufactured by, endorsed by, or affiliated with Jaguar Land Rover Limited, Land Rover, or any of their subsidiaries. All vehicle names, model codes, and trademarks referenced are the property of their respective owners and are used solely for fitment identification purposes.

Victorious Automotive · Defender L663 · Interior Trim Right-Hand Drive ABS Black Grain Inner Window Lifter Switch Trim for Land Rover Defender 110 & 130 (2020+) A precision-fitted RHD door switch surround in textured black ABS grain — purpose-built to slot seamlessly into the Defender L663's interior and elevate the tactile quality of every interaction. Defender L663 2020–2026 Right-Hand Drive ABS Material Black Grain Finish Window Switch Trim ISO9001 Certified No Drilling Required Overview The Land Rover Defender 110 L663 redefined what a modern Defender could be — combining authentic off-road capability with a significantly more refined interior than its predecessors. For owners who want their Defender's cabin to reflect that same level of intention, the details matter. The window lifter switch surrounds are among the most frequently touched surfaces inside the vehicle, and upgrading them is one of the most impactful ways to sharpen the interior's overall feel. This window lifter switch trim is engineered specifically for right-hand drive variants of the Defender 110 and 130 (2020 onwards). Constructed from high-grade ABS with a textured black grain finish, it mirrors the factory aesthetic while introducing a noticeably more refined surface quality. Every dimension — 29cm in length, 12cm wide, 4cm in height — has been matched precisely to the OEM switch panel footprint, ensuring a flush, factory-correct fit without modification. Installation is straightforward and tool-free. Pre-applied automotive-grade adhesive tape is included, providing a secure, vibration-resistant bond that holds firm across the full spectrum of Defender use — whether you're navigating city streets or heading off the beaten track. Backed by ISO9001 manufacturing certification, this trim delivers the kind of quality you'd expect from a brand that takes Defender ownership seriously. What's Included 🪟 Window Lifter Switch Trim 1x RHD ABS Black Grain panel, pre-cut to OEM dimensions 🔧 Automotive Adhesive Tape Pre-applied, high-bond 3M-grade tape for tool-free fitment 📄 Installation Guide Step-by-step fitting instructions included in packaging Product Highlights Designed exclusively for RHD Defender 110 & 130 L663 from 2020 onwards Textured black ABS grain finish matches the Defender's factory interior language Precisely dimensioned at 29cm × 12cm × 4cm for a seamless OEM-style fit Weighs just 148g — no structural modification or added bulk ISO9001 certified manufacturing for consistent quality and durability Tool-free installation via included automotive-grade adhesive tape ABS construction is heat-resistant and resistant to surface cracking over time Enhances the tactile quality of the most frequently touched interior surface Compatible with all trim levels of the Defender 110 and 130 (2020+) in RHD spec No wiring, no cutting, no permanent modification to the vehicle required Compatibility Model Year Range Drive Side Trim Level Fitment Defender 110 L663 2020–2026 Right-Hand Drive All Variants Direct Fit Defender 130 L663 2020–2026 Right-Hand Drive All Variants Direct Fit Defender 90 L663 2020–2026 Right-Hand Drive All Variants Verify Before Purchase Defender 110 L663 2020–2026 Left-Hand Drive All Variants Not Compatible Defender 130 L663 2020–2026 Left-Hand Drive All Variants Not Compatible Classic Defender (Pre-2020) Pre-2020 Any Any Not Compatible Installation Notes 🛠 Difficulty: Easy  ·  ⏱ Estimated Time: 15–20 Minutes  ·  🔩 Tools Required: None Begin with the vehicle parked and the interior temperature at room level. Avoid installation in very cold conditions as adhesive bond strength may be reduced. Thoroughly clean the existing window switch surround area using an isopropyl alcohol (IPA) wipe or equivalent. Remove all dust, oil, and residue from the surface. Allow to dry completely — this is the most important step for long-term adhesion. Dry-fit the trim panel against the switch surround to confirm alignment and fitment before committing. Check that all edges sit flush and the switch apertures line up correctly. Peel the protective backing from the pre-applied automotive adhesive tape on the reverse of the trim panel. Carefully position the trim panel over the switch surround, aligning from one edge and pressing down progressively to avoid trapping air bubbles beneath the panel. Apply firm, even pressure across the entire surface for 30–60 seconds to activate the adhesive bond. Pay particular attention to the corners and edges. Allow the adhesive to cure for a minimum of 24 hours before subjecting the trim to any stress or heavy use. ⚠ Important: This trim is designed specifically for right-hand drive vehicles. Installing on a left-hand drive Defender will result in incorrect alignment. If you are unsure of your vehicle's specification, please contact us before ordering on +44 203 943 9919 (Mon–Fri, 9am–7pm). Complete Your Defender Interior This switch trim is just the beginning. Explore our full Defender L663 interior collection — from door handle surrounds to dashboard trim panels — and build a cabin that's entirely your own. Shop Defender L663 Interior → Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 🔄 30-Day money-back guarantee 🌍 Worldwide shipping via DHL, FedEx, UPS & TNT 📞 Expert support Mon–Fri, 9am–7pm Victorious Automotive is an independent aftermarket accessories retailer. We are not affiliated with, endorsed by, or connected to Land Rover, Jaguar Land Rover (JLR), or any of their subsidiaries. All vehicle names, model codes, and trademarks referenced are the property of their respective owners and are used solely for fitment identification purposes.

Victorious Automotive · Defender L663 · Interior Trim Silver Aluminium Speaker Cover Set for 2020 Land Rover Defender L663 A precision-cut set of eight aluminium alloy speaker covers engineered to integrate seamlessly into the 2020 Defender's interior — elevating the cabin's tone with a brushed silver finish that feels factory-intentional. Defender L663 2020 Aluminium Alloy Silver Finish Set of 8 Adhesive Fit Interior Trim ISO9001 Certified Overview The 2020 Land Rover Defender L663 marked a defining moment for the nameplate — a thoroughly modern reinterpretation of an icon, with a cabin that balances rugged utility and refined detail in equal measure. Owners who appreciate that balance understand that every surface inside the Defender tells a story, and the speaker grilles are no exception. Left in their standard finish, they can feel like a missed opportunity. Upgraded, they become a quiet statement of intent. This Silver Speaker Cover Set has been developed specifically for the 2020 Defender, with each of the eight pieces precision-cut from aircraft-grade aluminium alloy and finished in a cool brushed silver that complements the Defender's existing interior colour palette. The result is a cohesive, upscaled look that reads as premium without ever feeling overdone — the kind of upgrade that makes you notice it immediately on installation, then forget it was ever any other way. Installation requires no specialist tools and no permanent modification to the vehicle. Each cover arrives with pre-applied automotive-grade adhesive tape, allowing a clean, confident bond to the existing speaker surrounds in a matter of minutes. Whether you drive a daily Defender 90 or a weekend Defender 110, this set delivers a tangible interior improvement that punches well above its price point. What's Included 🔊 Speaker Covers × 8 Full set — front and rear positions covered 🔖 Pre-Applied Adhesive Tape Automotive-grade, heat-resistant bond included on each piece 📋 Installation Guide Step-by-step instructions for a clean, confident fit 📦 Protective Packaging Each cover individually protected to prevent transit damage Product Highlights Designed exclusively for the 2020 Land Rover Defender L663 interior Brushed silver aluminium alloy — premium material, lasting finish Set of 8 covers for comprehensive interior coverage Pre-applied automotive adhesive — no drilling, no damage ISO9001 certified manufacturing for consistent quality Lightweight construction — no added bulk or vibration risk Corrosion-resistant finish suited to varied climates Refined silver tone complements both dark and light Defender cabins Direct-fit design — no trimming or modification required Reversible install — leaves no lasting marks on OEM trim Compatibility Model Code Year Range Fit Land Rover Defender 90 L663 2020 Direct Fit Land Rover Defender 110 L663 2020 Direct Fit Land Rover Defender 130 L663 2020 Direct Fit Range Rover Sport L494 2013–2020 Not Compatible Range Rover Vogue L405 2013–2020 Not Compatible Range Rover Velar L560 2018–2022 Not Compatible Range Rover Sport L461 2022–2026 Not Compatible Range Rover Vogue L460 2022–2026 Not Compatible Installation Notes 🛠 Difficulty: Easy  ·  ⏱ Estimated Time: 20–30 Minutes  ·  🔧 Tools Required: None Begin with a clean, dry interior. Remove any dust or grease from the existing speaker surrounds using an isopropyl alcohol wipe — this is the single most important step for a lasting bond. Allow the cleaned surfaces to dry completely for at least 2–3 minutes before proceeding. Dry-fit each cover to its corresponding speaker surround to confirm position and orientation before committing to adhesion. Peel back the protective film from the pre-applied adhesive tape on the first cover, aligning it carefully with the speaker surround before pressing into place. Apply firm, even pressure across the full surface of each cover for 30–60 seconds to activate the adhesive bond. Repeat for all remaining covers, working systematically around the cabin. Allow the adhesive to fully cure for a minimum of 24 hours before exposing the covers to moisture or extreme temperatures. ⚠ Note: Avoid installation in temperatures below 10°C — cold surfaces significantly reduce the initial adhesive bond strength. If your Defender has been stored in a cold garage, allow the interior to warm up to ambient room temperature before fitting. Complete Your Defender's Interior This speaker cover set is just one piece of a wider interior transformation. Explore our full range of Defender L663 accessories — from dashboard trim to door handle covers — all curated specifically for the 2020 Defender. Shop All Defender L663 Accessories Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 🔄 30-Day money-back guarantee ✈️ Worldwide shipping via DHL, FedEx, UPS & TNT 📞 +44 203 943 9919 Mon–Fri, 9am–7pm Victorious Automotive is an independent aftermarket accessories retailer. We are not affiliated with, endorsed by, or connected to Land Rover, Jaguar Land Rover (JLR), or any of their subsidiaries. All brand names, vehicle model names, and codes referenced are used solely for the purpose of fitment identification. Product model: LLK2816. Dimensions: 30cm (L) × 15cm (W) × 10cm (H). Weight: 300g. Certification: ISO9001.

Victorious Automotive · Defender L663 · Interior Trim Aluminum Alloy Door Screw Protection Covers for Land Rover Defender 110/130 L663 (2020–2021) — Red & Silver Transform exposed interior screw heads into purposeful, precision-finished accents — purpose-engineered for the Defender 110 and 130 in anodised red or brushed silver aluminium alloy. Defender L663 2020–2021 Aluminum Alloy Interior Trim Door Screw Covers Red / Silver No-Drill Fit ISO9001 Certified Model: LLK2918 Overview The Land Rover Defender L663 was designed to be honest about its construction — rugged, purposeful, and unapologetically mechanical. But exposed screw heads throughout the cabin door panels are one area where the factory finish leaves something to be desired. For owners who take pride in every detail of their Defender's interior, those raw fixings stand out for the wrong reasons. These Aluminum Alloy Door Screw Protection Covers are machined to sit flush over each exposed screw head, converting utilitarian fixings into deliberate, styled accents. Available in a bold anodised red or a refined brushed silver, they complement both stock and upgraded Defender interiors — whether you're running a fully specced First Edition or a stripped-back commercial variant you've personalised from the ground up. Constructed from durable aluminium alloy and certified to ISO9001 quality standards, these covers are engineered for longevity. The pre-applied automotive-grade adhesive backing means no drilling, no cutting, and no modification to your vehicle — just a clean, considered finish that looks like it came straight from the factory. What's Included 🔩 Option 1 — Set of 11 Covers Ideal for targeted door panel coverage on a single area 🔩 Option 2 — Set of 56 Covers Full interior coverage across all door panels and trim points 🏷️ Pre-Applied Adhesive Backing Automotive-grade tape included on each cover, ready to fit 📦 Protective Packaging Each set securely packaged to prevent transit damage Product Highlights Conceals exposed factory screw heads for a cleaner, more finished interior appearance Precision-machined aluminium alloy construction — lightweight yet exceptionally durable Available in anodised red or brushed silver to suit your interior colour scheme Pre-applied automotive-grade adhesive for a secure, no-drill installation ISO9001 certified manufacturing — consistent quality across every unit Fitment-specific design for Defender 110 and 130 L663 (2020–2021 model years) Two set sizes available — 11-piece for targeted areas or 56-piece for full coverage Low-profile fit that sits flush with surrounding trim panels without protruding Resistant to vibration, heat, and the rigours of daily Defender use Reversible installation — covers can be removed without damage to original trim Compatibility Vehicle Code Years Fitment Land Rover Defender 110 L663 2020–2021 Direct Fit Land Rover Defender 130 L663 2020–2021 Direct Fit Land Rover Defender 90 L663 2020–2021 Unconfirmed Land Rover Defender 110/130 L663 2022–2026 Unconfirmed Range Rover Sport L494 / L461 All Years Not Compatible Range Rover Vogue L405 / L460 All Years Not Compatible Range Rover Velar L560 All Years Not Compatible Installation Notes 🛠 Difficulty: Easy  ·  ⏱ Estimated Time: 15–30 minutes  ·  🔧 Tools Required: None Thoroughly clean the area around each exposed screw head using an isopropyl alcohol wipe. Remove any dust, grease, or residue to ensure maximum adhesive bond. Allow the cleaned surfaces to dry completely before proceeding — approximately 2–3 minutes in normal conditions. Peel the protective film from the adhesive backing on the first cover, taking care not to touch the adhesive surface. Align the cover precisely over the screw head, ensuring it sits centrally and flush with the surrounding trim panel. Apply firm, even pressure for 20–30 seconds to activate the adhesive bond fully. Repeat across all remaining screw positions. For the 56-piece set, work systematically across each door panel in sequence to ensure consistent alignment. Allow 24 hours before exposing the covers to extreme heat or moisture for a fully cured bond. ⚠ Note: Colour may vary slightly from product imagery due to differences in screen calibration. We recommend ordering a sample or reviewing both colour options carefully before committing to a full 56-piece set. Do not apply to wet, dirty, or freshly cleaned surfaces that have not been allowed to dry. Finish Your Defender the Right Way Every detail matters when it comes to your L663. Browse our full range of Defender interior accessories and give your cabin the precision finish it deserves. Shop All Defender L663 Accessories Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 🔄 30-Day money-back guarantee 🌍 Worldwide shipping via DHL, FedEx, UPS & TNT 📞 +44 203 943 9919 Mon–Fri, 9am–7pm Victorious Automotive is an independent aftermarket accessory retailer. This product is not manufactured by, affiliated with, or endorsed by Land Rover, Jaguar Land Rover (JLR), or any of their subsidiaries. All vehicle names, model codes, and trademarks referenced are used for fitment identification purposes only and remain the property of their respective owners.

Victorious Automotive · Defender L663 · Interior Trim ABS Carbon Fiber Seat Back USB Port Panel Frame for Land Rover Defender 110 (2020–2026) L663 A precision-fit carbon fibre panel overlay that brings a sharper, more customised presence to the Defender 110's rear seat USB port surrounds — no drilling, no compromise. Defender L663 2020–2026 ABS Carbon Fibre Direct Fit Interior Trim USB Port Panel Seat Back Adhesive Install No Drilling Overview The Land Rover Defender 110 L663 redefined what a modern off-road icon could look like — and owners who've invested in one know that every detail matters. The interior, while thoughtfully designed from the factory, offers genuine scope for personalisation, particularly in areas like the rear seat panel surrounds where OEM plastics can look understated relative to the rest of the cabin's character. This seat back USB port panel frame is engineered specifically for the 2020-onward Defender 110 L663. Constructed from high-grade ABS with a precision-applied carbon fibre finish, it overlays the existing USB port surround panels on the rear seat backs with a clean, textured look that adds depth and visual contrast. The result is a subtle but immediately noticeable upgrade — exactly the kind of refinement that discerning Defender owners appreciate. Fitment is handled through pre-applied automotive-grade adhesive tape, meaning the installation process is clean, reversible if needed, and requires no specialist tools. Whether you're building out a fully kitted interior or simply adding considered finishing touches, this panel is a low-effort, high-impact addition to your L663's cabin. What's Included 🪑 Seat Back USB Panel Frame × 2 Carbon fibre finish ABS overlays, one per seat back position 🔧 Pre-Applied Adhesive Tape Automotive-grade 3M-style tape, factory-applied to each panel 📋 Installation Guidance Basic fitting instructions included with each order Product Highlights Precision-engineered to fit the Defender 110 L663 seat back USB port surround exactly High-quality ABS substrate with durable carbon fibre texture finish Lightweight construction — adds zero meaningful weight to the interior Pre-applied automotive adhesive tape for a clean, tool-free installation Retains full access and functionality of the USB ports beneath Resistant to UV fading and everyday interior wear and abrasion Adds visual contrast and a premium carbon accent to the rear cabin No permanent modification — fully reversible installation method Ships as a matched pair for left and right seat back positions Compatible across all trim levels of the 2020–2026 Defender 110 L663 Compatibility Model Code Year Range Trim Level Fitment Defender 110 L663 2020–2026 Standard / S / SE Direct Fit Defender 110 L663 2020–2026 HSE / X / X-Dynamic Direct Fit Defender 110 L663 2020–2026 First Edition / 75th Anniversary Direct Fit Defender 90 L663 2020–2026 All Trims Verify Before Purchase Defender 130 L663 2022–2026 All Trims Verify Before Purchase Range Rover Sport L461 / L494 All Years All Trims Not Compatible Range Rover Vogue L460 / L405 All Years All Trims Not Compatible Installation Notes 🛠 Difficulty: Easy  ·  Estimated Time: 10–15 Minutes  ·  Tools Required: None Begin with the vehicle parked and the interior at or above room temperature — cold surfaces can reduce adhesive bond strength significantly. Fold the rear seat forward or gain clear access to the seat back USB port panels you intend to trim. Using a clean microfibre cloth and isopropyl alcohol (IPA), thoroughly clean the plastic surface around the USB port surrounds. Remove any dust, oils, or residue and allow to dry completely for at least 2–3 minutes. Dry-fit each panel frame against the USB port surround to confirm alignment and orientation before committing. Note the correct position carefully. Peel the protective backing from the pre-applied adhesive tape on the first panel frame. Align the panel carefully over the USB port surround and press firmly into place, applying even pressure across the full surface for 30–60 seconds. Repeat for the second panel frame on the opposing seat back. Allow a minimum of 24 hours before exposing the panels to sustained pressure or cleaning products to allow the adhesive to fully cure. ⚠ Important: Do not attempt installation on a cold or damp surface. Adhesive performance is significantly reduced below 15°C (59°F). If removing panels in future, use a plastic trim pry tool and apply gentle heat with a heat gun or hairdryer to release the adhesive without marking the underlying trim. Complete Your Defender 110 Interior Browse our full range of precision-fit interior accessories designed exclusively for the Defender L663 — from dashboard trim overlays to door panel accents and centre console upgrades. Shop Defender L663 Accessories → Use code 22GET20 for 20% off when you buy any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 📦 Worldwide Shipping via DHL, FedEx, UPS & TNT 🔁 30-Day Money-Back Guarantee 📞 +44 203 943 9919 Mon–Fri, 9am–7pm Victorious Automotive is an independent aftermarket accessory retailer. This product is not manufactured by, endorsed by, or affiliated with Land Rover, Jaguar Land Rover (JLR), or any of their subsidiaries. All vehicle names, model codes, and trademarks referenced are used for fitment identification purposes only and remain the property of their respective owners. Always verify compatibility with your specific vehicle configuration before purchase. If in doubt, contact our team before ordering.

Victorious Automotive · Defender L663 · Interior Trim Aluminum Alloy Dashboard Speaker Net Cover Sticker for Land Rover Defender 110 (2020) – Interior Modification A precision-engineered aluminum alloy speaker grille cover that elevates the Defender 110's dashboard with a refined, factory-quality finish — no drilling, no mess, no compromise. Defender L663 2020 Model Year Aluminum Alloy Peel & Stick Dashboard Trim Speaker Protection ISO9001 Certified Interior Mod Overview The 2020 Land Rover Defender 110 arrived as a modern reinterpretation of an icon — built tough but designed to impress. Its interior strikes a deliberate balance between utility and sophistication, and for owners who want to push that balance further, every detail matters. The dashboard speaker area, functional as it is, benefits enormously from a considered upgrade — and that's exactly where this cover steps in. Crafted from high-grade aluminum alloy and finished in a sleek matte black, this dashboard speaker net cover sticker is designed as a direct-fit solution for the 2020 Defender 110. It sits flush over the existing speaker grille, adding a layer of visual refinement and physical protection that feels entirely at home with the Defender's industrial-meets-premium aesthetic. The precision-cut net pattern mirrors the quality you'd expect from a factory-fitted accessory. Installation requires no tools and no specialist knowledge. The cover is backed with automotive-grade adhesive tape that bonds securely to the dashboard surface, creating a stable, rattle-free fit. It's the kind of upgrade that's subtle enough to look original, but significant enough that anyone who knows the Defender will notice — and appreciate — the difference. What's Included 🔲 Dashboard Speaker Net Cover 1× aluminum alloy sticker panel, matte black finish 🔗 Pre-Applied Adhesive Tape Automotive-grade, heat-resistant bonding layer 📋 Installation Guide Step-by-step fitment instructions included Product Highlights Precision-engineered for a direct fit on the 2020 Defender 110 dashboard High-grade aluminum alloy construction — durable, lightweight, corrosion-resistant Sleek matte black finish complements all Defender interior colour schemes Automotive-grade peel-and-stick adhesive — no drilling or modification required Speaker net pattern provides physical protection without affecting sound quality ISO9001 certified manufacturing — consistent quality across every unit Rattle-free installation when applied to a clean, dry surface Heat and humidity resistant — built for real-world driving conditions Subtle, OEM-inspired aesthetic that doesn't disrupt the factory interior look Reversible modification — can be removed without damage to the dashboard surface Specifications Specification Detail Material Aluminum Alloy Finish Matte Black Dimensions 35cm (L) × 25cm (W) × 10cm (H) Weight 300g Fitment Type Peel & Stick – Automotive Adhesive Certification ISO9001 Application Dashboard Speaker Grille Cover Compatibility Vehicle Model Year Variant Fitment Land Rover Defender 110 2020 All Trim Levels (S, SE, HSE, X) Direct Fit Land Rover Defender 90 2020 All Variants Verify Before Purchase Land Rover Defender 110 2021–2024 All Variants Verify Before Purchase Range Rover Sport L494 2013–2020 All Variants Not Compatible Range Rover Vogue L405 2013–2020 All Variants Not Compatible Installation Notes 🛠 Difficulty: Easy  ·  ⏱ Estimated Time: 15–20 minutes  ·  🔧 Tools Required: None Begin with a clean workspace. Ensure your Defender is parked and the dashboard surface is at room temperature before you start. Using a microfibre cloth and isopropyl alcohol (IPA), thoroughly clean the speaker grille area on the dashboard. Remove any dust, oils, or residue and allow to dry completely — this is the most important step for long-term adhesion. Carefully peel away the protective backing from the adhesive tape on the reverse of the cover, taking care not to touch the adhesive surface with your fingers. Align the cover precisely over the speaker grille, checking positioning before committing. The net pattern should sit centred and level with the surrounding dashboard trim. Apply firm, even pressure across the full surface of the cover for 30–60 seconds to activate the adhesive bond. Work from the centre outwards to avoid air pockets. Allow the adhesive to cure for a minimum of 24 hours before exposing the vehicle to moisture or extreme temperatures. ⚠ Important: Do not apply to a damp, dusty, or freshly cleaned surface that hasn't been allowed to dry fully. Avoid installation in temperatures below 10°C or above 35°C. If in doubt, professional fitting is recommended to ensure the best long-term result. Built for Defenders. Backed by Victorious. Join over 12,300 Land Rover owners who trust Victorious Automotive for premium interior and exterior upgrades. Every order ships worldwide via DHL, FedEx, UPS, and TNT — and is protected by our 30-day money-back guarantee. Shop All Defender 110 Accessories Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 📦 Worldwide Shipping via DHL, FedEx, UPS & TNT 🔁 30-Day Money-Back Guarantee 📞 +44 203 943 9919 Mon–Fri, 9am–7pm Victorious Automotive is an independent aftermarket accessory retailer. We are not affiliated with, endorsed by, or in any way officially connected to Land Rover, Jaguar Land Rover (JLR), or any of their subsidiaries. All vehicle names, model codes, and trademarks referenced are the property of their respective owners and are used solely for fitment identification purposes.

Victorious Automotive · Defender L663 · Collectibles & Scale Models Large 1:18 Land Rover Defender L663 SUV Off-Road Alloy Die-Cast Scale Model A precision-engineered 1:18 alloy replica of the iconic Defender L663 — built for collectors and enthusiasts who demand authentic detail and real presence on the shelf. Defender L663 2020–2026 1:18 Scale Die-Cast Alloy Sound & Light Effects Opening Doors Front Wheel Steering Shock Absorbers Collector's Edition 2020 Exterior Overview The Land Rover Defender L663 is one of the most celebrated SUV redesigns in modern automotive history. Reintroduced in 2020 after a 24-year hiatus, the new Defender retained every ounce of its legendary off-road pedigree while introducing a bold, contemporary design language that immediately became a cultural icon. It is the vehicle that defines a generation of Land Rover ownership — and now, it deserves a place in your home as well as your driveway. This 1:18 scale die-cast alloy model captures the unmistakable silhouette of the Defender L663 in extraordinary detail. From the upright Alpine windows and squared-off roofline to the exposed bonnet-mounted spare wheel provision and distinctive front grille, every exterior cue has been faithfully reproduced. The premium alloy and ABS construction gives this model a satisfying heft that plastic replicas simply cannot match — this is a piece built to be handled, displayed, and admired. Featuring functional opening doors, working sound and light effects, four-wheel independent shock absorbers, and front-wheel steering, this model goes well beyond passive display. It is as close to the real Defender experience as 1:18 scale allows — and at 27.5 cm in length, it commands attention on any desk, shelf, or display cabinet. Whether you are a dedicated Defender owner looking to commemorate your vehicle, or a collector building a premium Land Rover collection, this model is an essential addition. What's Included 🚙 1:18 Scale Defender L663 Model Die-cast alloy and ABS plastic construction 📦 Collector's Presentation Box Protective packaging suitable for gifting or storage Product Highlights Premium die-cast alloy and ABS plastic construction for exceptional weight and durability Faithful 1:18 scale reproduction of the Defender L663 2020 exterior design Available in striking Defender-inspired blue and green colourways Functional opening doors — both front and rear — for interior access and display versatility Built-in sound effects replicating engine start and drive audio for an immersive experience LED light effects on headlights and taillights for realistic nighttime display presence Four-wheel independent shock absorber system mirrors real Defender suspension geometry Working front-wheel steering via manual input — steer left and right realistically Dimensions of 27.5 x 11 x 11.5 cm — large enough to command a shelf or desktop display An ideal gift for Defender owners, Land Rover enthusiasts, and die-cast collectors Compatibility Vehicle Code Years Fitment Land Rover Defender 90 / 110 / 130 L663 2020–2026 Direct Replica Range Rover Vogue L460 2022–2026 Not This Model Range Rover Sport L461 2022–2026 Not This Model Range Rover Vogue L405 2013–2020 Not This Model Range Rover Sport L494 2013–2020 Not This Model Range Rover Velar L560 2018–2022 Not This Model Classic Defender L316 Pre-2016 Not This Model Display & Setup Notes 🛠 Setup Difficulty: None  ·  Display Ready In: Under 2 Minutes Remove the model carefully from its presentation packaging, taking care to detach any securing ties or foam inserts holding the chassis and body. Inspect the model for any transit movement — gently open and close each door to confirm hinges are properly seated and operating smoothly. Install the required batteries (AA or AAG — please refer to the battery compartment housing on the underside of the model) to activate sound and light functions. Position the model on a flat, stable display surface. A glass shelf or dedicated die-cast display cabinet is recommended to protect paintwork from dust and UV exposure. Use the manual steering function by gently turning the front axle assembly left or right to set your preferred display angle. ⚠ Note: Batteries are not included and cannot be shipped via air freight due to international aviation regulations. Standard AA or AAG batteries are available at any local retailer. Please allow ±0.5 cm dimensional variance due to manual measurement tolerances. Minor colour differences between product photography and physical unit may occur due to screen calibration variation. Built for Those Who Live the Defender Story At Victorious Automotive, every product we carry is chosen with the Land Rover owner in mind. This Defender L663 scale model is more than a replica — it is a tribute to one of the greatest off-road vehicles ever built. Browse the full Defender L663 collection or save on your next order with our exclusive discount code below. Shop Defender L663 Collection → Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 Stars — 12,300+ Verified Reviews 🔄 30-Day Money-Back Guarantee ✈️ Worldwide Shipping via DHL, FedEx, UPS & TNT 📞 +44 203 943 9919 Mon–Fri, 9am–7pm Victorious Automotive is an independent aftermarket retailer and is not affiliated with, endorsed by, or connected to Jaguar Land Rover Limited, Land Rover, or any of their subsidiaries. All vehicle names, model codes, and trademarks referenced — including Defender, Land Rover, and L663 — are the property of their respective owners and are used solely for the purpose of product compatibility identification. This product is a third-party scale model collectible and is not an official Land Rover or JLR licensed product.

Victorious Automotive · Defender L663 · Interior Trim Land Rover Defender 110 Carbon Fiber AC Vent Frame Trim — Front Air Outlet (2020–2026, L663) A precision-formed carbon fiber finish trim that transforms the Defender 110's front AC vent surrounds into a polished, purposeful interior detail — no tools, no fuss, no compromise. Defender L663 2020–2026 Carbon Fiber Finish High-Quality ABS Peel & Stick Front Air Outlet Interior Trim Direct Fit Overview The Defender 110 L663 is Land Rover's most deliberate design statement in a generation — a vehicle that balances rugged capability with a surprisingly considered interior. But even from the factory, certain details invite refinement. The front AC vent frames, while functional, sit flat and understated against the dashboard. For owners who've already invested in the Defender experience, this is an easy upgrade worth making. These AC Vent Frame Trim covers are precision-cut to match the exact profile of the Defender 110's front air outlet surrounds. Available in a carbon fiber finish, they introduce a layer of visual depth and contrast that suits the Defender's architectural interior aesthetic without looking aftermarket. The ABS substrate is rigid enough to maintain shape over time, and the 3M-style adhesive backing bonds cleanly to the factory plastic without leaving residue or requiring any permanent modification. Where this trim excels is in the detail. Carbon fiber patterning is applied with consistent texture across the face of each piece, and the fit — being custom-developed for the L663 platform — eliminates the gaps and misalignments you'd expect from generic trim kits. If you care about how your Defender looks at the level of interior finishing, this is a straightforward and satisfying addition. What's Included 🪟 Front AC Vent Frame Covers 1 complete set — pre-cut for Defender 110 front air outlets 🔲 Carbon Fiber Finish ABS Trim High-quality ABS with carbon fiber surface texture 🏷️ Pre-Applied Adhesive Backing 3M-style peel-and-stick — ready to install out of the box 📋 Fitting Guide Simple step-by-step instructions included Product Highlights Custom-developed specifically for the Defender 110 L663 front AC vent profile Carbon fiber surface finish adds visual depth and premium contrast High-quality ABS construction — rigid, warp-resistant, and long-lasting Pre-applied adhesive backing for a clean, tool-free installation No drilling, cutting, or modification to factory trim required Residue-free removal — protects original OEM plastic underneath Consistent texture and colour across all included pieces Designed to withstand dashboard heat and UV exposure over time Subtle upgrade that enhances the interior without altering the Defender's character Pairs well with other carbon fiber interior trim upgrades for a cohesive finish Compatibility Vehicle Code Years Fit Land Rover Defender 110 L663 2020–2026 Direct Fit Land Rover Defender 90 L663 2020–2026 Verify Before Purchase Land Rover Defender 130 L663 2022–2026 Verify Before Purchase Range Rover Sport L494 L494 2013–2022 Not Compatible Range Rover Vogue L405 L405 2013–2021 Not Compatible Range Rover Velar L560 2018–2022 Not Compatible Range Rover Sport L461 L461 2022–2026 Not Compatible Installation Notes Difficulty: Easy  ·  Estimated Time: 10–15 minutes  ·  Tools Required: None Start with a clean interior — ensure the front AC vent surrounds are free of dust, grease, and any dashboard protectant products. A 70% isopropyl alcohol wipe works perfectly. Allow the surfaces to dry fully before proceeding. Any moisture beneath the adhesive will reduce long-term bonding strength. Test-fit each trim piece without removing the adhesive backing first. Confirm alignment and positioning against the vent frame edges. Once satisfied with the fit, peel back the adhesive liner and carefully position the trim onto the vent frame — working from one edge to avoid air bubbles. Apply firm, even pressure across the entire surface of each piece for 30–60 seconds to activate the adhesive bond. Avoid operating the AC vents aggressively for the first 24 hours to allow the adhesive to fully cure in position. ⚠ Note: Ensure your specific Defender 110 variant matches the L663 platform (2020 onwards). Pre-2020 Defender models use an entirely different interior architecture and are not compatible with this trim set. If you're unsure, contact us at +44 203 943 9919 before ordering. Upgrade Your Defender's Interior Explore the full range of Defender L663 interior accessories at Victorious Automotive — trusted by over 12,300 Land Rover owners worldwide. Buy any two items and save 20% with the code below. Shop Defender 110 Collection Use code: 22GET20 — 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 📦 Worldwide shipping via DHL, FedEx & UPS 🔄 30-day money-back guarantee 📞 Expert support Mon–Fri, 9am–7pm Victorious Automotive is an independent aftermarket accessories retailer. We are not affiliated with, endorsed by, or connected to Jaguar Land Rover Limited (JLR), Land Rover, or any of their subsidiaries. All vehicle names, model codes, and trademarks referenced are used for fitment identification purposes only and remain the property of their respective owners.

Victorious Automotive · Defender L663 · Interior Trim Air Conditioning Console Trim for Land Rover Defender 110 (2020) — Chrome, Oak & Carbon Fiber Elevate your Defender 110's cabin with a precision-fit AC mode button frame trim, available in Chrome, Oak Grain, and Carbon Fiber finishes for a refined, personalised interior look. Defender L663 2020 ABS Material Chrome Oak Grain Carbon Fiber Direct Fit No Drilling ISO9001 Certified Overview The 2020 Land Rover Defender 110 marked a bold reintroduction of one of the most iconic 4x4s ever built — a vehicle that blends genuine off-road capability with a surprisingly considered interior. For owners who want to honour that ambition, the details matter. Every surface you interact with should feel intentional, and the air conditioning console is one of the most frequently touched areas in the cabin. This AC mode button frame trim is designed specifically for the 2020 Defender 110 (L663), fitting precisely around the climate control interface on the centre console. Available in three distinct finishes — polished Chrome, warm Oak Grain, and technical Carbon Fiber — each variant has been engineered from high-grade ABS to replicate the texture and depth of the material it represents, without adding unnecessary weight to the installation. The result is a subtle but impactful cabin upgrade that requires no specialist tools and no modifications to your vehicle. Whether you're building out a full interior transformation or simply want one well-chosen detail to stand out, this trim delivers exactly that — crafted to a standard that suits a Defender of this generation. What's Included 🪟 AC Button Frame Trim 1 × trim piece in your chosen finish 🔧 Automotive Adhesive Tape Pre-applied 3M-grade bonding tape 📄 Installation Guide Step-by-step fitting instructions included Product Highlights Precision-engineered specifically for the 2020 Defender 110 (L663) centre console Available in Chrome, Oak Grain, and Carbon Fiber — three distinct aesthetic directions High-grade ABS construction for long-term durability and resistance to fading Lightweight at just 17g — no impact on console function or button travel Pre-applied automotive adhesive tape for a clean, tool-free installation ISO9001 certified manufacturing for consistent quality and finish accuracy No drilling, cutting, or permanent modification required Each finish is textured to authentically replicate its material — not printed or flat Designed to sit flush with OEM panel lines for a factory-integrated appearance Pairs well with other Defender L663 interior trim accessories for a cohesive cabin build Compatibility Vehicle Code Year Compatibility Land Rover Defender 110 L663 2020 Direct Fit Land Rover Defender 90 L663 2020 Verify Before Purchase Land Rover Defender 130 L663 2022+ Verify Before Purchase Range Rover Sport L494 L494 2013–2020 Not Compatible Range Rover Vogue L405 L405 2013–2020 Not Compatible Range Rover Velar L560 2018–2022 Not Compatible Installation Notes ⏱ Estimated Time: 10–15 minutes  ·  🔧 Difficulty: Beginner Begin with the engine off and the cabin at room temperature. Ensure the centre console surface is clean, dry, and free from dust or grease. Use a microfibre cloth and a small amount of isopropyl alcohol to wipe down the target area around the AC mode buttons. Allow to dry fully before proceeding. Test-fit the trim piece without removing the adhesive backing to confirm alignment with the button frame and panel edges. Once satisfied with the positioning, peel the protective film from the adhesive tape on the reverse of the trim piece. Carefully press the trim into position, applying firm, even pressure across the entire surface for 30–60 seconds to activate the adhesive bond. Avoid using the climate controls and keep the area dry for a minimum of 72 hours to allow the adhesive to cure fully. ⚠ Important: Do not apply this trim to a warm or recently cleaned surface with residual moisture. Installing in cold conditions may reduce initial adhesion — allow the vehicle interior to reach a comfortable ambient temperature before fitting. If in doubt, contact our team on +44 203 943 9919. Complete Your Defender Interior This AC console trim is just the beginning. Explore our full range of Defender 110 (L663) interior accessories — from dashboard surrounds to door handle covers — all designed to the same standard of fit and finish. Shop Defender 110 Accessories → Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 🔄 30-Day money-back guarantee 🌍 Worldwide shipping via DHL, FedEx, UPS & TNT 📞 Mon–Fri 9am–7pm · +44 203 943 9919 Victorious Automotive is an independent aftermarket accessories retailer. This product is not manufactured by, affiliated with, or endorsed by Land Rover, Jaguar Land Rover (JLR), or any of their subsidiaries. All vehicle names, model codes, and trademarks referenced are used solely for the purpose of fitment compatibility and remain the property of their respective owners. Always verify compatibility with your specific vehicle configuration before purchase.

Victorious · Defender L663 · Interior Trim ABS Carbon Fiber Central Control Water Cup Holder Cover – Defender 90/110/130 Premium carbon-fibre finish cup holder frame elevates your Defender's cabin with rally-inspired interior styling. L663 Defender 2025+ Carbon Fiber ABS Central Console Direct Fit Overview The 2025 Land Rover Defender 90, 110, and 130 represent a new generation of capability—and your interior should reflect that same attention to detail. This ABS carbon-fiber central control water cup holder cover replaces the standard trim with a modern, high-tech finish that catches light and commands attention every time you reach for a drink. Precision-molded from impact-resistant ABS plastic with an authentic carbon-fiber weave texture, this cover integrates seamlessly with your Defender's console layout. It's not just aesthetic—it protects the surrounding trim from wear while adding a layer of sophistication that factory plastic simply cannot deliver. Whether you're exploring urban terrain or pushing into the backcountry, this upgrade delivers the kind of interior refinement that separates a well-appointed Defender from the rest. Installation is straightforward, requiring no modifications to your vehicle. What's Included 🎯 Carbon Fiber Cover Central control water cup holder frame ⚙️ Hardware Kit All fasteners and clips included 📋 Installation Guide Step-by-step visual instructions ✓ Quality Assurance Tested for Defender fit and finish Product Highlights Authentic carbon-fiber weave texture with premium ABS construction Perfect fit for 2025+ Defender 90, 110, and 130 models Protects factory trim from daily wear and spills Non-intrusive design maintains cup holder functionality Modern aesthetic complements contemporary Defender cabin design Lightweight and durable impact-resistant material No vehicle modifications required for installation Easy to clean and maintain over time Coordinates with other carbon-fiber interior upgrades Factory-quality fitment and alignment Compatibility Defender Model Year Range Compatibility Defender 90 2025+ Direct Fit Defender 110 2025+ Direct Fit Defender 130 2025+ Direct Fit Defender L663 (Pre-2025) 2020–2024 Not Compatible Defender 90/110 (L316) 2004–2016 Not Compatible Installation Difficulty Level: Beginner | Estimated Time: 15 minutes Power off your vehicle and remove the ignition key. Locate the central control water cup holder frame on your Defender's console. Carefully release the factory cover clips using gentle pressure at the designated points. Remove the original trim piece and set aside. Align the carbon-fiber cover with the mounting points on your console. Press firmly until all clips engage and the cover sits flush with surrounding trim. Test cup holder functionality to ensure proper operation. Reconnect your ignition and verify alignment under interior lighting. Note: Do not force the cover into place. If resistance is felt, recheck alignment. All factory clips should engage smoothly without excessive pressure. Why Victorious We've been outfitting Land Rover and Range Rover owners for over a decade. Every product in our collection is tested against real-world Defender use, and we stand behind every upgrade with a 30-day money-back guarantee. Our team of enthusiasts understands that your Defender deserves better—and we deliver parts that prove it. Ready to Elevate Your Defender Interior? Upgrade your central console with this premium carbon-fiber cover. Factory quality. Enthusiast finish. Built to last. Shop Defender Upgrades Use code 22GET20 for 20% off any 2 items ✓ 30-Day Money Back ✓ 4.9/5 Stars – 12,300+ Reviews ✓ Worldwide Shipping via DHL & FedEx ✓ +44 203 943 9919 – Expert Support Disclaimer: Victorious Automotive is an independent aftermarket accessory supplier and is not affiliated with, endorsed by, or connected to Land Rover, Range Rover, or Jaguar Land Rover Limited. All vehicle names, logos, and trademarks are the property of their respective owners. This product is designed for use with the vehicles listed and does not modify or alter factory systems. Owners are responsible for ensuring compatibility with their specific vehicle configuration.

Victorious Automotive · Defender L663 · Interior Trim Land Rover Defender L663 110 Trunk Door Slot Decorative Panel — Stainless Steel (2020–2021) A precision-cut stainless steel trunk door slot trim that brings polished definition to your Defender 110's rear interior — installed in minutes, built to last. Defender L663 2020–2021 Stainless Steel Bright Finish Peel & Stick ISO9001 Certified Interior Trim Trunk Door Panel Overview The Defender L663 110 is one of the most talked-about vehicles of its generation — a vehicle that bridges genuine off-road capability with a surprisingly considered, upscale interior. Land Rover's 2020 relaunch of the Defender brought an entirely new platform and an interior ethos that rewards careful customisation. Every surface matters, and the smaller details — those that catch the eye as you open the tailgate or load the boot — are exactly where quality accessories earn their place. This trunk door slot decorative panel is designed specifically for the Defender 110 L663 (2020–2021). Crafted from polished stainless steel with a bright mirror-like finish, the panel sits neatly within the door slot recess at the rear of the vehicle, replacing the bare unpanelled gap with a clean, purposeful strip of trim. At 64cm long and precisely contoured to the factory profile, it slots into position without modification and adheres securely using pre-applied automotive-grade adhesive tape. Where plastic trim and unfinished edges can undermine an otherwise premium interior, this panel adds exactly the kind of subtle, considered detail that enthusiasts notice. The stainless steel construction resists corrosion, handles temperature extremes, and holds its finish over time — making this a long-term upgrade rather than a short-lived cosmetic fix. It's the sort of finishing touch that looks like it should have come from the factory. What's Included 🪟 Trunk Door Slot Decorative Panel 1x stainless steel trim panel, 64cm × 10cm × 4cm 🔖 Pre-Applied Adhesive Tape Automotive-grade 3M-style mounting tape pre-fitted to rear 📄 Installation Guide Step-by-step fitment instructions included in packaging Product Highlights Polished stainless steel construction — resistant to corrosion and daily wear Bright mirror finish that complements the Defender's premium interior aesthetic Precision-cut to 64cm to match the Defender 110 L663 trunk door profile exactly Pre-applied automotive adhesive tape for a clean, tool-free installation No drilling, cutting, or modification required to your vehicle Lightweight at 273g — no added stress to door structure or hinges ISO9001 quality certified manufacturing for consistent finish and fitment Designed to withstand temperature cycling, humidity, and loading bay use Enhances the appearance of the boot area when the tailgate is open Direct-fit for Defender 110 L663 2020–2021 — no adaptation needed Compatibility Model Code Year Range Fitment Defender 110 L663 2020–2021 Direct Fit Defender 90 L663 2020–2021 Not Compatible Defender 130 L663 2022–2026 Not Compatible Defender 110 L663 2022–2026 Verify Before Purchase Range Rover Sport L494 / L461 All Years Not Compatible Range Rover Vogue L405 / L460 All Years Not Compatible Installation Notes 🛠 Difficulty: Easy  ·  ⏱ Estimated Time: 10–15 Minutes  ·  🔧 Tools Required: None Open the Defender 110's tailgate fully and locate the trunk door slot recess where the panel will be fitted. Using a clean microfibre cloth and isopropyl alcohol (IPA), thoroughly clean and degrease the mounting surface. Remove any dust, oils, or residue. Allow to dry completely — at least 3–5 minutes. Test-fit the panel without removing the adhesive backing to confirm alignment and positioning along the slot recess. Peel away the adhesive tape backing from the rear of the decorative panel, taking care not to touch the adhesive surface. Starting from one end, carefully align the panel and press firmly into position along the door slot, applying consistent pressure across the full length for 30–60 seconds. Allow the adhesive to cure for a minimum of 24 hours before exposing to heavy moisture or loading the boot aggressively. ⚠ Important: Surface temperature should be between 15°C and 35°C during installation for optimal adhesive performance. Do not install on a cold or damp surface. Always verify your exact model and build year before fitting. If in doubt, contact us at +44 203 943 9919 (Mon–Fri, 9am–7pm). Upgrade Your Defender's Interior Today Explore our full range of Defender L663 interior accessories — each one selected and tested to meet the standards your vehicle deserves. Worldwide shipping via DHL, FedEx, UPS, and TNT. Backed by our 30-day money-back guarantee. Shop Defender L663 Accessories Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 Stars — 12,300+ Verified Reviews 📦 Worldwide Shipping — DHL, FedEx, UPS, TNT 🔁 30-Day Money-Back Guarantee 📞 +44 203 943 9919 — Mon–Fri, 9am–7pm Victorious Automotive is an independent aftermarket accessory retailer. We are not affiliated with, endorsed by, or associated with Land Rover, Jaguar Land Rover (JLR), or any of their subsidiaries. All vehicle names, model codes, and trademarks referenced are the property of their respective owners and are used solely for fitment identification purposes. Always verify compatibility with your specific vehicle configuration before purchase.

Victorious Automotive · Defender L663 · Interior Trim Left-Hand Drive ABS Black Interior Window Lifter Switch Trim for 2020 Land Rover Defender 110 A precision-formed ABS black switch surround that refines the door panel aesthetic of the 2020 Defender 110 — clean lines, factory-level fitment, zero compromise. Defender L663 2020 Model Year Left-Hand Drive ABS Black Window Lifter Switch Trim Interior Trim No-Drill Install ISO9001 Certified Overview The 2020 Land Rover Defender L663 was a complete reimagining of one of the most iconic vehicles ever made — bold, capable, and designed with an interior that finally matched its exterior ambition. Yet for owners who want every detail to feel intentional, the door panel window lifter switch area is one of those subtle surfaces that benefits enormously from a well-fitted trim overlay. It's a small change that shifts the feel of the entire door card. This ABS Black Window Lifter Switch Trim is engineered specifically for the Left-Hand Drive Defender 110 (2020 onwards), offering a snug, factory-matched surround for the window control switch cluster. Formed from high-grade ABS material and finished in a clean gloss black, it integrates seamlessly with the Defender's existing interior language — adding definition without distraction. At 29cm long and weighing just 148g, the trim is lightweight yet rigid, built to resist flex, temperature variation, and daily door use without lifting or fading. Installation requires no tools, no drilling, and no professional fitting — automotive-grade adhesive tape is pre-applied, meaning this is a genuine weekend upgrade that takes minutes and lasts years. Whether you're building out a full interior refresh or simply want a more considered finish on your Defender's door panels, this trim is exactly the kind of detail-oriented accessory that separates a standard Defender from a truly personal one. What's Included 🪟 Window Lifter Switch Trim 1× full set — LHD Defender 110 fitment 🔧 Pre-Applied Adhesive Tape Automotive-grade, heat-resistant backing 📄 Fitting Guide Step-by-step installation instructions included 📦 Protective Packaging Secure box — arrives scratch-free, ready to fit Product Highlights Precision-engineered for Left-Hand Drive Defender 110 (2020) — exact fitment, no gaps Premium ABS construction — rigid, lightweight, and resistant to daily wear Gloss black finish — complements both dark and light Defender interior colour packs ISO9001 certified manufacturing — consistent quality control at every stage No-drill, no-cut installation — adhesive-backed for a clean, reversible fit Dimensions: 29cm × 12cm × 4cm — purpose-sized for the LHD switch panel Weighs just 148g — no added bulk or door panel stress Heat and UV stable — maintains finish in all climates Compatible with Defender 110 standard and specification variants (LHD, 2020) Pairs with other Victorious Defender L663 interior trim pieces for a cohesive upgrade Compatibility Vehicle Year Drive Body Style Fit Land Rover Defender 110 (L663) 2020 Left-Hand Drive 110 (5-door) Direct Fit Land Rover Defender 130 (L663) 2020 Left-Hand Drive 130 (Extended) Direct Fit Land Rover Defender 90 (L663) 2020 Left-Hand Drive 90 (3-door) Verify Before Purchase Land Rover Defender 110 (L663) 2020 Right-Hand Drive 110 (5-door) Not Compatible Land Rover Defender (Pre-2020 / Classic) Pre-2020 Any Any Not Compatible Range Rover Sport / Vogue / Velar Any Any Any Not Compatible Installation Notes 🛠 Difficulty: Easy  ·  ⏱ Estimated Time: 10–15 Minutes  ·  🔩 Tools Required: None Begin with the vehicle parked and the door panel at room temperature. Avoid fitting in direct sunlight or extreme cold, as this affects adhesive performance. Thoroughly clean the window lifter switch surround area using an isopropyl alcohol wipe or panel prep solution. Remove all dust, grease, and residue. Allow to dry completely — this step is critical for long-term adhesion. Dry-fit the trim piece against the switch panel to confirm alignment and coverage before committing. Note the natural orientation and any reference points on the door card. Peel back the protective film from the pre-applied adhesive tape on the reverse of the trim. Do not touch the adhesive surface. Carefully align the trim piece to the switch surround, starting from one edge and pressing firmly across the full surface. Apply sustained hand pressure for 30–60 seconds to activate the adhesive bond. Allow 24 hours for the adhesive to fully cure before operating windows repeatedly or subjecting the trim to heavy contact. ⚠ Important: This trim is designed for Left-Hand Drive Defender 110 models only. Attempting to fit on a Right-Hand Drive vehicle will result in incorrect alignment. If you're unsure of your vehicle's specification, check your VIN or contact us at +44 203 943 9919 before ordering. Complete Your Defender Interior This window lifter switch trim is just the beginning. Explore the full Victorious range of Defender L663 interior upgrades — from dashboard overlays to gear surround trims — and build an interior that feels entirely your own. Shop All Defender L663 Accessories Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 🔄 30-Day money-back guarantee ✈️ Worldwide shipping via DHL, FedEx, UPS & TNT 📞 Expert support Mon–Fri, 9am–7pm · +44 203 943 9919 Victorious Automotive is an independent retailer of aftermarket and styled accessories for Land Rover and Range Rover vehicles. This product is not manufactured by, endorsed by, or affiliated with Land Rover, Jaguar Land Rover (JLR), or any of their subsidiaries. All vehicle names, model codes, and trademarks are the property of their respective owners and are referenced solely for the purpose of fitment compatibility.

Victorious Automotive · Defender L663 · Interior Trim Oak ABS Front Air Vent Cover Frame for Land Rover Defender 110 (2020–2026) L663 A precision-fit oak wood grain ABS overlay that brings warm, natural texture to the Defender 110's front air vent surrounds — no tools, no drilling, no compromise. Defender L663 2020–2026 Oak Wood Grain High-Quality ABS Direct Fit Peel & Stick LHD Only Interior Trim ISO9001 Certified Overview The Land Rover Defender 110 L663 represents a genuine reimagining of an icon — purposefully engineered, architecturally bold, and unmistakably modern inside. Its cabin is designed to be functional yet characterful, and the air vent surrounds sit front and centre on the fascia, making them one of the most visible surfaces in the entire interior. These Oak ABS Front Air Vent Cover Frames are designed specifically for that space. Finished in a warm oak wood grain, they introduce a natural, organic contrast against the Defender's industrial material palette. Whether your Defender is specced in Ebony, Lunar or Pimento, the oak finish adds a layer of crafted warmth that the standard trim simply doesn't offer. The ABS substrate ensures the panels are rigid, precisely contoured and built to last — not a flimsy film, but a structured overlay with genuine presence. Installation requires no specialist tools or professional fitting. Each panel is engineered to locate precisely over the existing vent frame and bonds cleanly using factory-grade adhesive backing. The result is a factory-finish appearance that looks like it came straight from a customisation workshop — because, in every meaningful sense, it did. What's Included 🪵 Oak ABS Vent Cover Frame × 2 Left and right front air vent surrounds in oak wood grain finish 🔖 Pre-Applied Adhesive Backing Factory-grade 3M-style adhesive — no additional fixings required 📋 Installation Guidance Step-by-step fitting instructions included in packaging Product Highlights Oak wood grain finish adds natural warmth to the Defender's industrial interior High-quality ABS construction — rigid, structured, and built for longevity Precision-moulded to match the exact contours of the L663 vent frames Peel-and-stick installation — no drilling, no clips, no professional fitting needed Factory-grade adhesive backing for a clean, flush bond to the original trim 100% brand new — supplied in protective packaging to prevent transit damage Manufactured in an ISO9001 certified facility for consistent quality assurance Covers both left and right front air vent surrounds — a complete front fascia upgrade Compatible with Defender 110 and 130 L663 models from 2020 onwards Designed exclusively for Left Hand Drive (LHD) Defender variants Compatibility Vehicle Model Code Year Range Drive Fitment Land Rover Defender 110 L663 2020–2026 LHD Direct Fit Land Rover Defender 130 L663 2022–2026 LHD Direct Fit Land Rover Defender 90 L663 2020–2026 LHD Verify Before Purchase Land Rover Defender 110 L663 2020–2026 RHD Not Compatible Land Rover Defender (Original) Pre-2020 All Years Any Not Compatible Range Rover / Discovery Any All Years Any Not Compatible Installation Notes Difficulty: Easy  ·  Estimated Time: 15–20 Minutes  ·  Tools Required: None Begin with a clean, dry interior. Wipe down the existing air vent surrounds using an isopropyl alcohol wipe or interior detailer to remove any dust, oils or residue that could affect adhesion. Allow the surface to dry fully. Do not apply the covers to a damp or recently cleaned surface — a minimum of 5 minutes drying time is recommended. Dry-fit each cover frame against its corresponding vent surround before removing the adhesive backing. Confirm alignment and orientation — the panels are handed (left and right), so ensure each one is correctly positioned before committing. Peel back a small section of the adhesive liner, align the panel carefully to the vent surround edges, and press down from the centre outward to avoid air pockets. Once positioned, apply firm, even pressure across the entire surface for 30–60 seconds to activate the adhesive bond. Work from the centre toward each corner. Repeat the process for the second panel. Leave the interior undisturbed for a minimum of 24 hours before exposing to heat or direct sunlight, to allow the adhesive to cure fully. ⚠ Important: These covers are designed exclusively for Left Hand Drive (LHD) Defender 110 and 130 L663 models. Right Hand Drive vehicles are not compatible. Please confirm your vehicle's drive configuration before ordering. If you are unsure, contact our team on +44 203 943 9919 (Mon–Fri, 9am–7pm) before purchasing. Upgrade Your Defender's Interior Today Join over 12,300 Land Rover and Defender owners who trust Victorious Automotive for premium interior accessories. Browse the full Defender L663 collection and refine every detail of your cabin. Shop Defender L663 Accessories → Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 Stars — 12,300+ Verified Reviews 📦 Worldwide Shipping via DHL, FedEx, UPS & TNT 🔁 30-Day Money-Back Guarantee 📞 Expert Support Mon–Fri, 9am–7pm 🏭 ISO9001 Certified Manufacturing Victorious Automotive is an independent retailer and is not affiliated with, endorsed by, or connected to Land Rover, Jaguar Land Rover (JLR), or any of their subsidiaries. All vehicle names, model codes, and trademarks referenced are the property of their respective owners and are used solely for fitment identification purposes. Always verify compatibility with your specific vehicle before purchase.

Victorious Automotive · Defender L663 · Interior Trim Chrome ABS Armrest Box Rear Air Conditioning Vent Trim for Land Rover Defender 110 L663 (2023+) A precision-engineered chrome ABS trim panel that integrates seamlessly with the rear armrest air conditioning vent on the 2023+ Defender 110, elevating your cabin's finish with zero permanent modification. Defender 110 L663 2023–2026 Chrome Finish ABS Material Rear Armrest Trim AC Vent Panel ISO9001 Certified No-Drill Fit Model: LLK2783 Overview The Land Rover Defender 110 L663 is one of the most purposeful and design-led cabins in the 4x4 world — a deliberate blend of utilitarian precision and modern detailing. From the 2023 model year onward, the rear centre console and armrest box received revised surfacing that creates a particularly clean canvas for interior upgrades. Every detail in this cabin is intentional, and that same philosophy should extend to how you personalise it. This chrome ABS armrest box rear AC vent trim has been developed specifically to suit the revised 2023+ Defender 110 interior. It wraps the rear air conditioning vent housing with a highly polished chrome-effect ABS surround, replacing the standard plastic finish with something that reads as genuinely premium. The fitment is precise, the surface quality is consistent, and the overall effect is of an interior that has been attended to — not merely accessorised. Made from high-grade ABS to ISO9001 quality standards, this panel is lightweight at just 300g and installs entirely via automotive-grade adhesive tape — no cutting, no drilling, no permanent alteration. It's the kind of upgrade that looks factory-fit from day one and holds up to the demands of daily use across all conditions the Defender is built for. What's Included 🪞 Chrome ABS AC Vent Trim Panel 1x rear armrest box surround — chrome finish 🔧 Automotive Adhesive Tape Pre-cut, high-bond — ready for installation 📋 Installation Guide Step-by-step fitment reference included Product Highlights Specifically engineered for the 2023+ Defender 110 L663 rear armrest AC vent housing High-gloss chrome-effect ABS finish — polished, consistent, and durable ISO9001 certified manufacturing for quality assurance and dimensional accuracy No drilling, cutting, or permanent modification required — fully reversible fit Lightweight at 300g — no added load on trim panels or surrounding surfaces Automotive-grade adhesive tape included for a secure, long-lasting bond Dimensions: 10cm (H) × 30cm (L) × 15cm (W) — precision-matched to OEM fitment Also available in Carbon Fibre and Oak Wood Grain finishes to suit your interior style Installs in under 30 minutes with no specialist tools required Enhances the rear passenger experience with a noticeably more refined interior detail Compatibility Vehicle Model Code Year Range Fitment Land Rover Defender 110 L663 2023–2026 Direct Fit Land Rover Defender 90 L663 2023–2026 Verify Before Purchase Land Rover Defender 130 L663 2023–2026 Verify Before Purchase Land Rover Defender 110 L663 2020–2022 Not Compatible Range Rover Sport L461 2022–2026 Not Compatible Range Rover Vogue L460 2022–2026 Not Compatible Range Rover Velar L560 2018–2022 Not Compatible Installation Notes Difficulty: Easy  ·  Estimated Time: 15–30 Minutes  ·  Tools Required: None Begin by thoroughly cleaning the rear armrest AC vent surround with a lint-free cloth. Remove any dust, grease, or moisture — the surface must be completely clean and dry before proceeding. Dry-fit the chrome trim panel against the vent housing to confirm alignment and verify the fit before committing to adhesion. Peel the backing from the pre-cut automotive adhesive tape and carefully apply it to the rear face of the trim panel, ensuring full coverage across all contact points. Align the panel precisely with the vent surround, starting from one edge and pressing firmly across the full surface to ensure consistent contact and eliminate air pockets. Apply firm, even pressure for 30–60 seconds. Allow the adhesive to cure for a minimum of 24 hours before exposing to heat, moisture, or direct sunlight. ⚠ Important: Do not use alcohol-based cleaners immediately before installation as they may leave a residue that reduces adhesion. Avoid installation in temperatures below 10°C — cold surfaces significantly reduce adhesive bond strength. Once fitted, allow the full 24-hour cure window before operating rear climate control at maximum output. The Detail That Makes the Difference At Victorious Automotive, we stock interior trim upgrades because we know that Defender owners care about every surface in their cabin. This chrome AC vent surround is a small change with a disproportionate impact — and it's backed by our 30-day money-back guarantee and 4.9-star rating from over 12,300 verified customers worldwide. Shop All Defender L663 Accessories Use code 22GET20 for 20% off any 2 items ⭐ 4.9/5 from 12,300+ reviews 🌍 Worldwide Shipping via DHL, FedEx, UPS, TNT ↩ 30-Day Money-Back Guarantee 📞 +44 203 943 9919 Mon–Fri 9am–7pm Victorious Automotive is an independent retailer and is not affiliated with, endorsed by, or connected to Land Rover, Jaguar Land Rover (JLR), or any of their subsidiaries. All vehicle names, model codes, and trademarks referenced are the property of their respective owners and are used solely for fitment identification purposes. Product imagery and descriptions are provided for illustrative purposes. Always verify compatibility with your specific vehicle configuration before purchase. If in doubt, contact our team on +44 203 943 9919.

Victorious Automotive · Defender L663 · Interior Trim Carbon Fiber ABS Rear Armrest Air Conditioning Vent Cover for Land Rover Defender 110 L663 (2020–2023) A precision-formed carbon fibre-style ABS trim cover that elevates the rear cabin of your Defender 110 — adding a purposeful, premium aesthetic to the back-row air conditioning vent surround with zero modification required. Defender 110 L663 2020–2023 Carbon Fibre Style ABS Material Rear Armrest Vent No-Drill Fit ISO9001 Certified Interior Trim Overview The Land Rover Defender 110 L663 is a vehicle that demands accessories worthy of its character — purposeful, considered, and built to last. Its interior, while well-appointed from the factory, presents ample opportunity for owners who want to push the finish further. The rear cabin in particular — where passengers interact with the armrest-mounted air conditioning vent — is an area where a small upgrade can make a meaningful visual impact. This carbon fibre-style ABS rear armrest air conditioning vent cover is designed exclusively for the Defender 110 (2020–2023). Manufactured from high-grade ABS with an ISO9001-certified process, it wraps the existing vent surround with a clean, textured carbon fibre finish that blends seamlessly with the Defender's utilitarian-meets-refined interior language. The fit is exact — no gaps, no proud edges, no fuss. Installation is handled entirely via automotive-grade adhesive tape, meaning no drilling, no permanent modification, and no risk to your vehicle's original trim. It's the kind of detail that Defender owners who've specified their vehicles carefully will appreciate — subtle enough not to shout, refined enough to be noticed. What's Included 🪟 Rear Vent Cover 1 x carbon fibre-style ABS air outlet cover for rear armrest 🔧 Installation Instructions Step-by-step fitting guide included in the box 🩹 Automotive Adhesive Tape Pre-applied or supplied adhesive for a secure, clean bond Product Highlights Precision-engineered specifically for the Defender 110 L663 rear armrest vent surround Carbon fibre-style ABS finish that complements both dark and light interior colour schemes High-grade ABS construction — impact-resistant, UV-stable, and warp-resistant over time ISO9001-certified manufacturing process for consistent quality and dimensional accuracy No-drill, no-permanent-modification installation via automotive-grade adhesive tape Exact OEM-matching profile ensures flush fit with no visible gaps or misalignment Maintains full access to rear air conditioning controls — no obstruction whatsoever Lightweight at 300g — adds no meaningful weight to the vehicle interior Easy to clean with standard interior detailing products — no specialist care required Reversible installation — original trim can be restored without damage if required Compatibility Vehicle Code Year Range Fitment Land Rover Defender 110 L663 2020–2023 Direct Fit Land Rover Defender 90 L663 2020–2023 Verify Before Purchase Land Rover Defender 130 L663 2022–2023 Verify Before Purchase Range Rover Sport L494 L494 2013–2022 Not Compatible Range Rover Vogue L405 L405 2013–2021 Not Compatible Range Rover Velar L560 2018–2022 Not Compatible Installation Notes Difficulty: Easy  ·  Estimated Time: 15–20 Minutes  ·  Tools Required: None Begin with a clean, dry interior. Using an isopropyl alcohol wipe, thoroughly clean the surface of the existing rear armrest vent surround to remove any dust, oils, or residue. Allow the surface to dry fully — a minimum of 5 minutes at room temperature is recommended before proceeding. Test-fit the carbon fibre ABS cover against the vent surround without removing the adhesive backing. Confirm alignment and that controls remain fully accessible. Remove the adhesive protective liner from the rear of the cover, then carefully align and press the cover firmly into position from one edge to the other to prevent air pockets. Apply firm, even pressure across the entire surface for 30–60 seconds to activate the adhesive bond. Pay particular attention to the corners and edges. Allow the adhesive to cure for a minimum of 24 hours before exposing the area to extreme temperatures or moisture. ⚠ Important: Do not install in temperatures below 10°C (50°F), as adhesive performance may be significantly reduced. If in doubt, allow the vehicle interior to warm to room temperature before fitting. Professional installation is recommended if you are unfamiliar with adhesive trim accessories. Specifications Specification Detail Model Reference LLK2783 Material High-Grade ABS Plastic Finish Carbon Fibre Style Dimensions 30cm (L) × 15cm (W) × 10cm (H) Weight 300g Quality Certification ISO9001 Installation Method Automotive Adhesive Tape (No Drill) Fitment Land Rover Defender 110 L663 (2020–2023) Complete Your Defender 110 Interior Explore the full range of Defender L663 interior accessories at Victorious Automotive — crafted for owners who care about every detail. Trusted by 12,300+ Land Rover enthusiasts worldwide. Shop Defender 110 Accessories Use code 22GET20 for 20% off when you buy any 2 items ⭐ 4.9/5 from 12,300+ verified reviews 🚚 Worldwide Shipping via DHL, FedEx & UPS ↩ 30-Day Money-Back Guarantee 📞 +44 203 943 9919 Mon–Fri, 9am–7pm Victorious Automotive is an independent retailer and is not affiliated with, endorsed by, or connected to Land Rover, Jaguar Land Rover (JLR), or any of their subsidiaries. All vehicle names, model codes, and trademarks referenced are the property of their respective owners and are used solely for the purpose of product fitment identification. Fitment compatibility is provided as guidance only — customers are advised to verify suitability against their specific vehicle configuration prior to purchase.