Victorious · Range Rover · Cooling System
Aluminium 3.0 V6 Petrol Coolant Thermostat Housing with Sensor – L462 / L494 / L405 / L538
OEM-specification replacement thermostat housing for Range Rover, Range Rover Sport, Discovery, and Velar with integrated temperature sensor.
L462 • L494 • L405 • L538
2013–2024
Aluminium
3.0 V6 Petrol
Direct Fit
Overview
The cooling system is the silent guardian of your Range Rover's engine. When your thermostat housing begins to fail—manifesting as temperature gauge fluctuations, coolant leaks at the housing gasket, or overheating on load—it's time for a direct replacement that matches the OEM specification exactly.
This Partsmost aftermarket aluminium thermostat housing is engineered to the same tolerances as the original Land Rover component. It integrates seamlessly with your 3.0 V6 petrol engine's cooling circuit and includes the thermal sensor that communicates coolant temperature back to the ECU, ensuring your engine management system operates precisely.
Whether your Range Rover L462, Sport L494, Vogue L405, or Velar is showing signs of thermostat wear, this housing restores cooling efficiency, stabilises idle temperature, and eliminates the risk of overheat warnings on motorway drives or towing duty.
What's Included
⚙️
Thermostat Housing
Aluminium body, OEM gasket seat
🌡️
Temperature Sensor
Integrated, calibrated for ECU
📋
Fitment Guide
Vehicle-specific installation notes
✓
12-Month Warranty
Parts & labour coverage included
Product Highlights
- Aluminium construction for thermal efficiency and longevity
- OEM-specification gasket seating eliminates future leaks
- Integrated temperature sensor pre-calibrated for your engine ECU
- Direct plug-and-play fit—no modification required
- Engineered for 3.0 V6 petrol engines across Range Rover models
- Maintains precise cooling circuit balance under all load conditions
- Compatible with both manual and automatic transmissions
- Low thermal mass for rapid warm-up and stable idle
- Tested to OEM pressure and temperature tolerances
- 12-month warranty backed by Victorious Automotive
Compatibility Chart
| Vehicle |
Model Code |
Years |
3.0 V6 Petrol |
| Range Rover Vogue |
L405 |
2013–2020 |
Direct Fit |
| Range Rover Sport |
L494 |
2014–2021 |
Direct Fit |
| Range Rover Vogue |
L462 |
2022–2024 |
Direct Fit |
| Range Rover Sport |
L535 |
2022–2024 |
Not Compatible |
| Range Rover Velar |
L560 |
2018–2024 |
Direct Fit |
| Land Rover Discovery 4 |
L319 |
2015+ |
Direct Fit |
| Land Rover Discovery 5 |
L462 |
2017–2024 |
Direct Fit |
Not certain? Email us your VIN or registration plate at support@victorious.shop—we'll confirm fitment in minutes.
Installation
Difficulty Level: Intermediate | Estimated Time: 1.5–2.5 hours
-
Disconnect battery. Locate the negative terminal and remove the cable to disable electrical circuits during work.
-
Cool the engine. Allow at least 2 hours of cooling before working on the cooling system to avoid burns from residual heat.
-
Drain coolant. Place a catch pan beneath the radiator drain plug (passenger side, lower corner). Open the plug and allow coolant to drain fully into the pan.
-
Remove intake ducting. On L405/L494 models, unclip the air intake hose and upper radiator hose bracket to access the housing mounting bolts.
-
Disconnect the sensor harness. Carefully unplug the three-pin temperature sensor connector from the top of the housing.
-
Remove the old housing. Using a 10mm socket, remove the four retaining bolts. Lift the housing clear and discard the old gasket.
-
Clean the mating surface. Use a soft cloth and gasket scraper to remove all traces of old gasket material from the engine block face.
-
Install new gasket. Place the supplied O-ring gasket into the grooved seat on the housing. Do not apply sealant—the gasket seal is pre-formed.
-
Position the new housing. Align the four bolt holes and slide the housing into place. Ensure the gasket remains seated.
-
Torque the bolts. Tighten the bolts in a cross pattern (diagonal sequence) to 20 Nm (15 ft-lb). Verify all bolts are evenly tight.
-
Reconnect the sensor. Plug the three-pin connector firmly into the sensor. You should hear a distinct click.
-
Refill coolant. Pour OEM Land Rover coolant (not generic antifreeze) into the expansion tank until the minimum mark is reached. Start the engine briefly and top up as needed.
-
Bleed air pockets. On some models, you may need to open the cooling system bleed valve (small screw on the heater line) while refilling to release trapped air.
-
Reconnect the battery. Restore power and allow the engine management system to relearn sensor values (takes approximately 10 seconds after startup).
-
Test drive. Observe the temperature gauge for 10 minutes of mixed driving. It should stabilise at the mid-point and not fluctuate.
⚠️ Important: Do not open the cooling system while the engine is hot or running under pressure. Coolant can reach 120°C and cause severe burns. Always work on a cold engine and allow the system to depressurise. If you encounter any resistance or coolant leaks during installation, stop work and contact our support team at +44 203 943 9919.
OEM Part Numbers
This housing replaces: LR062498 · LR107288 · LR117568 · LR095895 · LR069809
Verify your part number before ordering. Check the original housing or your service records for exact fitment confirmation.
Ready to Restore Engine Stability?
Temperature gauge fluctuations and coolant weeping are early warnings that your thermostat housing is wearing out. This OEM-specification replacement stops the problem in its tracks and restores the precision cooling your Range Rover or Discovery demands.
Shop Cooling Parts
Use code 22GET20 for 20% off any two items.
⭐ 4.9/5 stars · 12,300+ reviews
🚚 Worldwide shipping via DHL, FedEx, UPS
💚 30-day money-back guarantee
📞 UK support: +44 203 943 9919
Disclaimer: Victorious Automotive is not affiliated with, endorsed by, or an official distributor of Land Rover, Range Rover, Jaguar Land Rover, or any OEM manufacturer. All product names, logos, and vehicle designations are registered trademarks of their respective owners. This product is an aftermarket part designed for compatibility with the listed vehicles and is sold as-is. Installation should be performed by a qualified technician. Victorious Automotive assumes no liability for improper installation, damage, or engine malfunction resulting from misuse. Always consult your vehicle's owner manual and seek professional guidance if uncertain.
