Victorious · Land Rover Drivetrain · Bearing
Rear Propshaft Centre Support Bearing for Freelander LR2 & Range Rover Evoque
OE-specification driveshaft support bearing engineered to restore smooth transmission torque delivery and eliminate centre console vibration.
LR031394B
2006–2014 LR2
2012+ Evoque
Metal Bearing
Direct Fit
OEM Quality
Overview
Your Freelander LR2 or Range Rover Evoque's rear propshaft is supported by a centre bearing that absorbs engine torque and isolates vibration. Over 100,000 miles, this bearing wears, allowing the shaft to sag and creating a distinctive shudder through the cabin, especially under acceleration or when cornering.
This OE-specification replacement bearing (part no. LR031394B or compatible variants LR006959, LR007804, LR023283) restores the precise geometry and damping characteristics of the original, eliminating vibration and restoring confident driveline feel. The metal construction with rubber isolation mounts engineered to Land Rover factory standards.
Whether you're addressing a known vibration complaint or performing preventative maintenance at high mileage, this bearing delivers factory-proven reliability. Fits all 2006–2014 Freelander LR2 models and 2012+ Range Rover Evoque variants.
What's Included
🔧
Propshaft Centre Bearing
OEM part specification LR031394B (1 or 2 per vehicle, depending on transmission type)
✓
Fitment Verification
Matched to your VIN to confirm exact part number required
Product Highlights
-
Inner Diameter: ~30mm precision bore
-
Outer Diameter: ~105mm support flange
-
Mounting Length: ~115mm overall
-
Net Weight: ~530g per unit
-
Material: Metal construction with elastomer isolation
-
OEM Compatibility: LR031394, LR049820, LR006959, LR007804, LR023283
-
Vehicle Fitment: 2006–2014 Freelander LR2; 2012+ Range Rover Evoque
-
Transmission Type: Diesel manual and automatic 6-speed
-
Condition: New, factory sealed
-
Performance Benefit: Eliminates centre tunnel vibration and restores driveline isolation
Compatibility Chart
| Vehicle Model |
Year Range |
Part No. |
Qty Required |
Fit Status |
| Freelander LR2 (2.2L CR Diesel Manual) |
2006–2014 |
LR031394, LR049820 |
1 |
Direct Fit |
| Freelander LR2 (2.2L CR Diesel Automatic) |
2006–2014 |
LR006959, LR007804, LR023283 |
2 |
Direct Fit |
| Range Rover Evoque |
2012+ |
LR006959, LR007804, LR023283 |
2 |
Direct Fit |
| Other Land Rover / Range Rover models |
— |
Verify with VIN |
— |
Verify First |
Important: Confirm your vehicle's exact part number before purchase. Automatic transmissions require 2 bearings; manual transmissions require 1. Always verify fitment via VIN or existing part marking.
Installation Notes
⏱ Difficulty & Time
Intermediate to Advanced. Estimated 2–4 hours depending on transmission type and access. Requires vehicle lift and potentially partial exhaust or heat shield removal.
Installation Steps
- Safely raise and support vehicle on jack stands or lift.
- Disconnect and remove rear propshaft (mark orientation for reassembly).
- Unbolt the existing centre bearing bracket from the vehicle frame or transmission tunnel.
- Carefully extract the worn bearing from the mounting bracket.
- Clean the bracket and mounting surfaces; inspect for corrosion or cracks.
- Press or slide the new bearing into the bracket, ensuring rubber mounts align.
- Reinstall the bracket and torque fasteners to OEM specification (~30–40 Nm typical).
- Reattach the propshaft, aligning the marks made during removal.
- Lower vehicle and test-drive to confirm vibration is eliminated.
⚠ Specialist Tip: Propshaft work requires careful balancing and alignment. If you are unfamiliar with drivetrain service, we recommend having a qualified Land Rover specialist perform this work. Improper reassembly can cause secondary vibration or component damage.
Why Victorious?
We specialise in Land Rover and Range Rover OEM and OEM-equivalent drivetrain components. This bearing is sourced to factory specifications and tested for fitment across Freelander LR2 and Evoque model years. Every part ships with our 30-day money-back guarantee—if it doesn't resolve your vibration issue, we'll refund you in full.
Need help identifying your exact part number? Call our specialist team at +44 203 943 9919 (Mon–Fri, 9am–7pm GMT) with your VIN, and we'll confirm fitment instantly.
Ready to Eliminate Drivetrain Vibration?
Restore smooth, confident driveline feel with this OE-specification centre bearing. Direct fit for Freelander LR2 and Range Rover Evoque. Order now with our 30-day guarantee.
Shop This Bearing
Use code 22GET20 for 20% off any 2 items
4.9★ 12,300+ verified reviews
🚚 Worldwide DHL, FedEx, UPS, TNT
✓ 30-day money-back guarantee
Disclaimer: Victorious Automotive is not affiliated with Land Rover, Range Rover, Jaguar Land Rover (JLR), or any OEM manufacturer. All product names, logos, and brand references are the property of their respective owners. This product is designed for fitment to the vehicles listed and is sold as-is. Installation should be performed by a qualified technician. Always verify part compatibility with your vehicle VIN before purchase. Victorious Automotive accepts no liability for improper installation or incompatible fitment.
